Post Buy Requirement
AC
Sharjha, United Arab Emirates
Add Review

Our Products

  1. Light Fitting 3 Products available
  2. Cables And Wire Accessories 3 Products available
  3. Clamps 4 Products available
  4. Cabinets & Enclosures 3 Products available
  5. Bushings 3 Products available
  6. Others 78 Products available

Other Products / Services

Explosion-proof Caution Spotlight Fittings


  • Explosion protection to
    -CENELEC
    -IEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Zone 21 and Zone 22
    Class 1, Zone 1 and Zone 2
    Class 1, Division 1, Groups A, B, C, D

  • Ultra-bright LED lamp, low power consumption and long service life.

  • Lamp colour: red, blue, yellow, green.

  • Enclosure in copper-free aluminium, powder coated surface, yellow (RAL1021).

View Complete Details

Proof Fluorescent Lamp


  • Explosion protection to
    -CENELEC
    -lEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Zone 21 and Zone 22
    Class I, Zone 1 and Zone 2
    Class I, Division 2, Groups A, B, C, D

  • Polycarbonate diffuser, high transmittance, resistance to heavy impact.

  • Main enclosure is extruding formed of copper-free aluminium, anodic-oxidation treatment for surface. Both ends of enclosures are die-casting formed of copper-free aluminium, powder coated surface.

  • Built-in electronic ballast, power factor 0.95.

  • Special-made mounting bracket, the illumination angle can be adjusted on request.

  • Emergency function is available on request.

  • End of lamp life (EOL) rectification effect protection

View Complete Details

Incandescent Hand Lamps


  • Explosion protection to
    -CENELEC
    -IEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Class I, Zone 1 and Zone 2
    Class l, Division 2, Groups A, B, C, D

  • Incandescent lamp: Max. 60W

  • Cable supplied on request

  • Handle in plastic, with control push button

  • Powder coated wire guard, white

  • Toughened glass cover resistant to temperature changes

  • Movable transformer available on request

View Complete Details

FLAMEPROOF ENERGY-SAVING LIGHTING


  • Explosion protection to
    -CENELEC
    -IEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Zone 21 and Zone 22
    Class I, Zone 1 and Zone 2
    Class I, Division 1, Groups A, B, C, D

  • Two enclosure types separately for 42W and 68W compact energy-saving lamps, with good performance including rapid starting, ash free, high lighting efficiency, long service life and energy saving, etc.

  • The luminous intensity of a 42W compact energy-saving lamp equals an 80W mercury lamp; the luminous intensity of a 68W compact energy-saving lamp equals an 125W mercury lamp.

  • Powder coated wire guard; white.

  • Toughened glass cover resistant to temperature changes,

View Complete Details

Led Street Lamps


  • Explosion protection to
    -CENELEC
    -IEC
    -NEC

  • Can be used in
    Zone 2
    Zone 21 and Zone 22
    Class I, Zone 2
    Class I, Division 2, Groups A, B, C, D

  • Five enclosure types: 60, 90, 120, 150, 180

  • Applicable lamp and power (max.180W)
    LED: 60W, 90W, 120W, 150W, 180W

  • Enclosure: Extrusion formed with good cooling performance.

  • Unique design without an external power supply; power accessories and lamp are integrated.

View Complete Details

LED TANK INSPECTION VESSEL LIGHT FITTINGS

LED Tank Inspection Vessel Light Fittings

  • Explosion protection to
    -CENELEC
    -IEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Zone 21 and Zone 22

  • Applicable lamp and power:
    LED lamps, energy-saving and long service life, 9W

  • Enclosure in copper-free aluminium, powder coated surface, yellow (RAL1021)

View Complete Details

Portable Searchlight



Portable Searchlight

  • Explosion protection to
    -CENELEC
    -IEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Zone 21 and Zone 22
    Class I, Zone 1 and Zone 2
    Class I, Division 1, Groups A, B, C, D

  • Safe and reliable: the product has reliable explosion-proof performance, can safely and reliably work in various hazardous areas. The battery is equipped with a PTC thermistor and temperature fuse; double-protected circuit, safety performance enhanced.

  • Efficient and energy-saving: equipped with a memory-free battery with long service life and low auto-discharge rate, it is economical and environmental friendly. Has an efficient solid state LED lamp, low energy consumption and long service life.

