Post Buy Requirement
EE
Abu Dhabi, United Arab Emirates
Add Review

Our Products

Hydraulic Hoses

Hydraulic hose provides a basic means for transferring hydraulic fluid from one component to another in hydraulic system, and at the same time it provides an inherent versatility to hydraulic systems designers.


To consider hydraulic system hose is an important part of a hydraulic system is a huge understatement. The flexibility of hose enables hydraulic systems components to be positioned/located in the most efficient or convenient places, due to the fact that hydraulic hose has the ability to bend around corners, through tight spaces, or across long distances.



EmiratesGreen offer range of hoses for hydraulic systems applications/uses:

  1. Single wire Hydraulic Hose with type R1. Sizes from to 2 WP 225 to WP 40 Bar (Approx.)

  2. Double wire Hydraulic Hoses with type R2. Sizes from ID to 2 ID WP 400 Bar to 80 Bar.

  3. Hydraulic Hoses with 4 wire with WP to 280 Bar sizes as follows:

    • 4SH to 2 = 420 Bar to 280 Bar.

    • 4Sp 3/8 to = 450 Bar to 400 Bar.

    • Hydraulic Spiral Hoses with sizes 3/8 to 4SP type with flexible bending radius.

    • Hydraulic Spiral Hoses with Steel Hard wire with sizes to 2 WP 420 Bar to 280 Bar.

    • More than 400 Bar Hose for 1 inch size can be arrange against order R13/R15.



  4. Hydraulic Hoses with BOP Application.

    • Hydraulic Hose with WP Pressure 6000 PSI with factory assembled fittings with ABS/ Type Approval Certification for completely Assy.

    • Approx. Length 100 Feet with WPT (M) fitting in SS316 fitting at both ends.



  5. Hydraulic Hose for Jack Lifting Application.

    • Jack Hose 790 Bar with Carbon Steel & SS316 fittings at both ends.

    • If required QRC available separately provided for Assy



    Types of Hydraulic Hoses

    • Type R1 WP 225 to 40 Bar size to 2 *(ID)

    • Type R2 WP 400 Bar to 80 Bar size to 2 (ID)

    • Type 4SP WP 450 to 400 Bar size 3/8 to (ID)

    • Type 4SH WP 420 Bar to 280 Bar size to 2 (ID)

    • Type R13 & R15 WP 400 to 420 Bar size 1 ID & 1 Hoses.

    • Type Jack Hose 1000PSI ID with QRC

    • Type BOP Hose 6000PSI size 1 ID Hose (WRS)


    Hydraulic Hose construction

    The hydraulic hose typically consists of at least three parts: an inner tube that carries the hydraulic fluid, a layer for reinforcement, and outer layer the protective.


    The inner tube should have some flexibility and needs to be compatible with the type of hydraulic fluid it will carry. Normally used compounds include synthetic rubber, PTFE, called as Teflon and thermoplastics. The reinforcement layer comprises of one or more sheaths of braided wire, spiral-wound wire, or textile yarn. The outside layer is often weather-, oil-, or abrasion-resistant, depending upon the type of environment the hose is designed and to be used for:



    • flexing the hose to less than the specified minimum bend radius

    • operating the hydraulic system above maximum or below minimum temperature

    • exposing the hose to rapid or transient rises (surges) in pressure above the maximum operating pressure, and

    • Intermixing hose, fittings, or assembly equipment not recommended as compatible by the manufacturer or not following the manufacturer's instructions for fabricating hose assemblies.

    • twisting, pulling, kinking, crushing, or abrading the hose


    Selecting the proper Hose

    Below are seven recommended steps the system designer should follow during the hose and coupling selection process. To help determine the proper hose for an application, use the acronym STAMPED - from Size, Temperature, Application, Materials, Pressure, Ends, and Delivery. Here is what to consider in each area:


    Size - In order to select the proper hose size for replacement, it is important to measure the inside and outside hose diameters exactly using a precision-engineered caliper, as well as the length of the hose. Hose OD is particularly important when hose-support clamps are used or when hoses are routed through bulkheads. Check individual hose specification tables for ODs in suppliers' catalogs. When replacing a hose assembly, always cut the new hose the same length as the one being removed. Moving components of the equipment may pinch or even sever too long a hose. If the replacement hose is too short, pressure may cause the hose to contract and be stretched, leading to reduced service life.


