Our Products #4258175

A. General1. Furnish and install operable partitions and suspension system. Provide alllabor, materials, tools, equipment, and services for operable walls inaccordance with provisions of contract documents.1.02 RELATED WORK BY OTHERSA. Preparation of opening will be by General Contractor. Any deviation of siteconditions contrary to approved shop drawings must be called to the attention ofthe architect.B. All header, blocking, support structures, jambs, track enclosures, surroundinginsulation, and sound baffles as required in 1.04 Quality Assurance.C. Prepunching of support structure in accordance with approved shop drawings.D. Paint or otherwise finishing all trim and other materials adjoining head and jambof operable partitions.1.03 SUBMITTALSA. Complete shop drawings are to be provided prior to fabrication indicatingconstruction and installation details. Shop drawings must be submitted within10 days after receipt of signed contract.1.04 QUALITY ASSURANCEA. Preparation of the opening shall conform to the criteria set forth per ASTME557 Standard Practice for Architectural Application and Installation ofOperable PartitionsB. The partition STC (Sound Transmission Classification) shall be achieved per thestandard ASTM E90 test method.C. Noise Reduction Coefficient (NRC) ratings shall be per ASTM C423.D. The manufacturer shall have a quality system that is registered to the ISO 9001standards.1.05 PRODUCT DELIVERY, STORAGE, AND HANDLINGA. Proper storage of partitions before installation and continued protection duringand after installation will be the responsibility of the General Contractor.1.06 WARRANTYA. Partition shall be guaranteed for a period of Two years.

The frames are of aluminumalloy 6063-T6 with extruded aluminum trim to protect the edge of the glass. All WR5000 series frames are made of thermally broken extended aluminium profile PVDFcoated to RAL color all frames steel reinforced for stability against wind pressure.Vertical interlock between panels is via deep nested tongue and groove configurationresulting in more stability, ease of panel alignment and better sound seal. Hufcor track systems have been life-cycle tested for up to 161 Km or approximately 10years of use. Track is of architectural grade extruded aluminum alloy 6063-T6 and isdesigned to provide integral support for adjoining ceiling, soffit, or plenum sound barrier.Track is triple PVDF coated to RAL color for protection. All Fixing accessories to be inarchitectural grade 316 Stainless steel. Horizontal top seals are UV stabilized continuous contact multi-ply brown while thebottom horizontal seals incorporate an extruded aluminium, box-section, mechanical sealmanually operated by a handle inserted in the panel stile. Turning the handle through 170degree simultaneously extends or retracts the seal through an overthrow cam mechanism, which firmly holds the seal in the retracted or extended mode. Top supporting horizontalrail are to be steel reinforced aluminium and incorporate sweep seals. Bottom horizontalrail to be 6063-T6 aluminium and incorporate retractable mechanical seal. The standard frame and track finish is clear anodized aluminium, however customanodizing bronze or champagne is available on request. Frames can also be powdercoated to desired RAL color. Specialty or Art glass can also be integrated with the systemas an option.Weight of the panels shall be approximately:61 Kg sq meter with sealed, double pane units 6 mm and 12 mm Clear Tempered glass Weather resistant glasswalls allow you to enjoy the outdoors through climate controlled interiors. Designed for covered external use, it forms a barrier against the weather elements whilst maintaining inside temperature and humidity levels. Frame components allow the use of single or double glazing, Additional light, glare and vision control can be achieved by the fitting of double glazed units.

Hufcor Glasswall Movable Glass Partitions that divide room and maintains an open contemporary space. Glasswall is the creative answer for facilities needing a physical, not a visual barrier. The visibility allows designers to separate space such as smoking and non-smoking areas in cafes, lounges and foyers. Glasswalls can close off store entrance after business hours or be used to guide customers to featured products within a retail store. Ideal Solutions for Office Buildings Shopping Centres Restaurants Bank Lobbies Executive Meeting Rooms Hotel Lobbies The glass is mechanically attached to top and bottom rails anddoes not rely on friction and adhesives.Weight of the panels shall be approximately 37.12 Kg per sq. m for 13.14 mm glass.SUSPENSION SYSTEMHufcor track systems have been life-cycle tested for up to 161 Km or approximately 10 years of use.FINISHESThe horizontal rails and track finish is clear anodized aluminium, however custom anodizing bronze or champagne is available on request. Frames can also be powder coated to desired RALcolor. Specialty or Art glass can also be integrated with the system as an option.QUALITY ASSURANCEA. Preparation of the opening shall conform to the criteria set forth per ASTM E557Standard Practice for Architectural Application and Installation of Operable Partitions.B. Glass shall be clear tempered per ASTM C1048-92.WARRANTYTrack, carriers, and horizontal rails shall be guaranteed for two years against defects in material andworkmanship. The glass is not included in this warranty.