  • Waterproof and damage-proof: the enclosure is made of an imported alloy with high strength and excellent strong impact resistant performance. The unique sealing type has very good water-proof performance

  • Anti-strong interference: The scientific module driving circuit has strong anti-shock and anti-electromagnetic interference characteristics

  • Heat resistant: LED radiator and battery are effectively isolated which improves the stability of the light

  • Intelligent control: pulse dimming technology, strong light and working light modes can be changed at random. Has a battery detection indicator which can detect the working condition of the battery at any time. The intelligent charger is provided with a protection circuit

  • Portable and flexible: small volume, light weight. Handling possibilities such as hand held and on shoulder satisfy different working requirements.




View Complete Details

STRONG WORKING LIGHTS



Strong Working Lights

  • Explosion protection to
    -CENELEC
    -IEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Class I, Zone 1 and Zone 2
    Class I, Division 2, Groups A, B, C, D

  • Safe and reliable: the product has good explosion-proof performance and can safely and reliably work in various hazardous areas.

  • Efficient and energy-saving: special gas discharging lamp; high luminous efficiency, luminous flux is 5 times of that of a halogen lamp with the same power, illumination is 3 times that of a 100W halogen bulb, service life is 5-10 times of that of a normal halogen lamp, and for the same brightness the power consumption is 15% of that of a normal halogen lamp, good anti-shock effect, small heating value, safer and more reliable.

  • Waterproof and damage-proof: the light is totally sealed and can work normally in wet environments, a special alloy enclosure ensures the light can resist strong shock and impact

  • Economic and environmental friendly: the memory-free battery can be charged and laid aside for a year, the reserve of electricity is not less than 80% full after two years, it is not less than 50% low-voltage discharging protection circuit is set; reliably protects the battery and prolongs the service life

  • Convenient and durable: a unique lamp cap, the lighting angle can be adjusted at random and there are wheels at the bottom to easily to move the lamp

  • Other: normally a oodlight is provided; however a spotlight is available on request




View Complete Details

Air Rod Bases & Saddles

Air Rod Bases & Saddles

The role of an air termination system is to capture the lightning discharge current and dissipate it harmlessly to earth via the down conductor and earth termination system. Therefore it is important to use a correctly designed air termination system.


IEC/BS EN 62305-3 advocates the following, in any combination, for the design of the air termination:



  • Air rods (or finials) whether they are free standing masts or linked with conductors to form a mesh on the roof

  • Catenary (or suspended) conductors, whether they are supported by free standing masts or linked with conductors to form a mesh on the roof

  • Meshed conductor network that may lie in direct contact with the roof or be suspended above it (in the event that it is of paramount importance that the roof is not exposed to a direct lightning discharge) The standard makes it quite clear that all types of air termination systems that are used shall meet the positioning requirements laid down in the body of the standard. It highlights that the air termination components should be installed on corners, exposed points and edges of the structure.


The three basic methods recommended for determining the position of the air termination systems are:



  • The rolling sphere method

  • The protective angle method

  • The mesh method


View Complete Details

Air Rod Brackets

Air Rod Brackets

The role of an air termination system is to capture the lightning discharge current and dissipate it harmlessly to earth via the down conductor and earth termination system. Therefore it is important to use a correctly designed air termination system.


IEC/BS EN 62305-3 advocates the following, in any combination, for the design of the air termination:



  • Air rods (or finials) whether they are free standing masts or linked with conductors to form a mesh on the roof

  • Catenary (or suspended) conductors, whether they are supported by free standing masts or linked with conductors to form a mesh on the roof

  • Meshed conductor network that may lie in direct contact with the roof or be suspended above it (in the event that it is of paramount importance that the roof is not exposed to a direct lightning discharge) The standard makes it quite clear that all types of air termination systems that are used shall meet the positioning requirements laid down in the body of the standard. It highlights that the air termination components should be installed on corners, exposed points and edges of the structure.


The three basic methods recommended for determining the position of the air termination systems are:



  • The rolling sphere method

  • The protective angle method

  • The mesh method


View Complete Details

AIR RODS

The role of an air termination system is to capture the lightning discharge current and dissipate it harmlessly to earth via the down conductor and earth termination system. Therefore it is important to use a correctly designed air termination system.