    Changes in hose length when pressurized range between +2% to 4% while hydraulic mechanisms are in operation. Allow for possible shortening of the hose during operation by making the hose lengths slightly longer than the actual distance between the two connections.


    Temperature - All hoses are rated with a maximum working temperature ranging from 200 to 300 F based on the fluid temperature. Exposure to continuous high temperatures can lead to hoses losing their flexibility. Failure to use hydraulic oil with the proper viscosity to hold up under high temperatures can accelerate this problem. Always follow the hose manufacturer's recommendations.


    Exceeding these temperature recommendations can reduce hose life by as much as 80%. Depending on materials used, acceptable temperatures may range from -65 F (Hytrel and winterized rubber compounds) to 400 F (PTFE). External temperatures become a factor when hoses are exposed to a turbo manifold or some other heat source.


    When hoses are exposed to high external and internal temperatures concurrently, there will be a considerable reduction in hose service life. Insulating sleeves can help protect hose from hot equipment parts and other high temperature sources that are potentially hazardous. In these situations, an additional barrier is usually required to shield hydraulic fluid from a potential source of ignition.


    Application - Will the selected hose meet bend radius requirements? This refers to the minimum bend radius (usually in inches) that a hydraulic hose must meet. Exceeding this bend radius (using a radius smaller than recommended) is likely to injure the hose reinforcement and reduce hose life.


    Materials - It is mandatory to consult a compatibility chart to check that the tube compound is compatible with the fluid used in the system. Elevated temperature, fluid contamination, and concentration will affect the chemical compatibility of the tube and fluid. Most hydraulic hoses are compatible with petroleum-based oils. Note that new readily biodegradable or green fluids may present a problem for some hoses.


    Pressure capabilities - Hose working pressure must always be chosen so that it is greater than or equal to the maximum system pressure, including pressure spikes. Pressure spikes greater than the published working pressure will significantly shorten hose life.


    Hose ends - The coupling-to-hose mechanical interface must be compatible with the hose selected. The proper mating thread end must be chosen so that connection of the mating components will result in leak-free sealing.




View Complete Details

Hydraulic Power Packs / Units

Hydraulic power packs/units are stand-alone equipment / devices, in comparison to a built-in power supply system for a hydraulic machinery. Some hydraulic power packs are large in size, stationary type units and others are more portable.


Power packs have a hydraulic fluid reservoir / tank, which stores the hydraulic fluid, flow / pressure regulators that allow users to control the amount of hydraulic fluid pressure the power pack delivers to a hydraulic system: valve, pressure supply lines and relief lines, a pump and a motor to power the hydraulic pump.


EmiratesGreen offers the Hydraulic Power Packs for variety of applications



  1. Hydraulic Power Pack for hydraulic system for winch operation.

  2. Hydraulic Power Pack for Crane Operation for lifting load at different points.

  3. Hydraulic power Pack for flushing rigs units.

  4. Hydraulic Power Pack for Operation of jacks.

  5. Hydraulic Power Pack for controlling different operation at a time.

  6. Hydraulic Power Pack for to make system easy & increase efficiency of system.

  7. Hydraulic Power Pack for marine

  8. Hydraulic Power Pack for Marine Dredger & Marine Vessel.

  9. Hydraulic Power Pack for Marine Loading Arm & Marine Gangway System.

  10. Hydraulic Power Pack for Steel Industry.



Design Components of Hydraulic Power Pack


Hydraulic power units/packs typically offer a range of valve connections, allowing hydraulic systems users to connect them to a control valve or valves to power a variety of machines or users. The hydraulic power pack supplies hydraulic power through a control valve to run another machine.


Some of the standard components of hydraulic power packs includes:



  • Accumulator

  • Motor Pump

  • Storage Tank

  • Oil Filter

  • Coolers and Heater (Heat Exchanger)

  • Power Unit Controllers/ Regulator


To better understand the operating & design features in a hydraulic power units or systems, please visit Hydraulic System.


Hydraulic power packs requires regular repair and maintenance to increase their operational life and to have safe operation so hydraulic power packs. Hydraulic power packs maintenance includes inspection and checking the tubing against dents, cracks or other problems, replacement of the hydraulic fluid and inspection and checking the hydraulic reservoir for corrosion or rust.

