National Plastic L.L.C Sharjah

CPVC for domestic and industrial hot and cold water applications in sizes upto 16" (400mm). CPVC is suitable for conveying pressurized hot fluids upto 90°C. Pipe can be supplied in ASTM or Metric / ISO dimensions and a full range of CPVC fittings / transition fittings are available. Special Solvent Cement manufactured by IPS Weldon for high pressure / high temperature applications is also available. Benefits of CPVC CPVC is the most superior plastic alternative to Polypropylene, PEX, Polyethylene and other plastic and much more superior to metal alternatives with respect to. Heat resistance up to 90˚C Chemical resistance over a broad temperature range Long term proven service performance of more than 50 years Lower installed cost Suitable for potable water and can be produced with NSF or WRAS approved grade Does not sustain burning

UPVC well casing and screen in compliance with the DIN 4925 standard from 1 1/4" to 16" (36mm - 400mm). A shallow depth and deep well depth range cover most applications of ground water extraction. National Plastic also produces ribbed borewell / screen. A full range of imperial and ASTM sizes are also available upto 16" (400mm). All the accessories required for the proper installation of well casing and screen including lifting heads, casing clamps, centralizers, sand traps, bottom / top caps and reducer fittings. Accessories are available to suit the full range of sizes produced.  

HDPE, LDPE and LLDPE pipe systems in a range of sizes and specifications from 1/2" to 4" (13mm - 110mm). Polyethylene pipe is used for water supply, irrigation systems, plumbing connections, gas distribution and drainage. A full range of insert electrofusion, butt welded and compression fittings to suit all National Plastic polyethylene pipes are available.    

A full range of UPVC and CPVC fittings to the main International Standards of EN1452, BS3505, DIN8063 and ASTM D2466 including sizes from 1/2”-16” (16mm- 400mm). The fittings include solvent weld joints and are fully compatible to the National Plastic pipe range. Specially fabricated fittings and long radius bends can be supplied on request along with rubber ring joints on certain sizes in the range. Fittings are available in standard colours of light grey, dark grey and white and suitable for all pressure applications.  

National Plastic produces a wide range of UPVC Pressure Pipes to most of the major international standards and dimensions of Metric and Imperial. The pipes are made from 100% virgin UPVC resin and have a minimum required strength MRS=25 mpa so that the pipes meet or exceed the rigorous hydrostatic requirements of the standards. The pipes are produced in a range of colours such as grey, white, blue, purple and carry full printing and identification at 1m intervals according to the standard requirements. Pipes can be supplied with integral solvent weld joints along with Weldon 717 cement or rubber ring joints using high performance EPDM seals to EN681. The joints exceed the pressure rating of the pipe and can therefore cover all the applications where the pipes are installed. All pipes produced fall under an ISO 9001:2008 Quality Assurance system and several ranges carry third party verification such as the BSI Kitemark or WRAS certification so customers are assured the pipes are of the highest quality. For export requirements pipes can be supplied in 5.8m (19ft) lengths so they can be loaded into containers without damaging sockets. National Plastic pressure pipes have been operating in demanding conditions for almost 40 years now (See the Worldwide Projects List) and is proof of their outstanding quality and serviceablility.

National Plastics produces a range of upvc schedule 40 ducts in sizes 1/2" to 6" that are in accordance with NEMA TC-2A standard and listed to UL 651. The conduits are suitable for above or below ground installations and made from 100% virgin pvc resin. The ducts meet and exceed all the mechanical and performance requirement of both the NEMA TC2 and UL 651 standards. General Properties Fully compliant to NEMA TC-2 and UL 651 Rated for use with 90oC conductors Ultraviolet protected High impact and deformation properties Solvent cement joints with deep sockets Can be supplied in various lengths such as 3m, 6m, 2.9m, 5.8m (standard leg lengths 3m, 6m) Smooth solid wall Produced under an ISO 9001:2008 Quality Assurance System