IEC/BS EN 62305-3 advocates the following, in any combination, for the design of the air termination:



  • Air rods (or finials) whether they are free standing masts or linked with conductors to form a mesh on the roof

  • Catenary (or suspended) conductors, whether they are supported by free standing masts or linked with conductors to form a mesh on the roof

  • Meshed conductor network that may lie in direct contact with the roof or be suspended above it (in the event that it is of paramount importance that the roof is not exposed to a direct lightning discharge) The standard makes it quite clear that all types of air termination systems that are used shall meet the positioning requirements laid down in the body of the standard. It highlights that the air termination components should be installed on corners, exposed points and edges of the structure.


The three basic methods recommended for determining the position of the air termination systems are:



  • The rolling sphere method

  • The protective angle method

  • The mesh method

View Complete Details

Air Termination System

The role of an air termination system is to capture the lightning discharge current and dissipate it harmlessly to earth via the down conductor and earth termination system. Therefore it is important to use a correctly designed air termination system.


IEC/BS EN 62305-3 advocates the following, in any combination, for the design of the air termination:



  • Air rods (or finials) whether they are free standing masts or linked with conductors to form a mesh on the roof

  • Catenary (or suspended) conductors, whether they are supported by free standing masts or linked with conductors to form a mesh on the roof

  • Meshed conductor network that may lie in direct contact with the roof or be suspended above it (in the event that it is of paramount importance that the roof is not exposed to a direct lightning discharge) The standard makes it quite clear that all types of air termination systems that are used shall meet the positioning requirements laid down in the body of the standard. It highlights that the air termination components should be installed on corners, exposed points and edges of the structure.


The three basic methods recommended for determining the position of the air termination systems are:



  • The rolling sphere method

  • The protective angle method

  • The mesh method

View Complete Details

ANTI-VANDAL CONDUCTOR GUARD

By far the largest and most important component of any structural lightningprotection or earthing system is the actual conductor.


Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer.


A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements.


Specification will depend on whether the application is for anabove ground structural lightning protection system, ora below ground earthing installation.Conductors for structural lightning protection systems


Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties.


The following sizes are suitable for the majority of above ground lightning protection systems:



  • Flat tape conductor
    25 x 3 mm bare tape, or 25 x 3mm PVC covered tape

  • Solid circular conductor
    8 mm diameter bare or PVC covered solid
    circular conductor

  • Stranded conductor
    70 mm bare or PVC covered stranded conductor

View Complete Details

Bare Conductor

By far the largest and most important component of any structural lightningprotection or earthing system is the actual conductor.


Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer.


A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements.


Specification will depend on whether the application is for anabove ground structural lightning protection system, ora below ground earthing installation.Conductors for structural lightning protection systems


Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties.


The following sizes are suitable for the majority of above ground lightning protection systems:



  • Flat tape conductor
    25 x 3 mm bare tape, or 25 x 3mm PVC covered tape

  • Solid circular conductor
    8 mm diameter bare or PVC covered solid
    circular conductor

  • Stranded conductor
    70 mm bare or PVC covered stranded conductor

View Complete Details

BIMETALLIC CABLE CONDUCTOR

Bimetallic CableConductor

By far the largest and most important component of any structural lightningprotection or earthing system is the actual conductor.


Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer.


A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements.


Specification will depend on whether the application is for anabove ground structural lightning protection system, ora below ground earthing installation.Conductors for structural lightning protection systems


Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties.


The following sizes are suitable for the majority of above ground lightning protection systems:



  • Flat tape conductor
    25 x 3 mm bare tape, or 25 x 3mm PVC covered tape

  • Solid circular conductor
    8 mm diameter bare or PVC covered solid
    circular conductor

  • Stranded conductor
    70 mm bare or PVC covered stranded conductor


View Complete Details

Flexible Braid

By far the largest and most important component of any structural lightningprotection or earthing system is the actual conductor.


Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer.


A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements.


Specification will depend on whether the application is for anabove ground structural lightning protection system, ora below ground earthing installation.Conductors for structural lightning protection systems


Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties.


The following sizes are suitable for the majority of above ground lightning protection systems:



  • Flat tape conductor
    25 x 3 mm bare tape, or 25 x 3mm PVC covered tape

  • Solid circular conductor
    8 mm diameter bare or PVC covered solid
    circular conductor

  • Stranded conductor
    70 mm bare or PVC covered stranded conductor

View Complete Details

HARD DRAWN BAR

Hard Drawn Bar

By far the largest and most important component of any structural lightningprotection or earthing system is the actual conductor.


Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer.


A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements.