View Complete Details

Hose Cutting Machine

EmiratesGreen offers good quality and robust hose cutting machines and safe operations. We offer features like reduced vibration, durability and low maintenance expenses. Low power consumption.





We offer types such as follows:




  1. For mobile van applications: Hose Cutting Machines with Battery Operated Type.

  2. For workshop applications: Hose Cutting Machines with 220V-3 power supply.



Battery Operated Cutting Machines



Application Normally can be used only up to 1 Hose with 2 x 4 wire braided type.Hose cutting should be done carefully. Proper positioning of hose before and during cutting process is very important.



Workshop Application Cutting Machines



These are heavy duty machines which can cut hoses up to 2 or large size hoses. Such hose cutting machines are normally operated by 220 AC power Supply.



The hose cutting machines are available with stainless steel cutting blades also.



Hydraulic Hoses


Hydraulic hose provides a basic means for transferring hydraulic fluid from one component to another in hydraulic system, and at the same time it provides an inherent versatility to hydraulic systems designers.



To consider hydraulic system hose is an important part of a hydraulic system is a huge understatement. The flexibility of hose enables hydraulic systems components to be positioned/located in the most efficient or convenient places, due to the fact that hydraulic hose has the ability to bend around corners, through tight spaces, or across long distances.





EmiratesGreen offers range of hoses for hydraulic systems applications/uses:




  1. Single wire Hydraulic Hose with type R1. Sizes from to 2 WP 225 to WP 40 Bar (Approx.).

  2. Double wire Hydraulic Hoses with type R2. Sizes from ID to 2 ID WP 400 Bar to 80 Bar.

  3. Hydraulic Hoses with 4 wire with WP to 280 Bar sizes as follows:

    • 4SH to 2 = 420 Bar to 280 Bar.

    • 4Sp 3/8 to = 450 Bar to 400 Bar.

    • Hydraulic Spiral Hoses with sizes 3/8 to 4SP type with flexible bending radius.

    • Hydraulic Spiral Hoses with Steel Hard wire with sizes to 2 WP 420 Bar to 280 Bar.

    • More than 400 Bar Hose for 1 inch size can be arrange against order R13/R15.



  4. Hydraulic Hoses with BOP Application.

    • Hydraulic Hose with WP Pressure 6000 PSI with factory assembled fittings with ABS/ Type Approval Certification for completely Assy.Approx. Length 100 Feet with WPT (M) fitting in SS316 fitting at both ends.



  5. Hydraulic Hose for Jack Lifting Application.

    • Jack Hose 790 Bar with Carbon Steel & SS316 fittings at both ends.If required QRC available separately provided for Assy.



    Hydraulic Hoses Types

    • Type R1 WP 225 to 40 Bar size to 2 *(ID)

    • Type R2 WP 400 Bar to 80 Bar size to 2 (ID)

    • Type 4SP WP 450 to 400 Bar size 3/8 to (ID)

    • Type 4SH WP 420 Bar to 280 Bar size to 2 (ID)

    • Type R13 & R15 WP 400 to 420 Bar size 1 ID & 1 Hoses.

    • Type Jack Hose 1000PSI ID with QRC

    • Type BOP Hose 6000PSI size 1 ID Hose (WRS)


    Hydraulic Hose Construction

    The hydraulic hose typically consists of at least three parts: an inner tube that carries the hydraulic fluid, a layer for reinforcement, and outer layer the protective.


    The inner tube should have some flexibility and needs to be compatible with the type of hydraulic fluid it will carry. Normally used compounds include synthetic rubber, PTFE, called as Teflon and thermoplastics. The reinforcement layer comprises of one or more sheaths of braided wire, spiral-wound wire, or textile yarn. The outside layer is often weather-, oil-, or abrasion-resistant, depending upon the type of environment the hose is designed and to be used for:



    • flexing the hose to less than the specified minimum bend radius

    • operating the hydraulic system above maximum or below minimum temperature

    • exposing the hose to rapid or transient rises (surges) in pressure above the maximum operating pressure, and

    • Intermixing hose, fittings, or assembly equipment not recommended as compatible by the manufacturer or not following the manufacturer's instructions for fabricating hose assemblies.

