Post Buy Requirement
IR
United Arab Emirates
Add Review

Our Products

Epdm

  • Tensile Strength 10.5 MPa Min
IRC Moulded Rubber Products comprise wide range of Polymer use, i.e. EPDM, Neoprene, Nitrile, SBR and NR. Compounding is done to meet relevant BS, DIN and ASTM Standards to achieve best performance.
Production of Rubber Moulded Products is done by Compression and Transfer Moulding process followed by automatic Deflashing.
In the Transfer Moulding process rubber compound is transfered under pressure into the mould cavity and allowed to fill the cavity obtaining the shape of the mould and cross-linked by using the platen temperature, finally product is formed in the required shape. In compression Moulding process compound is pressed under sufficient hydraulic pressure to obtain mould cavity shape and compaction while curing process in progress.
View Complete Details

Vulcanized Frame

  • Tensile Strength 10.50 MPA Min
Vulcanized EPDM Corner Jointed Gaskets and Vulcanized Picture Frame Gaskets offer excellent corner Sealing against water and dust seepage and provide good thermal insulation for cost saving on air conditioning. The corner is the weakest point in the Aluminium System as all Sections are cut and matched to obtain desired angle. The joint is thus prone to allow water seepage due to gap between joint profiles. The vulcanized corner jointed EPDM Rubber gaskets provide perfect Sealing to such joints and avoid needs to fill sealant. Thus a clean performing joint is achieved.
The modern method of producing complex profiles with corner joints involves:
1. Production of accurate profiles in a continuous vulcanizing line.
2. Moulding of corners and joining of profile ends to make a complete gasket frame by Transfer Moulding techniques.
In this process the desired profile is Extruded, Cured and before Moulding of corners is cut to controlled length using a cutting gauge.
In the Transfer Moulding process the profile geometry is matched to the moulded cornerend requirements. Rubber compound is injected under pressure into the mould cavity and allowed to vulcanize, obtaining the shape of the mould and cross-linking the profile edges to the moulded jointed area. Thus a continuous and homogeneous gasket is formed.
View Complete Details

Setting Blocks

  • Material Elastomer EPDM Synthetic Rubber
  • Function Setting Blocks and Hard Profiles
International Rubber Co. has developed special compound for Hard EPDM Rubber Profiles and Setting Blocks to suit all major Aluminium systems used in Middle East Region. With in-house Tool Room and R & D facilities, the response time to new Developments is very short.
View Complete Details

Water Stops

Supplied in coils as per site requirements, which are easily handled, flexible and may be bent around corners or formed in curves as re-quired.
Can be spliced in the site according to the desired designs, thermostati-cally controlled, electric splicing irons.
Installing holes could be added at the installation area, it could facilitate fixed with adjacent reinforced, and not produce shifting.
PVC and TPE water stop are eco friendly recyclable and materials.
Can be produced in a different thicknesses
View Complete Details

Silicone

  • Hardness (Shore A) 60±5 ºA
IRC Moulded Rubber Products comprise wide range of Polymer use, i.e. EPDM, Silicone, Neoprene, Nitrile, SBR and NR. Compounding is done to meet relevant BS, DIN and ASTM Standards to achieve best performance.
Production of Rubber Moulded Products is done by Compression and Transfer Moulding process followed by automatic Deflashing.
In the Transfer Moulding process rubber compound is transfered under pressure into the mould cavity and allowed to fill the cavity obtaining the shape of the mould and cross-linked by using the platen temperature, finally product is formed in the required shape. In compression Moulding process compound is pressed under sufficient hydraulic pressure to obtain mould cavity shape and compaction while curing process in progress.
View Complete Details

Water Proofing Membrane

  • Colour Balck
Water proof or water-resistant describes objects relatively unaffected by water or resisting the ingress of water under specific conditions. In building construction a structure needs water proofing since concrete itself will not be watertight on its own but note concrete is easily waterproofed with additives etc. The conventional system of water proofing involves membrane that act as a barrier between water and the building structure preventing the passage of water.
View Complete Details

Bridge Bearing Pad

Bearings are devices which transmit the load from the superstructure to the substructure and to accommodate movements and displacements. Bearings are built to withstand loads and simultaneous deformation in any direction, while also allowing for minor rotations in any of the bearing's axes. IRC bearings can be made entirely of rubber or can be reinforced with special sheet steel to increase capacity and transversal strength.
View Complete Details

Pipe Seals

IRC produces over 300 different pipe seals using number of different compounds, such as EPDM, NBR, SBR, CR and Natural Rubber etc., all of which meet specifications related to shape and material.
IRC provides a durable cost effective solution to sound jointing, whatever the application. Sophisticated and flexible techniques ensure optimum cost and consistent quality in both small and large volumes.
View Complete Details

Automotive Seals

International Rubber Company also deals with automobile industry, such as car door seals which are co extruded & comes with Steel embedded. IRC also provides with any size depending on customer requirement.
Product Application
These kinds of gaskets are used for weather sealing, Sound proofing, & Antifriction glass movement for window.
IRC also provides complete solution for car type seals as you can see that Door Mounted Weather Seal used in car door for sound proofing & weather sealing application
View Complete Details

Structural Glazing Tape

Structural silicone systems for glazing and cladding require compatible spacers to achieve reliable performance of the silicone adhesives. Structural Glazing Tapes is the most widely used spacers for structural silicone systems. They are also known as spacer tapes, which are available in a wide variety of sizes to accommodate typical silicone joint designs. And, in addition to holding the glass or cladding at a predetermined distance from the substrate for proper silicone joint design, they also offer a number of other benefits, including compatibility with other silicone sealants, a special adhesive surface, curing of sealants, a special formulation and thermal resistance.
Many brands are available in market but International Rubber Company deals with well known brand in the market which are Norton by (Saint- Gobain) & Vito from Germany, as they are well known by the faade industry.
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • Rafik Shaikh (International Rubber Company)
  • Po Box 27140, United Arab Emirates
  • Share us via