Specification will depend on whether the application is for anabove ground structural lightning protection system, ora below ground earthing installation.Conductors for structural lightning protection systems


Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties.


The following sizes are suitable for the majority of above ground lightning protection systems:



  • Flat tape conductor
    25 x 3 mm bare tape, or 25 x 3mm PVC covered tape

  • Solid circular conductor
    8 mm diameter bare or PVC covered solid
    circular conductor

  • Stranded conductor
    70 mm bare or PVC covered stranded conductor


View Complete Details

LEAD COVERED CONDUCTOR

Lead Covered Conductor

By far the largest and most important component of any structural lightningprotection or earthing system is the actual conductor.


Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer.


A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements.


Specification will depend on whether the application is for anabove ground structural lightning protection system, ora below ground earthing installation.Conductors for structural lightning protection systems


Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties.


The following sizes are suitable for the majority of above ground lightning protection systems:



  • Flat tape conductor
    25 x 3 mm bare tape, or 25 x 3mm PVC covered tape

  • Solid circular conductor
    8 mm diameter bare or PVC covered solid
    circular conductor

  • Stranded conductor
    70 mm bare or PVC covered stranded conductor

View Complete Details

PVC COVERED CONDUCTOR

PVC Covered Conductor

By far the largest and most important component of any structural lightningprotection or earthing system is the actual conductor.


Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer.


A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements.


Specification will depend on whether the application is for anabove ground structural lightning protection system, ora below ground earthing installation.Conductors for structural lightning protection systems


Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties.


The following sizes are suitable for the majority of above ground lightning protection systems:



  • Flat tape conductor
    25 x 3 mm bare tape, or 25 x 3mm PVC covered tape

  • Solid circular conductor
    8 mm diameter bare or PVC covered solid
    circular conductor

  • Stranded conductor
    70 mm bare or PVC covered stranded conductor


View Complete Details

ROD TO CONDUCTOR COUPLING

The role of an air termination system is to capture the lightning discharge current and dissipate it harmlessly to earth via the down conductor and earth termination system. Therefore it is important to use a correctly designed air termination system.


IEC/BS EN 62305-3 advocates the following, in any combination, for the design of the air termination:



  • Air rods (or finials) whether they are free standing masts or linked with conductors to form a mesh on the roof

  • Catenary (or suspended) conductors, whether they are supported by free standing masts or linked with conductors to form a mesh on the roof

  • Meshed conductor network that may lie in direct contact with the roof or be suspended above it (in the event that it is of paramount importance that the roof is not exposed to a direct lightning discharge) The standard makes it quite clear that all types of air termination systems that are used shall meet the positioning requirements laid down in the body of the standard. It highlights that the air termination components should be installed on corners, exposed points and edges of the structure.


The three basic methods recommended for determining the position of the air termination systems are:



  • The rolling sphere method

  • The protective angle method

  • The mesh method

View Complete Details

Strike Pad

The role of an air termination system is to capture the lightning discharge current and dissipate it harmlessly to earth via the down conductor and earth termination system. Therefore it is important to use a correctly designed air termination system.


IEC/BS EN 62305-3 advocates the following, in any combination, for the design of the air termination:



  • Air rods (or finials) whether they are free standing masts or linked with conductors to form a mesh on the roof

  • Catenary (or suspended) conductors, whether they are supported by free standing masts or linked with conductors to form a mesh on the roof

  • Meshed conductor network that may lie in direct contact with the roof or be suspended above it (in the event that it is of paramount importance that the roof is not exposed to a direct lightning discharge) The standard makes it quite clear that all types of air termination systems that are used shall meet the positioning requirements laid down in the body of the standard. It highlights that the air termination components should be installed on corners, exposed points and edges of the structure.


The three basic methods recommended for determining the position of the air termination systems are:



  • The rolling sphere method

  • The protective angle method

  • The mesh method

View Complete Details

TINNED CONDUCTOR

Tinned Conductor

By far the largest and most important component of any structural lightningprotection or earthing system is the actual conductor.


Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer.


A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements.


Specification will depend on whether the application is for anabove ground structural lightning protection system, ora below ground earthing installation.Conductors for structural lightning protection systems


Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties.