    • twisting, pulling, kinking, crushing, or abrading the hose


    Selecting the Proper Hose

    Below are seven recommended steps the system designer should follow during the hose and coupling selection process. To help determine the proper hose for an application, use the acronym STAMPED - from Size, Temperature, Application, Materials, Pressure, Ends, and Delivery. Here is what to consider in each area:


    Size - In order to select the proper hose size for replacement, it is important to measure the inside and outside hose diameters exactly using a precision-engineered caliper, as well as the length of the hose. Hose OD is particularly important when hose-support clamps are used or when hoses are routed through bulkheads. Check individual hose specification tables for ODs in suppliers' catalogs. When replacing a hose assembly, always cut the new hose the same length as the one being removed. Moving components of the equipment may pinch or even sever too long a hose. If the replacement hose is too short, pressure may cause the hose to contract and be stretched, leading to reduced service life.


    Changes in hose length when pressurized range between +2% to 4% while hydraulic mechanisms are in operation. Allow for possible shortening of the hose during operation by making the hose lengths slightly longer than the actual distance between the two connections.


    Temperature - All hoses are rated with a maximum working temperature ranging from 200 to 300 F based on the fluid temperature. Exposure to continuous high temperatures can lead to hoses losing their flexibility. Failure to use hydraulic oil with the proper viscosity to hold up under high temperatures can accelerate this problem. Always follow the hose manufacturer's recommendations.


    Exceeding these temperature recommendations can reduce hose life by as much as 80%. Depending on materials used, acceptable temperatures may range from -65 F (Hytrel and winterized rubber compounds) to 400 F (PTFE). External temperatures become a factor when hoses are exposed to a turbo manifold or some other heat source.


    When hoses are exposed to high external and internal temperatures concurrently, there will be a considerable reduction in hose service life. Insulating sleeves can help protect hose from hot equipment parts and other high temperature sources that are potentially hazardous. In these situations, an additional barrier is usually required to shield hydraulic fluid from a potential source of ignition.


    Application - Will the selected hose meet bend radius requirements? This refers to the minimum bend radius (usually in inches) that a hydraulic hose must meet. Exceeding this bend radius (using a radius smaller than recommended) is likely to injure the hose reinforcement and reduce hose life.


    Materials - It is mandatory to consult a compatibility chart to check that the tube compound is compatible with the fluid used in the system. Elevated temperature, fluid contamination, and concentration will affect the chemical compatibility of the tube and fluid. Most hydraulic hoses are compatible with petroleum-based oils. Note that new readily biodegradable or green fluids may present a problem for some hoses.


    Pressure capabilities - Hose working pressure must always be chosen so that it is greater than or equal to the maximum system pressure, including pressure spikes. Pressure spikes greater than the published working pressure will significantly shorten hose life.


    Hose ends - The coupling-to-hose mechanical interface must be compatible with the hose selected. The proper mating thread end must be chosen so that connection of the mating components will result in leak-free sealing.




View Complete Details

Hose Reels

A Hose Reel is a cylinder-shaped spindle made of either fiberglass, metal, or plastic and is used for storing a hose in manner suits to its applications. The common styles/types of hose reels are spring driven (self-retracting), hand cranked/manipulated, or motor driven. Hose reels are classified by the length and diameter of the hose they retain or used for, the pressure rating and the rewind method. Hose reels can either be fixed in a permanent location or portable or attached to: wall, a truck, cart or trailer.



EmiratesGreen offers variety of Hose Reels for variety of applications in industry.



  1. Pneumatic Hose Reel for workshop applications.

  2. Pneumatic Hose Reel general purpose applications.

  3. Air/water Reel for workshop as well as Automobile Service Centre applications.

  4. Pneumatic Hose Reel installation for aircraft service with air dryer unit & compressor with pre - filter and after filter lines.

  5. Pneumatic Hose Reel for assembly line in automobile workshop & garage station.

  6. Lube oil Hose Reel on mobile workshops.

  7. Lube oil Hose Reel on service station.

  8. Lube oil Hose Reel at service centre with Vertical & horizontal mounting.

  9. Hose Reel for mobile lube oil tankers.

  10. Hose Reel for offshore application with body material SS316.


Hose Reel Specific Applications


Below are some of the applications of Hose Reels:



  1. Hose Reel for Hydraulic Oil applications for High Pressure make with Koreel-Euorpe.

  2. Hose Reel for Custom Design for Length 15 Mtr with 1 Size Industrial Application (Air / Water & Chemical).

  3. Hose Reel for Lubrication Service Van with Grease Pump, Air Compressor with Diesel Engine Operated.


The Fire hose reelsare used by a large number of industries and normally located in buildings and business or industrial premisesfor fire protection reasons.Such hose reels are designed to provide a controlled water supply to suppress any possible fire risk that involves Class A combustible solids.Several mounting options/methods and flow controls are available from the range to match any application. Hose Reels can be supplied with or without hose and a full range of accessories are offered as separate.

