Post Your Requirement Menu

Welcome User

Other Products / Services

We are leaders in the market for providing best range of Explosion-proof Caution Spotlight Fittings, EMERGENCY EXIT LIGHT FITTINGS, Emergency Light Fittings, EXPLOSION-PROOF ANNULAR LIGHT FITTINGS and proof Fluorescent Lamp

Explosion-proof Caution Spotlight Fittings

Explosion protection to -CENELEC -IEC -NEC Can be used in Zone 1 and Zone 2 Zone 21 and Zone 22 Class 1, Zone 1 and Zone 2 Class 1, Division 1, Groups A, B, C, D Ultra-bright LED lamp, low power consumption and long service life. Lamp colour: red, blue, yellow, green. Enclosure in copper-free aluminium, powder coated surface, yellow (RAL1021).

View Complete Details

EMERGENCY EXIT LIGHT FITTINGS

Explosion protection to -CENELEC -lEC -NEC Can be used in Zone 1 and Zone 2 Zone 21 and Zone 22 Class I, Zone 1 and Zone 2 Class I, Division 1, Groups C, D Lighting both in normal condition and emergency condition; When the power supply is cut off, the light illuminates; provided with overcharge, over-discharge and short circuit protection. Designed with test button and sleep button. Press the test button and the lamp will enter emergency mode. The sleep button turns off the lamp, re-press the button and the lamp turns on and returns to operating status. Ultra-bright LED lamp, low power consumption and long service life up to 50, 000 hours; energy saving and environmentally friendly. Enclosure in copper-free aluminium, powder coated surface, yellow (RAL 1021). Toughened glass resistant to temperature changes.

View Complete Details

Emergency Light Fittings

Explosion protection to -CENELEC -IEC -NEC Can be used in Zone 1 and Zone 2 Class I, Zone 1 and Zone 2 Class I, Division 1, Groups C, D Enclosure in copper-free aluminium, powder coated surface, yellow (RAL1021). Lighting angle can be adjusted. Low-power halogen tungsten lamps with reflectors to increase lighting intensity. Emergency device with Ni-MH batteries which charge automatically; when the power supply is cut off the lights illuminate. Provided with overcharge and over-discharge protection. Toughened glass covers resistant to temperature changes.

View Complete Details

EXPLOSION-PROOF ANNULAR LIGHT FITTINGS

Explosion-proof Annular Light Fittings Explosion protection to -CENELEC -lEC -NEC Can be used in Zone 1 and Zone 2 Zone 21 and Zone 22 Class I, Zone 1 and Zone 2 Class I, Division 1, Groups C, D Power: 21W x1, 21W x 2. Enclosure in copper-free aluminium, powder coated surface: yellow (RAL1021) Powder coated wire guard: white. Toughened glass cover resistant to temperature changes.

View Complete Details

proof Fluorescent Lamp

Explosion protection to -CENELEC -lEC -NEC Can be used in Zone 1 and Zone 2 Zone 21 and Zone 22 Class I, Zone 1 and Zone 2 Class I, Division 2, Groups A, B, C, D Polycarbonate diffuser, high transmittance, resistance to heavy impact. Main enclosure is extruding formed of copper-free aluminium, anodic-oxidation treatment for surface. Both ends of enclosures are die-casting formed of copper-free aluminium, powder coated surface. Built-in electronic ballast, power factor ≥ 0.95. Special-made mounting bracket, the illumination angle can be adjusted on request. Emergency function is available on request. End of lamp life (EOL) rectification effect protection

View Complete Details

Incandescent Hand Lamps

Explosion protection to -CENELEC -IEC -NEC Can be used in Zone 1 and Zone 2 Class I, Zone 1 and Zone 2 Class l, Division 2, Groups A, B, C, D Incandescent lamp: Max. 60W Cable supplied on request Handle in plastic, with control push button Powder coated wire guard, white Toughened glass cover resistant to temperature changes Movable transformer available on request