The following sizes are suitable for the majority of above ground lightning protection systems:



  • Flat tape conductor
    25 x 3 mm bare tape, or 25 x 3mm PVC covered tape

  • Solid circular conductor
    8 mm diameter bare or PVC covered solid
    circular conductor

  • Stranded conductor
    70 mm bare or PVC covered stranded conductor


View Complete Details

Access Fittings

The National Electrical Code defines a conduit body as A separate portion of a conduit or tubing system that provides access through a removable cover(s) to the interior of the system at a junction of two or more sections of the system or at a terminal point of the system.


Available with Self Tapping Screws / Brass Screws & Inserts



  • Type C

  • Type LB

  • Type LL

  • Type LR

  • Type E

  • Type T

  • Type TB

View Complete Details

Terminal Adapters

Adapters


Reduce conduit hubs to a smaller size or to connect two different sizes of conduit together



  • Terminal Adapters

  • Female Adapters (NPT Tapered Thread)

View Complete Details

PVC LSF Building Wires And Cables

PVC LSF Building Wires and Cables

Aswathy can provide the full range of house wiring cables from 1.5 mm to 1000 mm with wide range of core colours. The conductor is plain annealed solid or stranded Copper conductors insulated withPVC or Heat Resistant PVC as per BS EN 50535-3-41. Oman Cablesalso manufactures twin flat wires up to 6mm with or without Earth continuity conductor.


The complete range of Wiring cables can be manufactured using Low Smoke Zero Halogen thermosetting insulation compounds conforming to BS EN 50535-2-31 or with compounds to suit customers specific requirements.

View Complete Details

Cable Ladder System

Cable Ladder System is designed to offer high loading capacities together with significant weight reductions. Cable Ladders are designed to be safe, and give distinct benefits.



  • For light loads such as instrumentation, data & telecom cables

  • Corrosion resistant fibre reinforced plastic ladders

  • Smart Cable Ladders for Ships

  • Cable ladder for infrastructure Projects



Features:

  • Solid side rail protection and system strength with smooth radius fittings.

  • Maximum strength for long span applications

  • Standard widths of 6, 12, 18, 24, 30 & 36 inches

  • Standard depths of 3, 4, 5 & 6 inches

  • Standard lengths of 10, 12, 20 & 24 feet

  • Rung spacing of 6, 9, 12 & 18 inches

View Complete Details

Cable Tray

Cable Trays are made of either Steel, Aluminum, Fiber Reinforced Plastic (FRP) and we provide the following six different types and are available in Standard Width, Depth and Length



  • Ladder Type Cable Tray

  • Solid Bottom Cable Tray

  • Trough Cable Tray

  • Channel Cable Tray

  • Wire Mesh Cable Tray

  • Single Rail Cable Tray

View Complete Details

Cantilever Arm

Cantilever Arm
We supply a range of simple to install cantilever support arms which can be used for supporting Cable Ladders and Cable Trays. They can also be fixed directly to wall.







  • Offshore Cantilever Arm

  • Onshore Cantilever Arm

  • Channel Bracket Cantilever Arm for Channel support

  • Single Cantilever

  • Double Cantilever





View Complete Details

Fire Resistant Cables



Fire Resistant Cables

600/1000V grade , plan annealed copper conductor, glass mica tapped, XLPE insulated, multi-core cables laid up and inner sheathed with LSF (or LSOH/LSZH), round galvanized steel wire armoured and outer jacket with LSF (or LSOH/LSZH). Specifications: BS7846 (Category F2) and BS 6387 (Category, C, W & Z). These Cables are meant for maintaining circuit integrity under fire condition for 3 hours (tested for 3 hours at 950o C temperature).


Range:From 2C x 1.5mm to 4C x 400mm From 5C x 1.5mm to 5C x 70 mm




View Complete Details

Lighting Poles

Available in Steel, Aluminum, Fiberglass, RCC



  • Anchor / Burial / Hinged Base

  • Round / Square / Straight / Tapered Shaft

  • Octagonal, Stepped or Round type

  • Street / Flood Straight and Hinged

  • Towers, Compound, High Masts, Street, Stadium, Plant and Special Design

  • Special Design Poles.

  • Flag Posts

  • Flood Light Towers

View Complete Details

Low Voltage Cables

XLPE Insulated Power Cables

600/1000 V grade, plain annealed Copper conductor. XLPE insulated, multi-core cables laid up andinner sheathed with PVC, round galvanized steel wire armored for multi cores and aluminium wirearmored for single cores and outer jacket with PVC.


