Our Products #85585

Nitobond SBA is used for bonding precast concrete bridge segments to provide a structural and waterproof joint. Nitobond SBA is also suitable as a gap filling paste and for grouting of starter bars, holding down bolts, etc, where a paste consistency material is required.

Dekguard Textured is a textured water based protective coating based on a special acrylic polymer. It provides low dirt pickup, resistance to aggressive elements, UV light and rain. It is available in a wide range of colours.

High resistance to the effects of long-term weathering and durable in all climatic conditions
Allows water vapour to escape from the structure
Water based
Choice of water based or solvented primers
Wide range of decorative colours
Helps disguise patchy or unsightly substrates
Can be used in combination with Dekguard S to obtain protection against acid gases, chloride ions, oxygen and water

Nitobond AR is a modified acrylic emulsion which is specially designed for use as a bonding aid, curing agent and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external application.

Single component gauged as required.
Simply brushed onto concrete as a primer.
Provides excellent bond to concrete, masonry, stonework, plaster and block-board.
Improves tensile and compressive properties. Allows thin section applications.
Compatible with all common hydraulic cements.
Suitable for use in Middle East conditions. Used as a curing membrane.
Is economical in use.

As a multi purpose adhesive, bonding agent, primer and cement admixture.

* If there is not a datasheet relevant to your selected region you will be forwarded to make an enquiry.

Adhesive compound is an epoxy resin based products with special fine fillers. The components differ in colour thus allowing visual assessment of mixing.

Excellent adhesive
Fast cure
Chemical resistance
Easy to use

Nitobond EP is based on solvent-free epoxy resins containing pigments and fine fillers. It is supplied as a two-part material in pre-weighed quantities ready for onsite mixing and use.
Coloured components, white base and green hardener, provide visual evidence that adequate mixing is achieved.

Can be applied to dry or damp surfaces
High mechanical strength
Good positive adhesion
Can be applied where a substraterepair barrier is required
Standard and slow set grades

Nitotile EPW Grout is a three component water miscible epoxy resin tile joint filler based on new generation epoxy resin technology supplied in pre weighed packs, ready for onsite mixing and use.

Resistant to mild chemicals and acids.
Solvent free - can be used in confi ned areas.
Good resistance to abrasion and impact.
Non staining & easily cleaned.
Available in a range of attractive colours.
Resists bacterial growth.
Hygienic - suitable for use in Laboratories, Hospitals and Health centers.
Good to use in wet areas like showers, swimming pools, & bathrooms.

Nitomortar PE is a resin jointing and repair compound, based on a polyester resin system.
There are two grades. Nitomortar PE: The standard material for general purpose use.
Nitomortar PE Concrete: A special grade allowing users to add suitable aggregate, thereby substantially reducing the cost of infilling larger voids.
Winter versions of Nitomortar PE is available which are faster setting at low ambient temperatures. Both grades of Nitomortar PE are supplied as two-component products with pre-weighed
quantities of liquid resin and powdered hardener, ready for on-site mixing and use. The hardener system enables the mix to be varied from a pourable consistency to a trowellable mortar without significantly affecting the setting times or strengths achieved.

Nitobond HP is single component white, milky emulsion based upon modified acrylic type Resins. Designed for use with Renderoc HB25, Renderoc HB40 and Renderoc SPXtra.

Single component no mixing required on site
Easy to use ready to use as supplied from the container
High bond strength excellent bond strength between polymer modified mortars and concrete.
Excellent grab Nitobond HP is specially designed for optimum build of Renderoc HB25 and Renderoc HB40 In Vertical and overhead applications.
Versatile easy to use on site. Suitable for both internal and external use.
Curing aids can be used as curing membranes for Fosrocs Renderoc range.