Post Buy Requirement
PE
United Arab Emirates
Add Review

Our Products

  1. Soldering Equipment 7 Products available
  2. Hand Tool Kit 3 Products available
  3. Others 52 Products available

Other Products / Services

Temperature Sensor Module

  • Operating Voltage 3.0V to 5.5V
  • Temperature Measurement Range -55°C to 125°C [-57°F to 257°F]
  • Measurement Accuracy Range ±0.5°C
  • Dimensions 18.5mm x 15mm [0.728in x 0.591in]
P-001: Temperature sensor module
Arduino Temperature Sensor Module PE-001, Allows ambient temperature measurement using digital serial bus.




Specifications

The PE-001 Temperature Sensor Module consists of a DS18B20 single-bus digital temperature sensor, a LED and a resistor. Compatible with popular electronics platforms like Arduino, Raspberry Pi and Esp8266.



View Complete Details

Training Project With USB Cable

  • Microcontroller ATmega2560
  • Operating Voltage 5V
  • Input Voltage (recommended) 7-12V
  • Input Voltage (limit) 6-20V
  • Digital I/O Pins 54 (of which 15 provide PWM output)
  • Analog Input Pins 16
  • DC Current per I/O Pin 20 mA
  • DC Current for 3.3V Pin 50 mA
  • Flash Memory 256 KB of which 8 KB used by bootloader
  • SRAM 8 KB
  • EEPROM 4 KB
  • Clock Speed 16 MHz
  • LED_BUILTIN 13
  • Length 101.52 mm
  • Width 53.3 mm
  • Weight 37 g
Arduino MEGA 2560
Training Project with USB Cable
View Complete Details

Infrared Transmitter Module

  • Operating Voltage 5V
  • Forward Current 30 ~ 60 mA
  • Power Consumption 90mW 90mW
  • Operating Temperature -25°C to 80°C [-13°F to 176°F]
  • Dimensions 18.5mm x 15mm [0.728in x 0.591in]
P-005: Infrared Transmitter module
Arduino IRTransmitter Module PE-005, emits infrared light at 38kHz.


Specifications

The PE-005 Infrared Transmitter Module consists of just a 5mm IR LED. It works together with the PE-022 IR receiver module. Compatible with popular electronics platforms like Arduino, Teensy, Raspberry Pi and ESP8266.



View Complete Details

Active Piezo-Buzzer Module

  • Operating Voltage 3.5V ~ 5.5V
  • Storage Temperature -30°C ~ 105°C [-22°F ~ 221°F]
  • Dimensions 18.5mm x 15mm [0.728in x 0.591in]
  • Maximum Current 30mA / 5VDC
  • Resonance Frequency 2500Hz ± 300Hz
  • Minimum Sound Output 85Db @ 10cm
  • Working Temperature -20°C ~ 70°C [-4°F ~ 158°F]
P-012: Active Piezo-Buzzer module
Active Buzzer Module KY-012 Arduino module, it produces a single-tone sound when signal is high. To produce different tones use the KY-006 Passive Buzzer module.


KY-012 Specifications

The KY-012 Active Buzzer module consists of an active piezoelectric buzzer, it generates a sound of aproximately 2.5kHz when signal is high.



View Complete Details

Hall Magneticfield-Sensor Module

  • Operating Voltage 4.5V to 24V
  • Operating Temperature Range -40°C to 85°C [-x°F to x°F]
  • Dimensions 18.5mm x 15mm [0.728in x 0.591in]
P-003: Hall Magneticfield-Sensor module
PE-003 Arduino Hall Magnetic Sensor Module is a switch that will turn on/off in the presence of a magnetic field.


Specification

The PE-003 Hall Magnetic Sensor consists of a 3144EUA-S sensitive Hall-effect switch for high-temperature operation, a 680 resistor and a LED.Compatible with popular electronics platforms like ArduinoandRaspberry Pi.



View Complete Details

Switched Upper & Lower Light Tubes

  • KVB-30D 38 pounds
  • 20.1 x 16.1 x 5.9 inches KVB-30D
  • full size black
Exposure Unit KVB-30D
Independently switched upper & lower light tubes for exposure of single/double sided PCB's Built-in vacuum pump allowing the user to freeze the PCB's in place for perfect alignment to artwork An adjustable timer & counter for setting exposure time. - 110V/200Woperation A convenient "re-expose" button for repeat settings when doing multiple PCB's. 6 each 15 watt UV lamps (3 upper/3 lower) - Exposure area: 16" x 9.5"


Manufacturer : Kinsten Electronics



The Kinsten UV Exposure Box has a maximum exposure area 230 x 380mm and can be used for single sided, or double sided PCB's.


It includes digital timer & vacuum table.


Three (3) FL-15 tubes top and bottom, ensure high intensity ultra-violet radiation for rapid exposure time. For applications that require more intense UV, Kinsten now offer the KVB30DQ with four (4) lamps per side for 220V regions and KVB30DT with five (5) lamps per side for 110V regions. Due to the size of the ballasts, 240V regions do not yet have a high intensity model.


The dominant UV wavelength is 350400nm and the KVB-30D, while designed for use with Kinsten presensitised PCB, is often suitable for other applications that require transfering an image to a UV sensitive surface. They have been used in other applications including label making and rubber stamp production, although please check suitability first.




  • Independently switched upper & lower light tubes for exposure of single/double sided PCB's

  • Built-in vacuum pump allowing the user to freeze the PCB's in place for perfect alignment to artwork

  • An adjustable timer & counter for setting exposure time. - 110V/200Woperation

  • A convenient "re-expose" button for repeat settings when doing multiple PCB's.