Range:



  • From 1C x 10 mmto 1C x 1000 mm

  • From 2C x 1.5 mm to 4C x 400 mm


Specification:BS-5467, IEC 60502, part-1;S-6724 as per Iraq specs or any other international standards, as well as customer specification. We also manufacture the cables for special applications which requireenhanced fire performances as per IEC-60332-3, Low Smoke Zero Halogen characteristics as perBS6724, lead sheathed cables, anti-termite treatment, UV resistant & Water blocking feature, tinnedcopper wires in the armor for higher armor conductivity etc.


PVC Insulated Power Cables

600/1000V Grade Plain annealed Copper conductor, PVC insulated, multi-core cables laid up and inner-sheathed with PVC, round galvanized steel wirearmored for multi-cores and aluminium wire armored for single core and outer jacket with PVC.


Range:



  • From 1C x 10 mm to 1C x 1000 mm

  • From 2C x 1.5 mm to 4C x 400 mm


Specifications:IEC-60502 Part-1, as per Iraq specs or any other international standards as well as customer specifications. We also manufacture the cables
for special applications which require enhance fire performance as per IEC-60332-1 & IEC-60332-3, lead sheathed cables, anti-termite treatment, UV
resistant, water blocking feature, tinned copper wires in the armor for higher armor conductivity etc.

View Complete Details

Tubing Clamps

Tubing Clamps


Tubing clamps are quick and easy to install and can be stacked and staggered to maximize the fitting space available. The protected clamps are independently vibration tested and approved.
View Complete Details

Weatherproof Flexible Cable Conduits

Weatherproof Flexible Cable Conduits

  • Corrosion-proof, water-proof, anti-aging, good flexibility, rm structure, reliable performance, etc

  • The thread can be specially made upon request (NPT, metric thread etc)

  • The connector is made of high quality carbon steel. If requested, the whole conduit can be made of stainless steel.

  • The length of exible conduit can be specially made upon request.

View Complete Details

Overhead Line Conductors

Overhead Line Conductors

Aswathy has capability to provide completerange of overhead line conductors inAluminium, Aluminium Alloy and Copper.The standard range includes sizes up to1000mm as per BS, IEC, DIN, ASTM, or any other international standard andcustomers specifications for all voltageapplications. We can also provide conductorswith XLPE or PVC covering.The standard types of conductors in ourpresent manufacturing range are as follows:



  • AAC All Aluminium Conductors

  • AAAC All Aluminium Alloy Conductor

  • ACSR Aluminium Conductor Steel Reinforced

  • HDBC Hard Drawn Bare Copper conductor

  • SDBC Soft Drawn Bare copper Conductor

  • AAC + XLPE All Aluminium Conductor with XLPE insulation

  • AAC + PVC All Aluminium conductors with PVE insulation


View Complete Details

Perforated Profiles

Perforated Profiles
We offer a range of standard perforated profiles suitable for welding during construction. These can then be treated and coated together with the main structure.
View Complete Details

RACKS, INSTRUMENT STANDS AND EQUIPMENT PLATES

Racks, Instrument Stands and Equipment Plates
Aswathysrange of equipment rack designs provide optimal area utilization and are easy and quick to install. We also has a range of different solutions for instrument stands and our versatile equipment plates are designed to fit a range of different equipment from multiple suppliers. Custom made versions are also available.
View Complete Details

Light Weight And Cost Saving Support System

Support System
Flexible, light weight and cost saving support system for all main disciplines including electrical, instrumentation, telecom, HVAC and piping. sections are available in a range of profiles, grades and materials to suit any application, however all share the same high quality engineering solutions. When compared to traditional welded supports, oursystems are significantly lighter, quicker to install, safer in construction and more cost effective. Systems offer full flexibility in design and installation both in initial construction and in all subsequent adaptation or upgrade works.
View Complete Details

Ac Contactors



AC Contactors

  • Explosion protection to
    -CENELEC
    -IEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Class I, Zone 1 and Zane 2
    Class I, Division 2, Groups A, B, C, D

  • Product of flame-proof structure; the cavity is of engineering plastic embedded with high strength metal frame structure; with strong corrosion-proof capacity and reliable performance;

  • Built-in Schneider AC contactor with 3 pairs of main contacts and as many as 4 pairs of auxiliary contacts for easy for wiring.




