Post Buy Requirement
BS
Dubai, United Arab Emirates
Add Review

Other Products / Services

Master Plug Screws

Master Plug systems are designed to work with most seaming jobs and almost any material:




  • Fastens blind holes and closed-end holes




  • Cushions and seals similar and non-similar materials




  • Absorbs vibration and seals both sides




  • Tapered design enhances fastening installation




  • Ozone and ultra violet exposure light resistant




  • Removable and reinsertable




All Master Plug materials are effective against cracking, leaking and ozone.

View Complete Details

Sandwish Panel Anchor System

PHILIPP Sandwish Panel Anchor System has several advantages:



  • Reduction of mounting and planning effort

  • Minimal thermal bridge through the fastening system

  • Use of high quality stainless steel in anchor for lasting corrosion resistance

  • Uniform load transfer in thin-walled elements through load balancing between several support anchors

  • Simple system adjustment even for geometrically complicated elements

  • Insulating layer thickness up to 20cm possible

  • Connector pins can be used without further calculation under observation of the default boundary conditions

  • Structural standard accounts for wind load as well as stress from temperature changes and shrinkage

  • The inspected system does not restrict the progress of the construction work

  • Comprehensible and simple installation of anchors and pins

View Complete Details

Self Tapping Screws

Self Tapping Screws are sheet metal screws and require pre-drilling.
They are available in two types:

Type A:
Coarse thread / Sharp end point, recommended for use on steel purlins with thickness not exceeding 2.67mm

Type B:
Fine thread / Flat end point, recommended for use on steel purlins with thickness exceeding 2.67mm

They are available in Carbon Steel (Ruspert or Tufcote coating), Stainless Steel grade 304 & 316

View Complete Details

Self Drilling Screws

Self Drilling Screws are sheet metal screws and do not require pre-drilling. The screw will do the drilling & tapping.

Carbon Steel Self Drilling Screws come with different drilling capacity and are available with Ruspert or Tufcote coating

Stainless Steel Self Drilling Screws can be made from SS410 or will be Bi-Metal in either SS304 or SS316. They are called Bi-Metal because they are made of two different metals:


The head & threaded part is made of stainless steelThe drill bit is made of carbon steel and is welded thru a unique process to the threaded part

Bi-Metal Self Drilling Screws can be Tufcote or Ruspert coated or Zinc Plated to protect the carbon steel drill bit from fast corrosion.

View Complete Details

Color Screw Caps

Screw Color Caps are used to protect the screw from harsh environment and come in different colors to match the color of the sheet.

Color Caps are U.V. Stabilized.

View Complete Details

Swenn Saddle Washers

Saddle Washers offer stability to the screw fixing and minimize the leaking on the fixing point.

Saddle Washers are used in ridge fixings of profiled, trapezoidal and corrugated sheets.

They are made of Aluminium sheets vulcanized to EPDM seal and can be produced to fit on any profile.

View Complete Details

Butyl Strip Sealant

Butyl Strip Sealant (Ropeseal) for metallic roofing and double glazing.

Ropeseal is a high performance butyl tape suitable for use in steel and aluminium roofing systems. It has been carefully formulated to provide a long life, airtight & watertight seal to help buildings comply with buildings regulations.

Good Adhesion to metal roofing panels, strong, flexible, and designed specifically to accommodate movement, excellent UV resistance.

Ropeseal can be used on external metal sheeting (end & side laps), rooflights, ridge & caves sealing in combination with foam fillers
Ropeseal is covered by the manufacturers guarantee for 20 years

View Complete Details

Sheeting Repair Butyl Tape

Foilband 0315 is a butyl tape laminated with a fixed foil backing. It has been carefully formulated to provide a long life, airtight and watertight seal, and to be used on various applications: Gutters, drain pipes, steel sheeting, sectional building, air conditioning & ventilation ducts.

Foilband has: Good adhesion to a wide range of substrates, excellent tear & puncture resistance, good UV resistance.

Foilband remains flexible throughout its service life.
Foilband is covered by the manufacturers guarantee for 15 years

View Complete Details

Purlin Tape

Purlin Tapes, also called Barrier Tapes are used on the purlin to avoid contact between the steel purlin & the aluminium sheet.