  • 6 each 15 watt UV lamps (3 upper/3 lower) - Exposure area: 16" x 9.5"


View Complete Details

SMD Hot Air Rework Station

  • Weight 3700g
  • Model No. SS-989B
  • Power consumption 700 W
  • Soldering power 60 W
  • Soldering iron temperature range 200~480°C
  • Hot air temperature range indoor temperature~480°C
  • Hot air & soldering iron temperature Calibration Yes
  • Soldering iron heating element Alumina ceramic
  • Time to heat up to 300 °C 36 sec.
  • Air volume 24 L/min. (Max.)
  • Controller PCB Integrated to 1 pcs
  • Main power switch Yes (UL approve)
  • Independent power switch for soldering iron and hot air gun Yes (UL approve)
  • Additional ground contact Yes
  • Connecting wire UL AWM 105°C wire
  • Handpiece power wire AWG 20 (0.5 mm²)
  • Wire protection By UL heat-shrinkable tubing
  • Case SPCC 1.2mm
  • Power cord socket Yes (UL approve)
  • Power cord 18 AWG (0.8 mm²)
  • Certificate & RoHS CE & RoHS
  • Heating Element Metal Heating Core
  • Pump/Motor Type Diaphragm Pump
  • Air Capacity 24L/min (max)
  • Equipment noise 45dB
  • Temperature Display LED
  • Power Input 220V 50Hz
  • Dimensions 330(L)x275(W)x195(H)mm
  • Accessories Soldering Iron (60W)
  • 9SS-900-SI x 1pcs Hot Air Gun
  • 220V x1 pcs Soldering Stand
  • 1pcs Nozzle
  • 9SS-900-A1 (Ø2.2mm) x 1pcs 9SS-900-A2 (Ø6.6mm) x 1pcs 9SS-900-A3 (Ø8.5mm) x 1pcs Individual packing
SS-989B SMD Hot Air Rework Station
2 In 1 SMD Hot Air Rework Station AC220240V 700W


Manufacturer : Proskit




Description

2X Lifetime than traditional heater


Heat Fast , 36sec 300 oC By Alumina Ceramic heating element


Smart Microprocessor Accurate temperature controlled


Auto Cooling System Prolongs the service life





Features

2 In 1 rework station to save cost


Closed circuit sensor design


High power, quick warm up times


Individual function start saves energy


LED digital display


Quiet operation & ESD safe design


Auto cool-off process to prolong the life of heating element


Interchangeable and applicable to most of branded hot air nozzles and tips


Silicone Handpiece Cord Wire heat-resistant up to 200oC


AWG 20 (0.5mm2) UL Certified Wires


Soldering iron heater made by Alumina Ceramic




View Complete Details

Mini Soldering Station AC Switch

Features



Precision temperature control: 330C (626F)
Super slim, pen-like style for greater control and visibility
Specially designed for repairs to cell phones and PC boards
Conductive soldering stand
Dual voltage AC 110/220V


Voltage

Consumption Temperature Replacement 
heater

Standard Plug

Individual packing

220

4~14W ~330°C 
(~626°F)
9SS-201-H

B

Color box


View Complete Details

Gas Soldering Iron Kit-Auto Ignition

Features





  • Butane is easy to refill and check with see-through fuel window



  • Auto ignition is easy to start and operate under any condition



  • Adjustable flame control for precision use



  • 10 inone kit is convenience for multi-functional operating purpose



Contents:




  • Blow pen torch, protection cap, soldering head, needle soldering tip, 2.4mm soldering tip, double sharp tip, hot knife tip, hot air blower, polyfoam cutter, tube ofsolder, tip-cleaning sponge with safety standand tool rest packed in rugged plastic case.



Soldering Temperature

Hot Blow Temperature

Torch Temperature

Fuel Capacity

Time

Size

400°C

500°C

1300°C

26ml

100~120m

         
View Complete Details

Solder Paste

Features



Our soldering paste is composed of metal powder activated flux and blending agents. The area and thickness to be soldered can be easily controlled. No spot appears in non-soldered area. The paste has a good diffusion and non-corrosion.


View Complete Details

Desoldering Wick

  • Width(mm) 2.0
  • Length(m) 1.5
  • Individual Packing Inner Box
8PK-031B: Desoldering Wick
Desoldering Wick for Width 2.0mm


Manufacturer : Proskit

Manufacturer part number : 8
View Complete Details

Smoke Absorber

SS-593A: Smoke Absorber
Smoke Absorber (AC 110-120V 23W)


Manufacturer : Proskit



Features



1.Remove noxious fumes quickly, safely and efficiently
2.The fan is fully adjustable, quiet, and long service life.
3.Portable and desktop design, easy to place and move, low noise and long life service
4.The replaceable filter is made by urethane foam with refined, activated, high absorption carbon
5.Dimension (O.D.): 220*270*168mm



SS-593A

SS-593B

SS-593H

Power Supply

110-120V, 50 Hz

220-240V, 50Hz

220-240V, 50Hz

Power Cord

A type, 1.3M

B Type, 1.3M

H Type, 1.3M

Power Consumption

23W

Capacity

1m3/min(max)

Extra accessories

Filter x 2 Pieces, size:130*100*10mm (Part# 5SS-593-F) 

View Complete Details

Convertible Soldering Iron/Gun

  • Voltage 220~240V
  • Consumption 30(W)
  • Temperature 400°C±10%
  • Heater 5SI-S106B-H
  • Standard plug* B
  • Individual packing  Blister card
SI-S106B: Convertible Soldering Iron/Gun
Convertible Soldering Iron/Gun 220240V


Manufacturer : Proskit


Features



Replacement tip:Please follow up 8PK-S120N Series tips
Converts easily from pen to gun configuration.
When not in use handle covers tip for storage protection.