View Complete Details

Hydraulic Valves

Hydraulic valvesare a vital feature of hydraulic power systems. They regulate the flow and pressure of water or oil in the systems. Valves also control volume of fluid that flows through the system. This helps to sustain a balanced state of power dynamics in various mechanical systems. Different types of valves can be used in a single system. Each type of valve is designed to perform some specific activity which contributes to the overall smooth operation of the unit. Hydraulic valves can be broadly divided into three categories. These are the flow control, pressure and directional valves.


Flow Control Hydraulic Valves

These valves monitor and regulate the rate at which fluids flow in hydraulic systems. The valve is designed to react to fluctuations in pressure within a circuit. When the pressure attains a certain level, the valve will shut or open based on the setting. This relieves high pressure where it occurs in a system. In this way, a balance is attained with other parts of the system. When a mechanical system is not operational, the flow valves prevent the flow of water under the influence of gravity. The valves keep water in a standby mode which prevents its flow within the system. Flow dividers are a type of flow control valve. They receive fluid from one flow source but divide the flow into two or more outputs in a mechanical system. The flow divider may deliver the resultant flows in equal flow rates or maintain a different rate for each output flow.


Pressure Hydraulic Valves

These regulate the pressure of water as it flows through hydraulic systems. They help to keep the pressure of water below the set limit. Pressure valves also maintain the desired pressure in part of a circuit. Various types of pressure valves work in different ways to enable correct pressure in hydraulic systems. Counter-balance valves prevent hydraulic systems from extreme accelerations. This creates dynamic control within a circuit which helps to balance the system. Unloading valves are used to relieve pressure when it gets to extreme levels. Pressure regulators manage pressure fluctuations and help to stabilize water pressure. They can also be used to set the pressure at which oil will flow into a circuit. Sequence valves are designed to detect pressures besides the maximum pressure in a system. This enables them to determine the sequence of hydraulic operations. They can sequentially open two different sections of a mechanical system.


Directional Valves

These are designed to perform any of three actions. They direct the flow of fluid in a hydraulic system in a particular direction. They can halt or initiate the flow of fluid in a system. Directional valves can also change the direction in which a fluid flows within a circuit. Various directional valves are incorporated in hydraulic systems to enable proper flow of fluids. The check valve permits the flow of fluid in one direction but prevents a flow in the opposite direction. It can also regulate pressure. Spool valves are designed to block and allow the flow of fluid within a hydraulic system.


Types of Hydraulic Valves

  1. Ball Valve (1/4 to 2 size)

    • Two way WP = 400 Bar

    • 3-way Ball Valve = 400 Bar



  2. Direction Control Valve with single solenoid & double solenoid XXXX with 24VDC & 220 AC.

  3. Hydraulic Valve pilot operated pressure relief valve with R4V series type.

  4. Hydraulic Ball Valve with SAI flange connection at both ends WP 3000PSI & 6000Psi

  5. Hydraulic Ball Valve with L, T Type ports with carbon steel & SS316 Material.

View Complete Details

GRP Enclosure

EmiratesGreen is one of the leading GRP enclosure suppliers in Abu Dhabi, UAE. Our services and products expands to entire United Arab Emirates to serve to whole nation.