View Complete Details

Ammeters / Voltmeters


  • Explosion protection to
    -CENELEC
    -IEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Zone 21 and Zone 22
    Class I, Zone 1 and Zone 2
    Class I, Division 2, Groups A, B, C, D

  • Fast comparison of measured and set values

  • Versions available
    -Ammeter (type 72)
    -Voltmeter (type 72)

View Complete Details

Circuit Breaker Modules



Circuit Breaker Modules

  • Explosion protection to
    -CENELEC
    -IEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Class I, Zone 1 and Zone 2
    Class I, Division 2, Groups A, B, C, D

  • Product of ame-proof structure; the cavity is of engineering plastic embedded with high strength metal frame structure; with strong corrosion-proof capacity and reliable performance.

  • Built-in Schneider iC65 series MCB, special operation mechanism internally designed, reliable overall operation.




View Complete Details

Connectors





  • Explosion protection to
    -CENELEC
    -IEC

  • Can be used in
    Zone 1 and Zone 2
    Zone 21 and Zone 22

  • Available in nickel plated brass, stainless steel or galvanized carbon steel.

  • High quality carbon steel. Stainless steel or other material is available on request

  • Weather proof flexible connector, thethread can be specially made upon request, such as NPT thread, metric thread etc



View Complete Details

Control Buttons


  • Explosion protection to
    -CENELEC
    -IEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Zone 21 and Zone 22
    Class I, Zone 1 and Zone 2
    Class I, Division 2, Groups A, B, C, D

  • 2 versions of component
    -1 NO
    -1 NC

  • Six different ways of operation
    -Spring-return control button
    -Mushroom stay-put emergency control button
    -Key-operated control button
    -Rotary control button
    -Double control button
    -Mushroom turn-to-release emergency control button

  • Mushroom stay-put emergency push button/mushroom turn-to-release emergency push button can be equipped with protection cover, please specify when ordering. Material of protection cover: stainless steel and PC, please specify when ordering

View Complete Details

Control Switches

Control Switches

  • Explosion protection to
    -CENELEC
    -lEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Zone 21 and Zone 22
    Class l, Zone 1 and Zone 2
    Class I, Division 2, Groups A, B, C, D

  • Number of pole: 2P, 3P, 4P, 6P.

  • Available in latching and spring-return forms

View Complete Details

Weatherproof Control Unit Systems

Control Unit Systems

  • Explosion protection to
    -CENELEC
    -IEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Zone 21 and Zone 22
    Class I, Zone 1 and Zone 2
    Class l, Division 1, Groups A, B, C, D

  • Copper-free aluminium, powder coated surface, GRP Enclosures

  • Individual unit can be combined into larger units.



WeatherproofControl Unit Systems

  • Enclosure is made of pressed engineering plastics with an attractive appearance

  • Anti-aging, deformation-free, impact resistant and corrosion resistant etc.

  • The product has strong acid and strong alkali resistance, anti-salt, anti-seawater and chloride corrosion resistance.

  • Built-in components: button, indicator, etc. The brand of inner components shall be recommended by Manufacturer.

  • Note: no more than 3 units can be installed, such as, one button, two buttons, three buttons, one button and one light, one button and one switch, two buttons and one light, etc. If more than 3 units are required a control station should be used.

View Complete Details

Distribution Boxes

Distribution Boxes

  • Explosion protection to
    -CENELEC
    -IEC
    -NEC

  • Can be used in
    Zone 1 and Zone 2
    Zone 21 and Zone 22
    Class I, Zone 1 and Zone 2
    Class I, Division 2, Groups A, B, C, D

  • Enclosure for modular combination (Ex d & Ex e).

  • Main switch and branch switch are operated with external rotary actuator.

  • Internal wiring to the terminal is complete.

  • International brand of explosion-proof terminal used.

  • Copper-free aluminium, powder coated surface.

  • Entries plugged. Cable glands on request (seehere).

  • Special requirements on request.


  • WeatherproofDistribution Boxes

    • Attractive appearance, safe and reliable

    • Widely used in factories, hotels, shopping malls, residences etc.

    • Metal panels (cold rolled steel plate) and stainless steel panels are available

    • Easy installation, disassembly and maintenance

    • MCB (miniature circuit breaker) can be supplied upon request

    • The enclosure can be made of engineering plastic if required,



View Complete Details

Pressurized Distribution Cabinets

PressurizedDistribution Cabinets

  • Explosion protection to
    -CENELEC
    -IEC

  • Can be used in
    Zone 1 and Zone 2
    Zone 21 and Zone 22

  • Explosion-proof types llB, IIC.