View Complete Details

Heat Gun With LCD Display AC

SS-621B : Heat Gun
Heat Gun with LCD Display AC 220V-240V 50Hz




Features



SS-621 LCD Heat Gun comes with LCD display provides powerful, accurate, controllable heat and
air-flow to get the job done well. It is a brand new product With 2 extra nozzles which can be used for a wide variety of applications, such as bending and forming plastics, drying body fillers, removing decals, spot drying paint, shrinking tubing, packaging and more.



  • Comes with Mabuchi motor which provideshigh performance and long service life.

  • Adjustable stepless temperature rangefrom 100C650C and2 position air volume adjustment.

  • Smart overheated protection design.

  • 20 second automatic cool air flow to prevent accidental burns and to extend life of heating element.

  • Electronic air flow and temperature control system maintains constant temperature, perfect for applications requiring consistent application of heat.



Model Name Voltage Watt Setting Temperature Air Volume Plug
SS-611B 240V 50Hz 2000W I 100~400°C 200L/min B type
II 100 ~650°C 500L/min
SS-611H 240V 50Hz 2000W I 100~400°C 200L/min H type
II 100 ~650°C 500L/min
View Complete Details

Heat Gun Set

SS-611B : Heat Gun Set
Heat Gun Set 240V/1500W


Features:



  • Smart overheat protection design

  • Automatic cool air flow to reduce waiting time from overheating shut down while working

  • 2 temperature settings from 300C500C for a variety of applications

  • Dual color ergonomic grip and lightweight design provides greater comfort

  • Includes 4 nozzles and 1 scraping tool with carrying case, easy to carry and store


Model No. Voltage Watt Air Volume Temperature Plug
SS-611B 230~240V 50Hz I-750W II-1500W I: 280L/min II: 480L/min I-300°C II-500°C
View Complete Details

Digital Ultrasonic Cleaner

  • Voltage AC 220-240V 50Hz
  • Power 50 W
  • ultrasonic frequency 46, 000Hz (46 KHz)
  • Tank Capacity 700ml (Max: 600ml)
  • Timer Setting 5 cleaning programs 180s→ 300s→ 480s→ 90s→ 600s-
  • Maerial of Tank Stainless steel SUS304
  • Material of Housing ABS
  • Gross Weight (G.W.) 1.4Kgs/3.08lb
  • Weight (N.W.) 1.0Kgs/2.2lb
  • Dimensions (LxWxH) 228 x 172 x 143mm (9.0"x 6.8"x 5.6")
  • Accessories Disk Holder / Watch Stand / Basket
SS-803F : Digital Ultrasonic Cleaner
Digital Ultrasonic Cleaner 700ml 220V


Features




  • Green cleaning No harmful chemicals

  • To make item cleaning more easily and safe only by using tap water

  • Use ultrasonic bubbles to break down dirt (46, 000Hz)

  • Digital operation with 5 cleaning programs

  • Use separately-excited circuit to generate steady oscillation

  • 15% better cleaning and 10% longer product life than self-excited type



View Complete Details

Heavy Duty Waterproof Case

TC-266 : Heavy Duty Waterproof Case
Heavy Duty Waterproof Case (O.D.:340x260x170mm)


Features





  • Made ofABS thick resin, durable and anti-shock



  • All round water-tight seal for optimum protection of equipment inside


  • Large rust proof latches with padlock eye for better security and safety.


  • comfortable grip handle for easy carrying of heavy loads



  • Ideal for carrying power tools, hand tools, precision equipments and instrumentsetc.




Model No.

Material

Load Capacity

I.D.(LxWxH)

O.D.(LxWxH)

Individual Packing

TC-265

ABS

15 KG

330x217x160mm

340x260x170mm

View Complete Details

Tility Component Storage Box

  • Material P.P.
  • Optional divider 503-132E-D12 (12pcs/bag)
203-132E : Utility Component Storage Box
Utility Component Storage Box (O.D.:200x135x39mm)
View Complete Details

Instrument Cases

203-115A : Instrument Cases
Instrument Cases (O.D.:200x158x64mm)


Features



The durable ABS plastic case allow for various PCB mounting positions. Adhesive feet and screws are included choose from 2 size. 203-115B has ventilation slots and speaker recess.

Unit: mm



View Complete Details

Fiber Optic Connector Cleaner

FB-C010 Fiber Optic Connector Cleaner
Refillable cleaning tape Full cleaning for SC , FC, MU, LC, ST, D4, DIN Connectors





Description



Refillable cleaning tape
Full cleaning for SC , FC, MU, LC, ST, D4, DIN Connectors





Features




  • Special non-alcohol high desity textile fiber type eliminates the need for solvents.

  • Offering over 500 cleans for SC, FC, MU, LC, ST, D4, DIN connectors.

  • Indication see through window for easy checking.

  • The refillable cleaning tape:Model No.FB-C010-RPM.