EmiratesGreen offers GRP enclosure supply and installtion

  1. GRP Enclosure supply and installation for process instrumentation & process lines instruments.

  2. GRP Enclosure for Power Transformer & Power Cabinets.

  3. GRP Enclosure Custom made as per instrumentals requirement of end user.

  4. GRP Enclosure for Instruments & Transmitters.

  5. GRP Enclosure can be installed for electrical panel.

  6. GRP Enclosure with Ventilator can be provided to meet Customer requirements.


Below are the details about GRP Enclosure

  1. GRP Enclosures are approved grade for different oil & gas & refinery applications.

  2. GRP Enclosure are provided with 6 month warranty for manufacturing defects.

  3. GRP Enclosure are with Validity of 1 Year Warranty for manufacturing Defect.

  4. The GRP Enclosures are designed and fabricated as per Customer Requirements.

  5. GRP Enclosure can be installed on different Type Of instrument without disturbing Process line.

  6. GRP Enclosures are provided with Air Ventilator for free flow.

View Complete Details

GS Load Centers For OutBack Radian

Description

OutBack Powers GS Load Centersare an integratedconnection enclosure series for AC and DC systemconnections in OutBack Radian Series inverter/chargerapplications, through provided inverter DC overcurrentprotection and disconnects, dual AC inputs, grid-tie inverterconnection and 120/240VAC or 230V maintenance bypass.


Designed for use with the Radian Series inverter/chargerfamily, the options offer solutions for ground-up custom designs or factory pre-wired configurations for specificapplications. The GSLC175-AC-120/240 can be usedwith AC-coupling applications in grid-tied systems.
The OutBack GS Load Centers simplify the configuration, distribution, and implementation of energy storage of theRadian Series inverter/charger through a standardized approach

View Complete Details

Seamless Tubing

Seamless Tubing with Griflex Sheeting

EmiratesGreen is highly experienced in its products and services and provides best possible solution to its clients make things work properly as expected yet in affordable cost. EmiratesGreenSeamless Tubing will be covered by PVC Griflex Sheeting to avoid corrosion with help of below procedure.



  • Tubing will covered by PVC Sheeting with pneumatic compressor air supply at one end of sheeting & offer end inserted to tubing, sheeting will be manually rolled over seamless tubing up to the end.

  • PVC Sheeting is avoiding corrosion thus increasing life of tubing. It also reduces maintenance cost of the overall systems.

  • Because of salty environment and offshore rig application, the corrosion rate is very high. That's why to reduce maintenance cost, PVC sheeting is very helpful for the system to protect from corrosion.

  • PVC Sheeting with printing will be done by EmiratesGreen & STD specification will be printed on it.

  • PVC Sheeting will be provided with tubing grade & HT printed on it.

  • PVC Sheeting can be provided on Coil Tubing as on Request.

  • PVC Sheeting for high temperature applications can be provided on customer request.

  • Exotic material Tubing for Gas applications (Alloy Steel Material)

    • Material Grade with 904L

    • Material Grade with 316-TI

    • Material Grade with 317L



  • Seamless Tubing for Instrumentation & Liquid Line.

    • Material Grade SS316 / SS316L.

    • Material Grade with SS 304

    • Material Grade with SS 321



  • Seamless Pipe for Cuprous - Nickel for Marine Applications.

  • Coil Tubing in 904L/ SS 316L/ SS 304 / SS321.

  • COIL TUBING with PVC sheeting by European Origin.

View Complete Details

Peacock Measuring Instruments

The Ozaki Mfg. Co., Ltd has established in 1916 and came along with Japanese Automotive industry that led the world technological evolution. We have been getting support from our valuable customers by our great pride High Accuracy and the Quality products. Moreover, our products have been used by not only Automotive industry but also a wide industries such as Machinery, shipbuilding, railway, aircraft, power plant, chemistry and construction etc.


Dial Gauges of our main products have great reputation and our brand name "PEACOCK" well-known as synonym of Dial Gauges.


A Dial Gauge which is a kind of length meter has feature that the displacement is automatically indicated by its Pointer.


The structure of "PEACOCK" Dial Gauges has simple structure which is magnified mechanics by the gear. However, the individual parts become a complete part through many processing and assembled by strict inspection.


In next 100 years, we desire that our products will have been still trusted. Hereafter, our desire will never fade away. To satisfy more various demands in the future, we concentrate to keep high quality products with characteristic production to meet top-level in advanced modern industrial world by a speedy technical improvement.


The OZAKI MFG. CO., LTD. Have never been happier so as long as making Precision Measuring Instruments that are not ashamed of the name at the "100th anniversary of founding" that will faced soon and will meet with the expectation for PEACOCK fan.

