Post Buy Requirement
IT
United Arab Emirates
Add Review

Other Products / Services

Automatic Tube Making Machine

  • Rated Power 16.5KW
  • Water Supply 190 liters /hr
Mainly used to weld a roll of stainless steel strip into a tube.

FUNCTIONS :
1. The frame of machine is made of excellent steel plate and of stable structure.

2. PLC automatically controlled, human-computer interface.

3. Control the speed by Mitsubishi transduction. The tube making speed can be adjustable.

4. Any error, abnormity or lack of material, the machine will alarm automatically.
View Complete Details

Automatic Tube Cutting Machine

  • Power suppiy Triphase 380V, 50Hz
  • Rated Power 1.6KW
  • Air supply 5 -7kg/cm2
1. PLC controlled automatically, load and cut material automatically.

2. Two kinds of sawblade speed, pneumatic convert to hydraulic and the speed of sawblade is adjustable.

3. V-shaped collets move at the same time. ( 8.0mm tube, clamp 25pcs at a time)

4. Tube length after cutling: 200mm - 2300mm

5. Jaw opening: 1OOmm
View Complete Details

Straightening Machine

  • Rated Power 1.5KW
  • Power supply Triphase 380V, 50Hz
  • Applicable tube diameter Φ5mm - Φ21mm (over this range can be custom-made)
Is used to straighten kinds of annealed tubes or rods.

FUNCTIONS :
1. The height and angle of rollers are adjustable, can satisfy kinds of specifications.

2. Adopts hyperboloid roller design which can improve the surface and roundness of tubes.

3. Six durable alloy tool steel rollers.

4. Easy to operate.
View Complete Details

Automatic Tube Turning Machine

  • Power supply Triphase 380V, 50Hz
  • Rated power 1.6KW
  • Air supply 5 -7kg/cm2
Is used to turn the tube ends according to the preseted length. chamfer and dig the powder of tube ends automatically.

FUNCTIONS :
1. PLC automatically controlled, human-computer interface. One man can operate three or four machines simultaneously.

2. The elements are automatically loaded, and then centered so the same amount will be cut from each end, thus ensuring that the original length can be maintained.

3. Show how to clear the error automatically.
View Complete Details

Tube Rolling Machine

  • diameter Φ5.2mm - Φ19.0mm
  • length 110mm
  • Efficiency 18m/min
.The frame of this machine is made out of pig iron casting. The rocker die and tank are integral linear cutting. This machine is also equipped with fine-tuning dial, automatically removing sundries device and automatically cooling system.

2. According to the tube size and your special requirements, we have two types of motor of pinch roller for your choice. They are non-uniform speed (different speed) and uniform speed. The former make the tube better ductility, while the latter applies 10 the lube with large diameter.

3. When the tube specifications changed, we only need to replace a set of pinch rollers. The pinch rollers can be classified into two categories: high speed steel and tungsten carbide alloy.

4. Automatically stop when clogging.

5. This machine is of small size, low noise, convenient adjustments.

6. Applicable tube: Copper, iron, aluminum, stainless steel, etc.
View Complete Details

Automatic Soldering Machine

  • Power 25KW, 30KW, 40KW, 60KW
  • Power suppiy tri-phase 380V 50Hz
  • Air supply 4-6kgf/cm2
It is mainly used for welding the round Pot woth dia 250 to 500mm and square pot with dia300 to 500mm

FUNCTIONS :
1. Application range: electric kettle, coffeepot. fryer and other products.

2. 0peration mode: manual time control.

3. Small size, compact in structure, easy operation and good design.

4. High production, stable performance, good welding. It can work 24hours continuously.

5. It can also equip with whole set cooling system (including water tank, pump and corresponding spare part)

6. Air supply control to avoid pot deforming for heating. It can make the weld joint better and better quality
View Complete Details

Semi Automatic Turning Machine

  • Power supply Triphase 380V, 50Hz
  • Rated power O.8KW
  • Air supply 5 -7kg/cm2
mainly used to turn the ends of compressed tubes, and also can be used to turn and chamfer all kinds of tubes and rods in the hardware industry.

FUNCTIONS :
1. Pneumatic clamping and feeding.

2. Cutter rotate while the element not. safe and convenient operation.

3. Hydraulic speed governor control the turning speed, stable quality.
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • Khurram Salah (impex trading)
  • dubai, United Arab Emirates
  • Share us via