Model NO. Material Cleaning
times
Applications Dimensions
FB-C010 high density
textile fibers
500/per box For cleaning SC , FC ,
ST, MU, LC, D4, MT,
DIN connector
115×79×32mm




View Complete Details

Fiber Optic Basic Cleaning Kits

PK-9460 Fiber Optic Basic Cleaning Kits
Ideal for removing and trapping contaminants of fiber optic connector end face in fiber optic installations. ProsKit cleaning kit provides a complete selection of fiber optic cleaning products, includes cleaning liquid, wipers, cleaner , bulb blower, inspection scope and power meter

Features


1. FB-C010 Fiber Optic Connector Cleaner



  • Refillable cleaning tape

  • Full cleaning for SC , FC, MU, LC, ST, D4, DIN Connectors


2. FB-C008/FB-C009 Fiber Optic one Click Cleaner



  • One click for full cleaning

  • 800 cleans for FC/PC, ST, SC or LC MU connectors

  • 180 rotating cleaning system

  • Easy pushing motion

  • Extendable nozzle

  • Indication window


Model Product Name PK-9460
Basic Cleaning Kit

PK-9461
Basic Cleaning and Inspection Kit

PK-9462
Basic Cleaning, Inspection and Loss Test Kit

MS-153A Bulb Blower (Φ42mm)
FB-C008

2.5mm Fiber Optic one Click Cleaner

FB-C009 1.25mm Fiber Optic one Click Cleaner
FB-C010 Fiber Optic Cleaning Cassette
FB-C011 Lint free wiper
9C003 Cleaning Liquid
8PK-MA009 Fiber Optic Viewing Scope Kit  
MT-7601

Fiber Optic Power Meter




View Complete Details

Fiber Optic Basic Cleaning, Inspection And Test Kit

PK-9462 Fiber Optic Basic Cleaning, Inspection and Test Kit
Ideal for removing and trapping contaminants of fiber optic connector end face in fiber optic installations. ProsKit cleaning kit provides a complete selection of fiber optic cleaning products, includes cleaning liquid, wipers, cleaner , bulb blower, inspection scope and power meter



Features


1 .MT-7601 Fiber optic power Meter
Fiber optic power test for 850nm/ 1300nm/ 1310nm/ 1490nm/1550nm/1625nm Wavelengths


2. FB-C008/FB-C009Fiber Optic one Click Cleaner



  • One click for full cleaning

  • 800 cleans for FC/PC, ST, SC or LC MU connectors

  • 180 rotating cleaning system

  • Easy pushing motion

  • Extendable nozzle

  • Indication window


3. FB-C010Fiber Optic Connector Cleaner



  • Refillable cleaning tape

  • Full cleaning for SC , FC, MU, LC, ST, D4, DIN Connectors


4. 8PK-MA009 Fiber Optic Viewing Scope Kit



  • Makes it simple to view ST / SC / FC

  • 200X magnification


Model Product Name PK-9460
Basic Cleaning Kit

PK-9461
Basic Cleaning and Inspection Kit

PK-9462
Basic Cleaning, Inspection and Loss Test Kit

MS-153A Bulb Blower (Φ42mm)
FB-C008

2.5mm Fiber Optic one Click Cleaner

FB-C009 1.25mm Fiber Optic one Click Cleaner
FB-C010 Fiber Optic Cleaning Cassette
FB-C011 Lint free wiper
9C003 Cleaning Liquid
8PK-MA009 Fiber Optic Viewing Scope Kit  
MT-7601

Fiber Optic Power Meter




View Complete Details

Key Switch Module

  • Rating 50mA 12VC
  • Environment temperature -25°C to 105°C [ -13°F to 221°F]
  • Electrically Life 100, 000 cycles
  • Operating Force 180/230(±20gf)
  • Dimensions 18.5mm x 15mm [0.728in x 0.591in]
P-004: Button-module
Arduino Key Switch Module PE-004 is a push buttonthat will output a high signal when pressed.


Specifications

The module consists of a FZ1713 tactile push button switch and a resistor. Compatible with popular electronics platforms like Arduino, Raspberry Pi and Esp8266.



View Complete Details

RGB LED SMD Module

  • Operating Voltage 5V max Red 1.8V ~2.4V Green 2.8V ~ 3.6V Blue 2.8V ~ 3.6V
  • Forward Current 20mA ~ 30mA
  • Operating Temperature -25°C to 85°C [-13°F ~ 185°F]
  • Dimensions 18.5mm x 15mm [0.728in x 0.591in]
P-009: RGB LED SMD module
RGB full color LED Module KY-009 for Arduino, emits a range of colors by mixing red, green and blue. The amount of each primary color is adjusted using PWM.


KY-009 Specifications

The KY-009 RGB Full Color LED SMD Module consists of a 5050 SMD LED, use with limiting resistors to prevent burnout.Compatible with popular electronics platforms like Arduino, Raspberry Pi and ESP8266.



View Complete Details

Temperature-Sensor Module

  • Operating Voltage 5V
  • Temperature measurement range -55°C to 125°C [-67°F to 257°F]
  • Measurement Accuracy ±0.5°C
PE-013: Temperature-Sensor module
Analog Temperature Sensor module KY-013 for Arduino, measures ambient temperature based on resistance of the thermistor.


KY-013 Specifications

The KY-013 Analog Temperature Sensor module consist of a NTC thermistorand a10 k resistor. The resistance ofthe thermistorvaries with surrounding temperature, we'll use theSteinhartHart equation to derive precise temperature of the thermistor.



View Complete Details

Relays Module

  • TTL Control Signal 5VDC to 12VDC (some boards may work with 3.3)
  • Maximum AC 10A 250VAC
  • Maximum DC 10A 30VDC
  • Contact Type NC and NO
  • Dimensions 27mm x 34mm [1.063in x 1.338in]
P-019: 5V Relays module
Arduino KY-019 Relay Module is used to control AC circuits, the relay acts as a switch that responds to a signal received from the Arduino, it has an integrated LED that indicates if the signal is high or low. Commonly used in IoT projects to control lights and other electronic appliances.