Fully automated vertically rising acoustic folding partition system The Skyfold auto lift wall system is an electrically operated vertically folding operable wall. It stores conveniently in the ceiling and when deployed, forms a hard, rigid and flat wall. Work Included1.1.1 Supply and installation of Automatic Vertically Folding Acoustical Wall(s) asshown on the architectural drawings. All necessary hardware, seals, liftingmachinery, electrical controls are included.1.2 Related Work(NOT INCLUDED)1.2.1 The main support steel beam for the wall, as well as the miscellaneous supportsteel for the lifting machinery for the Automatic Vertically Folding Acoustical WallSection .1.2.2 Ceiling storage pockets along axis of Automatic Vertically Folding Acoustical WallSection .1.2.3 Bulkheads and sound insulation above, below, and in the fixed walls at both endsof the Automatic Vertically Folding Acoustical Wall, as per ASTME557- Section .1.2.4 All site wiring and connections for main power, including disconnect switches ateach motor location. All site wiring and connections for control, includinginstallation of key switches Section .1.3 System Description1.3.1 Definition1.3.1.1 Automatic Vertically Folding Acoustical Wall (from here on calledOperable Wall) shall refer specifically to acoustical partitions that, when in the down position (closed) are hard, rigid, flat, plumb walls, made of a grid of rectangular acoustical panels, and when are lifted(opened), fold upward (vertically) without the use of any manual labor, in a manner similar to an accordion, into a pocket in the ceiling, between roof joists, or up between built in bulkheads. In the down(closed) position, the wall shall be comprised of two vertical planes ofacoustical panels, separated by an acoustical air space.The operable wall shall open and close in a manner similar to anaccordion, in that all wall panels fold and unfold at the exact sametime, at the exact same rate. Walls that rely on the sequential foldingof acoustical panels or acoustical panel sets are not acceptable.There are two types of drive systems available for the operable wall:Compact Drive System:The motor assembly is mounted directly above the centre line of theoperable wall. Support steel is only required at one location. Used forwalls up to 36-0 (11, 000mm) finished ceiling.

Modular panel size in standard program 1200mm width.(other modulations upon request) Aluminium profiles: Silver anodized or RAL powder-coated. Acoustic rating: From 41 to 47dB Rw.DESIGN CONFIGURATIONPartition with extruded aluminium frame (RAL powder coated or silver anodised).Solid vertically connected with frames or concealed frames (hairline between panels or suspended panels).Solid supported by 35mm high U-track at top and bottom .Correction of uneven floor and ceiling levels upto 12.5mm

High Pressure Solid Grade Compact Laminate(HPL) is a Flat Panel Based onThermosetting Resins, Homogeneously Reinforced with Wood Fibers andManufactured Under High Pressure and Temperature, UV Resistant, WeatherResistant, Moisture Resistant, Resistant To Extreme WeatherFluctuations and is Fire Retardant.Benches support frames are made of high quality gravity die cast aluminum 6m conforming to BS 1490. Support frame finish: die cast aluminum polyester powder coated to BS 6496 to standard RAL colours . Bench seats and backrest are made of 13-mm thick high-pressure compact laminate. All fixing bolts and screws are stainless steel.Benches support frame made of high quality grade steel box section. Hot-dipped galvanized, support frame finish, spray painted to colour black, RAL 9011. Bench seats and backrest are made of 13-mm thick high-pressure compact laminate. All fixing bolts and screws are stainless steel.

Partition with extruded aluminium frame (RAL powder coated or silver anodised).6-8-10mm thick framed double glazing (toughened, laminated glasses), any type of sandblasting, decorative films upon request.Possible integration of venetian blinds.Glazing vertically connected with frames.Glazing supported by 35mm high U-track at top and bottom .Correction of uneven floor and ceiling levels upto 12.5mm.Modular panel size in standard program 1200mm width.(other modulations upon request)Aluminium profiles: Silver anodized or RAL powder-coated. Acoustic rating: From 41 to 42dB Rw.

GIBCA has developed a Locker System suitable for all contract locations with the intelligent combination ofperfect function and design. GIBCA Lockers are manufactured using solid grade high-pressure compact laminate. SPECIFICATIONS: Locker side, divider, top & bottom panels made of 1013 mm High Pressure Compact Laminate. Locker back panel made of 6mm MDF Finish, film faced (white). Locker door panel made of 13mm High Pressure Compact Laminates. Reinforced works made of high quality extruded aluminum. Finish: Silver anodized. Option Polyester powder coated finish to standard RAL colours. Hardware: Camlock set, Hanger rod, Engraved numbering, Coat hook.Standard steel base: 160mm high. Made from steelbox section, polyester powder coated to RAL 9011(black) with adjustable feet.Locker shutters: 13mm thick Solid Grade HighPressure Compact Laminate.Available in over 75 colors from the Gibca colorselector.Locker side panels: Top, dividers and bottom (madeof 13mm solid grade compact laminate in whitecolor). Back panel made of 6mm thick whitemelamine faced MDF6mm Compact Laminate.Comes with standard hardware includes a cylinderlock with master key system, chrome plated hangerrod and coat hook, PVC ventilator andpermanently engraved system.

An acoustic or sound baffle is a device which is designed to muffle or at least greatly reduce noise. A sound baffle is usually made from thick, absorbent material. This material does not allow sound waves to penetrate it as readily, and it also prevents the waves from bouncing back to the source. An acoustic baffle can also be used to improve the quality of acoustics.