  • Available in types G, X, Q, T, K.

  • The product consists of a main cavity and an auxiliary cavity. The main cavity is pressurized and equipped with electrical components to user requirements and a pressure check sensor system, ventilation air distribution system, and air conditioning system, etc.; the auxiliary cavity is installed with explosion-proof ventilation auto-control system, explosion-proof power auto-off system, explosion-proof alarm system, explosion-proof pressure display system, and air in/out connector; the auxiliary cavity with auto-air supply
    is equipped with an explosion-proof air supply device.

  • The cabinet is manufactured from high quality welded steel plate with front operation and rear maintenance access.

  • The back doors of the cabinet type and piano type cabinets can be quickly opened and are convenient for installation and maintenance


  • WeatherproofDistribution Cabinets

    • The cabinet is made of high-quality carbon steel bent and welded plate with a powder coated surface finish.

    • Built-in various low-voltage electrical apparatus

    • Cabinet dimensions can be made according to the electrical schematics and main technical parameters provided by the user;

    • Appropriate low-voltage electrical apparatus shall be used.

    • Front door or back door as well as double-door can be made to users requirements.

    • Applicable operation modes: direct operation on the panel, or open the door to operate.

    • Degree of protection up to IP65; can be used outdoors.

    • Stainless steel enclosure can be made on request



View Complete Details

Dry Type Transformer


  • Can be used in

    • Zone 1 and Zone 2

    • Zone 21 and Zone 22

    • Class I, Zone 1 and Zone 2

    • Class I, Zone 1, Group B, C, D



  • Flameproof enclosure (Ex d llB+H2)

  • Enclosure: carbon steel, stainless steel

  • Built-in dry-type transformer can be used for step-up and step-down in distribution system

  • Six type of rated capacity: 5kVA, 15kVA, 3OkVA, 45kVA, 60kVA, 75kVA.

  • Equipped with a specialized hinge structure which can prevent damage to the ameproof joints when opening and closing the box, ; greatly prolongs the service life of the box.

  • Special user requirements incorporated on request.

View Complete Details

Window Air Conditioner


  • Explosion protection to

    • IECEx

    • CENELEC



  • Can be used in:

    • Zone 2



  • For explosion-proof window air conditioners, the corresponding product is a cooling-only air conditioner in T1 and T3 group.

  • Perfect for use in high temperature areas such as the Middle East, Middle Africa, Southeast Asia and tropical zones near the equator (Cooling only)

  • The explosion proof window air conditioner is based on a renown brand air-conditioner, with explosion proof modifications made to the internal control units, compressor, indoor and outdoor fan motors, temperature sensor system, protective system, heat-removal system, cooling system, etc. The original outline dimensions and installation are maintained as per the original.

  • ions and installation are the same as the original after explosion-proof treatment

View Complete Details

Weatherproof Light Switches

WeatherproofLight Switches

  • The product is made of a glass fiber reinforced unsaturated polyester resin compression molding, with an attractive appearance,

  • anti-aging, deformation-free, impact resistance and corrosion resistance etc.

  • All exposed fasteners are made of stainless steel. Sealing parts are made of silicone rubber, with anti-oil, anti-acid, anti-alkali, high temperature resistance and ageing resistance.

  • Labyrinth waterproof structure, good waterproof and dust-proof performance:

  • The product has strong acid and strong alkali resistance, anti-salt, anti-seawater and chloridion corrosion resistance.

View Complete Details

STAINLESS STEEL EXPLOSION-PROOF FLEXIBLE CONDUIT

Stainless Steel Explosion-proof Flexible Conduit

  • Explosion protection to

    • CENELEC

    • IEC

    • NEC



  • Can be used in

    • Zone 1 and Zone 2

    • Zone 21 and Zone 22

    • Class I, Zone 1 and Zone 2

    • Class I, Division 1, Groups A, B, C, D



  • Ex d structure; stainless steel body; connectors at both ends in stainless steel.

  • Application:

    • Widely used for flexible connection between explosion-proof boxes or explosion-proof light fittings and pipes

    • Protect cable from any damage

    • Highly corrosion-proof



View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • Mr. Aneeshkumar M. Pillai (Aswathy Corporation Fzc.)
  • Executive Suite Z 2 – 15, SAIF Zone, Post Box 121477 SHARJAH, UNITED ARAB EMIRATES, Sharjha, United Arab Emirates
  • Share us via