Specifications

The KY-019 consist of a 1M resistor, a LED, a1N4007 rectifier diode and a 5VDC relay capable of handling up to 250VAC and 10A.


On the DC side of the board there are 3 pins for signal, power and ground. On the AC side there are 3 contacts, NC (Normally Closed), Common and NO (Normally Open).



View Complete Details

Tilt Switch Sensor Module

  • Operating Voltage 3.3V to 5v
  • Output Type Digital
P-020: Tilt switch module
KY-020 Arduino tilt switch sensor module. Closes the circuit when it is tilted to the side as long as it is moved with enough force and degree of inclination to activate the ball switch inside.


Specifications

The KY-020 consists of a 10k resistor and a metallic ball switch with bidirectional conduction that will open/close the circuit depending on its tilt degree. It does not measure tilt angle.



View Complete Details

Screwdriver Probe Voltage Tester

SD-328H Screwdriver Probe Voltage Tester
SD-328H Screwdriver Probe Voltage Tester
Screwdriver Probe Voltage Tester (AC 110250V)



Features


  • Easy and safe

  • Tests AC/DC voltage from 110-250V

  • Handy pocket screwdriver is a fully functional voltage tester

  • Insulated screwdriver shaft

  • Convenient screwdriver tip and pocket clip









  • Technical Specifications:

  • Power supply: Through the test sample

  • Range of measurement: 110-250V AC

  • Frequency: 50500Hz

  • Power consumption:
View Complete Details

Cordless Drill Driver

PT-1441F : Cordless Drill Driver
Cordless Drill Driver 14.4V (230V AC 50Hz)


Features





  • Comply with CE safety standards



  • No-Load speed 0-550rpm



  • 21+1 Adjustable torque settings for screwing, and drilling



  • Maximum output torque up to 7Nm



  • Removable battery pack for charging convenience



  • 3/8 (10mm) Keyless Chuck for driver bits or drills



  • Variable speed trigger for complete control



  • Switch for forward or reverse rotation. Easy to screw / unscrew.




Main body Model No. PT-1441A PT-1441F
Max. Drilling capacity Steel: Ø6mm Concrete: ø8mm Wood:Ø10mm
Torque setting 21+1 positions
Rated no load speed One Gear Speed: 0-550rpm
Output torque 7 Nm (71.4 kgf-cm/62.0 lbf-in)
Drive (Collet) 3/8" (10mm) Keyless Chuck
Special function Switch for forward or reverse rotation,
with drill function
Overall length 225mm x 245mm
  Model No. 5PT-1441-BAT
Battery Battery type Ni-Cd
Battery voltage 14.4V
Battery capacity 1000mAh
Charging time 3-5 hours
Free running time 40min
Adapter Model No. 5PT-1441-ADA 5PT-1441F-ADF
Input voltage 120V AC 60Hz 230V AC 50Hz
Output voltage DC 18V 400mA DC 18V 400mA
     
Charger Model No. 5PT-1441-CH
Voltage DC 18V 400mA
Standard
Accessories
Bits set 6pcs drill: Ø 1.5, 2.5, 3, 4, 5, 6mm
6pcs 25mm Driver Bits:
5.0, 6.0 #1, #2 PZ#1, PZ#2
1 pcs Magnetic insert bits holder
1 pcs 45mm double ends driver bits
#2, 6.0
Others Adapter and Charger / Blow-molded case
(380x280x95mm)
Optional bits set 5PT-1080-P1(13 pcs/set)
Individual packing Color sleeve shrink








View Complete Details

Cordless Pocket Screwdriver

PT-0721F : Cordless Pocket Screwdriver
Cordless Pocket Screwdriver 7.2V (230V AC 50Hz)


Features





  • Two Gear Speed : 0-200RPM/0-400RPM



  • 1300mAh Li-ionBattery. Long life battery pack, anti-pollution



  • 16 Adjustable torque settings



  • Maximum output torque up to 5Nm



  • Quick Release Chuck



  • Switch for forward or reverse rotation.



  • BatteryPower Indication



  • LED light provides convenient work in dark



  • Over Charging and Discharging Protection



  • Equipped with 7.2V 1300mAh rechargeable Li-ion battery



  • Charging time: 3-5hrs,



  • Free running time: 70min. (unload speed)




Model No. PT-0721A PT-0721F
Main
body
Torque setting 15+1 Position
Rated no load
speed
two gear speed:0-200rpm/0-400rpm
Output torque 5Nm (51 kgf-cm / 44.26 lbf-in)
Drive (collet) 1/4 qucik realess chuck
Special function Switch for forward or reverse rotation, quick
release chuck, LED light, battery power indicator
Overall length:
angled
160mm x 180mm
Battery Battery type Li-ion
Battery voltage 7.2V
Battery capacity 1300mAh
Charging time 3-5 hours
Free running time >70 min
Adapter Model No. 5PT-0721-ADA 5PT-0721-ADF
Input voltage 120V AC 60Hz 230V AC 50Hz
Output voltage DC 9V 300 mA DC 9V 300 mA
Adaptor plug F
Standard
accessories
Model No. 5PT-1361-P1
Bits set 4pcs 50mm Driver Bits: 5.0, 6.0 #1, #2
Other Adapter
Individal packing Double blister card