View Complete Details

Selectronic SP PRO OFF GRID POWER SYSTEM



The highly successful SP PRO Series II has been expanded to include the SP PRO GO Series designed specifically for the Solar Hybrid (grid connect) market. They have a Grid Feed-In Power Rating, independent of the inverter rating, to meet the requirements of the utility while still providing for the consumer's power needs.


Grid Feed and Grid Battery Backup in one unit

Add the versatility of energy storage to your Grid Connect solution using the SP PRO as a low voltage grid feeding inverter that puts you in control of your grid system.


Interactive Inverter Charger

The versatile SP PRO inverter can also be configured to operate as an Interactive Inverter Charger with conveniently preset configurations for use in mobile or Off Grid power systems.


Multiple Applications

The SP PRO is suitable for Grid Connect and Off Grid applications for residential, commercial, industrial, marine and mobile situations, while the SP PRO GO (Grid Optimised) is suitable only for grid connect applications.


Engineering Excellence

Drawing on our inverter experience since 1981, the SP PRO contains features not found in other inverters. With highly accurate thermal power management and high speed digital signal processing, the SP PRO sets new standards for reliability, power density and flexibility.


The SP PRO is AS4777 Approved

The SP PRO series is available in sizes ranging from 3 kW to 20 kW for a single phase system and 9 kW to 60 kW for the SP PRO in a three phase configuration. All SP PRO inverters are approved to AS4777 for grid connection in Australia and New Zealand.



View Complete Details

DC Current Shunts

A range of current shunts are available for measurement of DC coupled solar current or DC load currents.


Important note

  • A Shunt is NOT required to measure the DC current of the SP PRO inverter as this is measured internally

  • A DC shunt is NOT required to measure the solar in a AC coupled system as this is also measured internally by the SP PRO inverter



The range of DC current shunts available are as follows:



  • Current Shunt, 100A 75mV 0.5%

  • Current Shunt, 150A 75mV 0.5%

  • Current Shunt, 200A 50mV 0.5%

  • Current Shunt, 50A 75mV 0.5%

  • Current Shunt, 400A 75mV 0.5%

View Complete Details

Mobile Mounting Kit

The mobile mounting kit consists of a rubber mounting system designed to absorb the shock in a rugged mobile installation. The mobile mounting kit mounts between the inverter wall mount bracket and the wall.

View Complete Details

Grid Fail Backup Power Generator

Designed for the Grid Backup market, this model has the components required to start and control an automatic-start generator in times of low battery and grid failure.This option improves the availability of supply during long outages without the need to increase the size of the battery bank in grid backup systems.

View Complete Details

Outback Power Solar Inverter

Description

The Radian Series GS8048A and GS4048A Grid/Hybrid (full-flexibility grid-interactive/off-grid) Inverter/Charger is engineered toward one goal: making system design and installation easier and faster in grid-interactive and comprehensive off-grid applications.The new Radian Series inherit the hallmark features of theoriginal design, including: dual AC inputs for grid/generatorflexibility with no external switching required, unparalleled surgecapability and operational stability, easy field upgradeabilityand stacking capability for large system scaling, simplifiedsystem commissioning through a powerful, easy-to-useconfiguration wizard, and multi-mode operational flexibility.


In addition, both models have a new Advanced Battery Charging(ABC) profile option to support leading-edge battery technologiessuch as Lithium-Ion and others, and enhanced diagnostics forimproved performance. And both incorporate OutBacks GridZerotechnology, a superior level of intelligence in energy management forself-generation and self-consumption programs, providing precisebalancing between using stored energy, solar and utility power, blending-in the latter to overcome surges and load spikes whenneeded. GridZero operation makes it possible for a smaller inverterand battery system to perform like a much larger one when required, putting stored and renewable energy sources to work and minimizinggrid dependence. GridZero technology make the new Radians idealfor use in complex utility environments such as California and Hawaii.


The GS8048A and GS4048A are certified to UL1741 for US applications, and CSA C22.2 No. 107.1 for Canada, and is IEC 62109-1 certified tomeet the most stringent worldwide PV safety and emission standards.This product is for selected North, Central and Latin American markets.

View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • EmiratesGreen Electrical & Mechanical Trading (EmiratesGreen Electrical & Mechanical Trading)
  • P.O. Box 110507 Elite Business Zone Musaffah-44, Office No. B-51 Near Dragon Mall, Abu Dhabi, UAE
  • Share us via