It is waterproof and made of polyethylene film with a polyester / cotton blend cloth carrier.


It comes in Silver color.


Two types are available:


PC590


PC600

Physical Properties

PC 590

PC 600

Tensile Strength

35.0 N / 10 mm

38.5 N / 10 mm

Adhesion to Stainless Steel

4.93 N / 10 mm

5.47 N / 10 mm

Thickness

0.18 mm

0.23 mm

Elongation

15%

10%

Service Temperature Range

10°C to 93°C

10°C to 93°C

Dielectric Strength

7.0 KV

6.0 KV

View Complete Details

Silicone Sealant

1200GC is a fast curing one part silicone sealant, which cures with atmospheric moisture to form a high strength rubber seal with excellent adhesion to glass, glazed surfaces, metals, most plastics and covered surfaces.


1200GC has excellent physical properties which are designed to give outstanding durability and performance.


Available in different colors.

View Complete Details

Spherical Head Lifting Clutch

PHILIPP Spherical Head Lifting Clutch is constructed in a way that an unintended coupling off (even without tension by a lifting device) is impossible. On lifting, attention must be paid that the lip shows into the direction of tension.

PHILIPP Spherical Head Lifting Clutch is suitable for all directions (axial, diagonal and lateral tension). Coupling on/off can be made easily with one hand.

This clutch may be used in combination with the original PHILIPP Spherical Head Transport Anchor

View Complete Details

Lifting Insert With Cross Hole

PHILIPP Lifting Insert is a lifting insert with cross hole with threads on both sides.

Once used, attention must be paid to the general instruction for installation and use.

PHILIPP Lifting Inserts are used for transport of precast concrete units.

The insert may only be used with PHILIPP devices.

View Complete Details

Fixing Socket

Fixing Sockets (also called Cast-In Sockets), have an internal thread and a cross hole on the flat-crimped end.



Fixing Sockets are used to transport precast concrete units+

View Complete Details

Lifting Loop

PHILIPP Lifting Loops are only permissible for axial tension and diagonal tension up to 45.Incorrect applications regarding the load direction lead to damage at rope or thread.

PHILIPP Lifting Loops consist of special steel wire rope in galvanized quality. The threaded part is made of bright precision steel.

PHILIPP Lifting Loops are used as lifting devices with PHILIPP threaded anchor systems and can be turned in or out of the threaded anchor like a standard screw. The PHILIPP Lifting Loop must be screwed in completely.

PHILIPP Lifting Loops are available with metric thread or with special RD-thread (with metric pitch)

View Complete Details

Swivel Lifting Device

PHILIPP Swivel Lifting Device consists of a forged ring bolt with a chain link and a bottom part made of special hardened steel. The inside construction consists of a bearing inlay.

The use of PHILIPP Swivel Lifting Device in a sunk position with nailing plates with too small diameters is inadmissible. Because of its ball-bearing, the hanger moves after achievement of the nominal load bearing itself into the right force direction without removing the bottom part of the Philipp Swivel Lifting Device.

View Complete Details

Connecting Loop

PHILIPP Connecting Loops are used for structural connections of precast units loaded by primarily static shear forces. The loops transfer shear forces where no approval is required.

PHILIPP Connecting Loops are very flexible and form a connection due to the overlapping of the loops. Therefore, it is possible to easily realize even complicated connections.

PHILIPP Connecting Loops can be used without additional proofs. The simple installation ensures practical application.

PHILIPP Connecting Loop is a connecting element for the form closed connection of precast units. The flexible loops have the advantage that no reverse bending is required and hence the installation of precast units between columns is realizable.

PHILIPP Connecting Loop consists of a plastic or galvanized steel recess former and is suitable for reinforced concrete and light weight concrete.