View Complete Details

Driver Socket Tool Set

SK-612401M : Driver Socket Tool Set
124Pcs 1/2".1/4" Driver Socket Tool Set


Features



The SK-612401M 124pcs 1/2"-1/4'' Dr. Socket Tool Set comes in an Aluminum Frame 3 Drawers Tool Case for easy tool organization. It contains complete range of high visibility sockets in 1/4"-1/2" drives-deep and standard depths, quick release 72 teeth reverse flat ratchet handle plus flex head gear wrench, long arm hex key set , screwdrivers, high leverage pliers, multimeter, locking pliers and most of popular tools to capability round out this versatile set

























































































































Top Layer : 0TR-612401MEVA-1



23pcs 1/2 Hand Socket 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 1,
9, 20, 21, 22, 23, 24, 25, 27, 28, 29, 30, 32mm



8pcs 1/2 Hand Deep Socket 10, 11, 12, 13, 14, 17, 19, 22mm



1/2 Extension Bar W/Quick Release 125mm



1/2 Extension Bar W/Quick Release 250mm



1/2 Sliding T Handle W/Quick Release 250mm



1/2 LED Light Adaptor



1/2 Universal Joint



1/2 72 Teeth Reverse Flat Ratchet Handle W/Quick Release



Drawer 1 : 0TR-612401MEVA-2



14pcs 1/4 Hand Socket 1/4, 4, 4.5, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 13, 14mm



13pcs 1/4 Hand Deep Socket 4, 4.5, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 13, 14mm



18pcs 1/4 Hand Bits Socket T10, T15, T20, T25, T30, T40, H3, H6,
H4, H5, H8, PH1, PH2, PZ1, PZ2, SL4, SL5.5, SL6.5



2pcs 1/2 Spark Plug Socket W/Magnetic 16, 21mm



1/4 Extension Bar W/Wobble 2 Way 52mm



1/4 Extension Bar W/Wobble 2 Way 100mm



1/4 Extension Bar W/Quick Release 150mm



1/4 Sliding T Handle 115mm



1/4 Universal Joint



1/4 Spinner Handle



1/4 72 Teeth Reverse Flat Ratchet Handle W/Quick Release



1/4'' x 145mm F type handle



Multi-Purpose Box(O.D99x66x36mm)



Drawer 2 : 0TR-612401MEVA-3



9pcs Ball-Point Long Arm Hex Key 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10mm



7pcs Flex Head Gear Wrench 8, 10, 11, 13, 14, 17, 19



Drawer 3 : 0TR-612401MEVA-4



2pcs Go-Through Screwdriver SL8x150mm, PH3x150mm



6pcs Pro-Soft Screwdriver SL6x100mm, SL6x40mm,
SL6x200mm, PH2x100mm, PH2x40mm, PH2x250mm



Telescopic Magnetic Pick Up Tool



Cover



3 1/2 Compact Digital Multimeter



8.5 High Leverage Combination Cutting Plier



8 High Leverage Diagonal Cutting Plier



8 High Leverage Long Nose Plier



2pcs Adjustable Locking Plier 7, 9(Long Nose)



Aluminum Frame 3 Drawers Tool Case 485x260x333mm



Individual PackingColor Box




View Complete Details

Fiber Tester ST Type

  • Type Individual packing
  • SC Blister card
3PK-NT018N-ST : Fiber Tester
Fiber Tester ST Type

Features:
Fastest display
Easiest operation
The most cost-effective solution
Automatically power-saving mode
Power on & battery low indicator


Specifications:
Peak wavelength: 1300nm
Fiber core: 62.5/125
Power: 9-volt battery


DBm to micro Watt conversion:
-20dBm=10 micro Watt -30dBm=1.00 micro Watt
-21dBm=7.9 micro Watt -31dBm=0.79 micro Watt
-22dBm=6.3 micro Watt -32dBm=0.63 micro Watt
-23dBm=5.0 micro Watt -33dBm=0.50 micro Watt
-24dBm=4.0 micro Watt -34dBm=0.40 micro Watt
-25dBm=3.2 micro Watt -35dBm=0.32 micro Watt
-26dBm=2.5 micro Watt -36dBm=0.25 micro Watt
-27dBm=2.0 micro Watt -37dBm=0.20 micro Watt
-28dBm=1.6 micro Watt -38dBm=0.16 micro Watt
-29dBm=1.3 micro Watt -40dBm=0.10 micro Watt
View Complete Details

Fiber Tester SC Type

  • Type Individual packing
  • SC Blister card
3PK-NT018N-SC : Fiber Tester
Fiber Tester SC Type


Features:
Fastest display
Easiest operation
The most cost-effective solution
Automatically power-saving mode
Power on & battery low indicator


Specifications:
Peak wavelength: 1300nm
Fiber core: 62.5/125
Power: 9-volt battery


DBm to micro Watt conversion:
-20dBm=10 micro Watt -30dBm=1.00 micro Watt
-21dBm=7.9 micro Watt -31dBm=0.79 micro Watt
-22dBm=6.3 micro Watt -32dBm=0.63 micro Watt
-23dBm=5.0 micro Watt -33dBm=0.50 micro Watt
-24dBm=4.0 micro Watt -34dBm=0.40 micro Watt
-25dBm=3.2 micro Watt -35dBm=0.32 micro Watt
-26dBm=2.5 micro Watt -36dBm=0.25 micro Watt
-27dBm=2.0 micro Watt -37dBm=0.20 micro Watt
-28dBm=1.6 micro Watt -38dBm=0.16 micro Watt
-29dBm=1.3 micro Watt -40dBm=0.10 micro Watt


View Complete Details

Mercury Tilt Switch Module

  • Operating Voltage 3.3V to 5.5V
P-017: Tilt switch module (type 1)
Arduino KY-017 mercury tilt switch module, it uses a small mercury ball that completes the circuit when you tilt the module


Specifications

This moduleconsists of a mercury switch, a 680 resistor and a LED that will light up when tilt is detected. The mercury ball will open/close the circuit when the module is rotated.



View Complete Details

Tone And Probe Kit

Description


For professionals who need fundamental wire identification tools without the extra cost, the 3PK-NT023N basic Tone and Probe Kit is the answer. Use it on de-energized AC wire, telephone/twisted pair wire, all voice and data category rated cable, speaker wire, virtually any cable or wire!



  • Fast, accurate wire identification

  • Rugged industrial design

  • Sends tone to identify wires

  • Three selectable tone outputs

  • Two-line polarity indication

  • Continuity test

  • Adjustable volume control

  • Visual signal strength indication

  • Powerful speaker for noisy environments

  • Recessed telephone test set connectors

View Complete Details

Laser Sensor Module

  • Wavelength 650 nm
  • Color Red
  • Supply Voltage 5 Vdc
  • Current 30 mA
P-008: Laser sensor module
This Keyes device is one of the more common devices found in Arduino sensor kits. Coupled with other components, it can be used to create trip wires or optical effects. The KY-008 is particularly neat because it can be directly powered from an Arduino output pin as it only draws 30 mA from the processor that has outputs rated for 40 mA.
View Complete Details

Photo Resistor Module

  • Operating Voltage 3.3V to 5V
  • Output type Analog
P-018: Photoresistor module
Arduino KY-018 Photoresistor module, used to measure light intensity. It can determine the presence or absence of light.


Specifications

This moduleconsists of a photoresistor and a10kin-line resistor. The photoresistor's resistance will decrease in the presence of light and increase in the absence of it. The output is analog and determines the intensity of light.



View Complete Details

RGB 5mm LED Module

  • Operating Voltage 5V
  • LED drive mode Common cathode driver
  • LED diameter 5 mm
P-016: RGB 5mm LED module
KY-016 Arduino full color 5mm RGB LED, different colors can be obtained by mixing the three primary colors


Specifications

This module consists of a 5mm RGB LED and three150 limiting resistorsto prevent burnout. Adjusting the PWM signal on each color pin will result on different colors.



View Complete Details

Combi-Sensor Temperature Humidity

  • Operating Voltage 3.3V to 5.5V
  • Humidity measurement range 20% to 90% RH
  • Humidity measurement accuracy ±5% RH
  • Humidity measurement resolution 1% RH
  • Temperature measurement range 0ºC to 50ºC [32ºF to 122ºF]
  • Temperature measurement accuracy ±2ºC
  • Temperature measurement resolution 1ºC
  • Signal transmission range 20m
P-015: Combi-Sensor Temperature+Humidity
KY-015 Arduino temperature and humidity sensor module, provides a digital serial interface to measure humidity and temperature.


KY-015 Specifications

This module consist of a DHT11 digital humidity and temperature sensor and a 1 k resistor. The DHT11 uses an internal thermistor and a capacitive humidity sensor to determine environment conditions, an internal chip is responsible forconverting readings to a serial digital signal.



View Complete Details

Corded Clippers

  • Weight 620 g (without cable)
  • Power Euro - 230V
  • Drive professional V9000 oscillating armature motor, 6000 1 / min
  • Art. No 08147-016
  • EAN 4015110078142
  • Cable length 4 m
  • Blade set screwed, chrome blade with lever
  • Cutting width: 40 mm
  • Cutting length 0.5 - 2.9 mm
PRODUCT DETAILS
POWER:Powerful, robust net hair clipper for continuous use.
PROFESSIONAL:Durable and durable V9000 swing armature motor .
5 STAR WEDGE BLADE:Chrome-plated cutting set with a new geometry for a smooth cut and harmonious transitions.Faster cutting thanks to optimized hair absorption. Extended cutting area for increased cutting comfort.
INCLUDES:Includes 8 premium combs and powerful 4-meter cable.
View Complete Details

Professional Cordless Hair Trimmer

  • Drive DC motor, 6, 000 1 / min
  • Operating time of the battery 90 min, Li-ion
  • EAN 4015110011262
  • Weight 260 g
  • Cable length 2.3 m (plug-in transformer)
  • Charging time of the battery 180 min.
  • Mains voltage 230V
  • Blade set quick change system, Magic Blade
  • Cutting width 40 mm
  • Cutting length 0.7 -3 mm
  • Packing unit 6 pieces
Beretto NEW
High-performance motor Professional cordless hair trimmer



PRODUCT DETAILS


PROFESSIONAL:Highly efficient and durable lithium-ion battery without memory effect.90 minutes run time and 180 minutes load time.


DESIGN:Elegant design and attractive brushed chrome finish.


ERGONOMIC:Super compact, light and quiet.


COMPACT:Compact charging stand.


MAGIC BLADE:Precision stainless steel cutting set with quick-change system and integrated cutting length adjustment 0.7 - 3 mm.Can be combined with All In One Blade and Diamond Blade (optional).


Scope of supply:


4 attachment combs # 1 (3 mm), # 2 (6 mm), # 3 (9 mm), # 4 (12 mm), charging stand, teckertrafo, flat-top hairdressing comb, cleaning brush, oil, knife guard



View Complete Details

Vibration-switch Module

  • Operating Voltage 5v
  • Dimensions 18.5mm x 15mm [0.728in x 0.591in]
P-002: Vibration-switch module
Arduino Vibration Switch Module PE-002 Keyes allows detection of shock and vibration.