View Complete Details

Hole Anchor System

PHILIPP Hole Anchor System consists of a steel component insert into the concrete (the anchor) and a lifting component (the ring clutch). The precast unit is lifted and transported by means of a ring clutch, which is locked to the anchor cast into concrete. The design and shape of the ring clutch and anchor enable the lifting of the load in almost any load direction. The ring clutch can be unlocked either manually, direct at the clutch head, or by remote release

View Complete Details

DTI-Load Tension Indicators

Direct Tension Indicators (DTIs) are recognized by many engineers as the most reliable method for ensuring correct installation of high strength bolts according to that specification for both shear / bearing connections requiring fully pretensioned bolts.

DTIs are simple and extremely accurate devices for ensuring that bolts have been installed above the specified minimum tension value

View Complete Details

Expansion Bolts

Expansion Bolts, also called Wedge Anchors are used to anchor fixtures into concrete. They work by inserting them into a hole drilled into concrete. The Wedge Anchor is then expanded, wedging itself securely in the concrete.


They are available in Stainless Steel Grade 304, Stainless Steel Grade 316, Zinc Plated Carbon Steel.

View Complete Details

J Anchors

  • Country of Origin India
  • Type Castle Nut
  • Color Metallic
  • Diameter 40-50mm
  • Weight 0-20 Gm

We can supply a big variety on anchors:


J AnchorsL AnchorsU AnchorsStraight AnchorsMetal Cavity AnchorsAnd many others


For "J", "L", "U" anchors, send us your detailed enquiries with drawings and we'll send you our offer.

View Complete Details

Stud Welding Machine

Fully integrated stud welding systems having two digital controls for time and current. TRU-WELD stud welding machines were designed to meet the most challenging stud welding jobs including thru-deck applications.


A complete system includes:

*Power supply controller The machine
*TWE 17000 heavy duty stud gun
*50 ft (15 meters) of 4/0 weld and control cable
*25 ft (7.5 meters) of 4/0 ground cable with HD clamp
*Trolley


The latest introduced model SC 2402 can weld studs ranging from 1/4" to 1-1/4 and can weld thru G-90 deck

View Complete Details

Shear Studs And Ceramic Ferrules

TRU-WELD offer a wide range of shear studs covering the majority of studs requirements. Studs are available in several diameters and lengths. The length of the stud is reduced approximately 1/8 to inch during the welding operation, this change must be considered when selecting a stud to fit a particular application. TRU-WELD studs are manufactured from ASTM A-108 Grades 1010 thru 1020 steel, which conforms to the applicable A.W.S. and I.C.B.O. standards.


All TRU-WELD studs are supplied with ceramic ferrules designed for use with the particular fastener ordered. Ferrules are specially designed of ball clay and talc, an excellent material to withstand heat shock as well as reasonably high temperatures without melting or breaking. TRU-WELD ferrules complement the perfect position arc initiator and the uniform flux load to effect a top quality weld.


An important part of the stud is the FLUX. The FLUX load is designed to assure excellent weld quality

View Complete Details

Drawn Arc Stud Welding Machine

MULTI AS is a compact stud welding machine for drawn arc stud welding.

This handy, powerful stud welding machine can be used for universal application, it is compact, robust and ideal for field use.

Used for welding elements according to DIN 32500 and DIN 32501 and special metallic shaped parts of alloyed and unalloyed steel, the machine can be provided with an inert-gas control, so that ferrule is not necessary for welding.


Depending on the particular application, special damped or un-damped guns are available with suitable ferrule support, inert-gas support or support for short-cycle welding guns with or without automatic length compensation.

View Complete Details

Refractory Anchors, Threaded & Non-Threaded Studs, Insulation Pins

Threaded and non-threaded welding studs for drawn arc, capacitor discharge and short cycle.

Available in different types, materials (Steel grade 4.8, Stainless Steel) and sizes.


Insulation Pins for drawn arc welding.
Available in different materials (Steel grade 4.8, Stainless Steel) and sizes.


Heat-Resistant Fastening Systems Refractory Anchors
Available in different types (Round bar anchors, flat bar anchors, slotted studs, brick anchors ., sizes & materials (Steel grade 4.8, Stainless Steel)

View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • Bright Star Construction Materials LLC (Bright Star Construction Materials LLC)
  • P.O.Box 12862, Dubai, United Arab Emirates
  • Share us via