Specifications

The PE-002 Vibration Switch Module consists of a conductive vibration spring and a 10k resistor, it will react to shock and vibration by closing the circuit.



View Complete Details

Light Barrier-module

  • Operating Voltage 3.3 ~ 5V
  • Dimensions 18.5mm x 15mm [0.728in x 0.591in]
P-010: Light barrier-module
Photo Interrupter Module Keyes KY-010 for Arduino, will trigger a signal when light between the sensor's gap is blocked.




Specifications

THe KY-010 PhotoInterrupter module consists of an optical emitter/detector in the front and two resistors (1 k and 33) in the back. The sensor uses a beam of light between de emitter an detector to check if the path between both is being blocked by an opaque object.



View Complete Details

PCB Etching Tank Machine

Etching Tank ET-10
Kinsten etch tanks are suitable for etching single and double sided PCBs with most etchants. The thin, vertical standing, design uses minimal etchant. The tanks have graduations for easy measurement. The Kinsten ET10 tank can etch a maximum PCB size of 2025cm without heater, or 1725cm with heater. Use with 1000cc minimum, 1500cc maximum liquid. (1000cc = 1 litre)


Manufacturer : Kinsten Electronics


(1000cc = 1 litre)


Etch tanks include three clips to suspend the PCB in the liquid etchant, and a thermometer to monitor liquid temperature.


Options include an air pump to bubble agitate the etchant, and heater to maintain optimal etchant temperature, for more efficient etching.


The ET etch kits include etch tank, air pump, heater and thermometer.


View Complete Details

PCB Cutter KSC

PCB Cutter KSC-168A
The Kinsten PCB cutting tool is an easy and accurate method of cutting PCB's. While hacksawing and 'score and snap' can be used, Kinsten PCB shears allows a straight cut up to 300mm in a single operation and is the recommended method to cut both paper phenolic and fibreglass PCBs.


View Complete Details

Tank Contains Two Spray Wash Bars

PA103 Spray Wash
This tank contains two spray wash bars at the top, driven from a single mains water inlet, between which the developed, etched stripped or tinned board can be suspended to be rinsed. A bottom tube permits used water to be run off to waste. Width 180mm, Depth 525mm, Height 380mm.


Manufacturer : MEGA Electronics

This tank contains two spray wash bars at the top, driven from a single mains water inlet, between which the developed, etched stripped or tinned board can be suspended to be rinsed. A bottom tube permits used water to be run off to waste. Width 180mm, Depth 525mm, Height 380mm.
View Complete Details

Two Bench Top Shears

Two bench top shears suitable for cutting printed circuit board laminates, thin metal sheet and aluminium (1.5/2.0mm) or plastic labels / front panel materials. On lowering the operating handle, a spring loaded clamp is activated which holds the material securely during cutting, thus enabling cuts to be made with a mini-mum of effort. These shears are composed of an epoxy powder coated cast aluminium frame fitted with hardened and ground steel blades. The Model 45 has a clear acrylic front safety guard to protect the operator, whilst at the same time making it possible to see the blades so that the material to be cut can be aligned accurately. The Model 45 (illustrated) has an 18" cutting capacity
View Complete Details

ACTIVATED XENON TUBE FLASHLIGHT

ACTIVATED XENON TUBE FLASHLIGHT
Flash lights with effects for discos, . etc. You can adjust the flash frequency (fk138). Power 220 - 240 v.


Manufacturer : FUTURE KIT.


Flash lights with effects for discos, . etc. You can adjust the flash frequency (fk138). Power 220 - 240 v.

This kit is a kind of flashing kit that blinks when sound is detected and

does not blink when the sound disappears.

It can be applied for alarm or alarm.

- Power: 220VAC
View Complete Details

Mini Grinder Set

PT-5721F: Mini Grinder Set
Mini Grinder Set 7.2V (230V AC 50Hz)


Features




  • 1000mAh Li-ion Battery. Long life battery pack, anti-pollution.

  • Low vibration, high torque and lightweight ergonomically designed

  • Adjustable speed settings

  • Quick Release Chuck

  • Battery Power Indication

  • LED light provides convenient work in dark

  • Ideal for lightweight grinding, drilling, cutting, polishing, sanding, milling, sharpening, engraving and many other uses










Standard
accessories
Bitsset 2pcs brass collet (2.4x1, 3.2x1)
3pcs high speed drills (3/32" 2.4x 2, 1/8" 3.2 x1)
2pcs Engraving bits (2.4x 2)
2pcs diamond bits (3.2 x 2)
2pcs nylon brush (2.4, 3.2)
4pcs grinding stones (2.4x 2, 3.2 x2)
1pcs sanding band (2.4 x1)


 
Model No. PT-5721A PT-5721F
Main body Max. diameter Ø3.2
Rated no load speed 5000rpm~18000rpm
Battery Battery Type Li-ion
Battery voltage 7.2V
Battery capacity 1000mAh
Charging Time 3-5 hours
Free running time 60 min
Adapter
and
charger
Model No. 9PT-5721-CA 9PT-5721-CF
Input voltage 120V AC 60Hz 230V AC 50Hz
Output voltage DC 9V 300mA DC 9V 300mA
Adaptor plug A
  Model No. 9PT-5721-P2 (16pcs / set)


View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • Saif Alshamsi (Popular Electronic)
  • Store 1, M floor, Al Khabeesi Building, Salahudeen Road, Deira,Dubai, United Arab Emirates
  • Share us via