View Complete Details

FLAMEPROOF ENERGY-SAVING LIGHTING

Explosion protection to -CENELEC -IEC -NEC Can be used in Zone 1 and Zone 2 Zone 21 and Zone 22 Class I, Zone 1 and Zone 2 Class I, Division 1, Groups A, B, C, D Two enclosure types separately for 42W and 68W compact energy-saving lamps, with good performance including rapid starting, flash free, high lighting efficiency, long service life and energy saving, etc. The luminous intensity of a 42W compact energy-saving lamp equals an 80W mercury lamp; the luminous intensity of a 68W compact energy-saving lamp equals an 125W mercury lamp. Powder coated wire guard; white. Toughened glass cover resistant to temperature changes,

View Complete Details

Led Street Lamps

Explosion protection to -CENELEC -IEC -NEC Can be used in Zone 2 Zone 21 and Zone 22 Class I, Zone 2 Class I, Division 2, Groups A, B, C, D Five enclosure types: 60, 90, 120, 150, 180 Applicable lamp and power (max.180W) LED: 60W, 90W, 120W, 150W, 180W Enclosure: Extrusion formed with good cooling performance. Unique design without an external power supply; power accessories and lamp are integrated.

View Complete Details

LED TANK INSPECTION VESSEL LIGHT FITTINGS

LED Tank Inspection Vessel Light Fittings Explosion protection to -CENELEC -IEC -NEC Can be used in Zone 1 and Zone 2 Zone 21 and Zone 22 Applicable lamp and power: LED lamps, energy-saving and long service life, 9W Enclosure in copper-free aluminium, powder coated surface, yellow (RAL1021)

View Complete Details

portable searchlight

Portable Searchlight Explosion protection to -CENELEC -IEC -NEC Can be used in Zone 1 and Zone 2 Zone 21 and Zone 22 Class I, Zone 1 and Zone 2 Class I, Division 1, Groups A, B, C, D Safe and reliable: the product has reliable explosion-proof performance, can safely and reliably work in various hazardous areas. The battery is equipped with a PTC thermistor and temperature fuse; double-protected circuit, safety performance enhanced. Efficient and energy-saving: equipped with a memory-free battery with long service life and low auto-discharge rate, it is economical and environmental friendly. Has an efficient solid state LED lamp, low energy consumption and long service life. Waterproof and damage-proof: the enclosure is made of an imported alloy with high strength and excellent strong impact resistant performance. The unique sealing type has very good water-proof performance Anti-strong interference: The scientific module driving circuit has strong anti-shock and anti-electromagnetic interference characteristics Heat resistant: LED radiator and battery are effectively isolated which improves the stability of the light Intelligent control: pulse dimming technology, strong light and working light modes can be changed at random. Has a battery detection indicator which can detect the working condition of the battery at any time. The intelligent charger is provided with a protection circuit Portable and flexible: small volume, light weight. Handling possibilities such as hand held and on shoulder satisfy different working requirements.  

View Complete Details

STRONG WORKING LIGHTS

Strong Working Lights Explosion protection to -CENELEC -IEC -NEC Can be used in Zone 1 and Zone 2 Class I, Zone 1 and Zone 2 Class I, Division 2, Groups A, B, C, D Safe and reliable: the product has good explosion-proof performance and can safely and reliably work in various hazardous areas. Efficient and energy-saving: special gas discharging lamp; high luminous efficiency, luminous flux is 5 times of that of a halogen lamp with the same power, illumination is 3 times that of a 100W halogen bulb, service life is 5-10 times of that of a normal halogen lamp, and for the same brightness the power consumption is 15% of that of a normal halogen lamp, good anti-shock effect, small heating value, safer and more reliable. Waterproof and damage-proof: the light is totally sealed and can work normally in wet environments, a special alloy enclosure ensures the light can resist strong shock and impact Economic and environmental friendly: the memory-free battery can be charged and laid aside for a year, the reserve of electricity is not less than 80% full after two years, it is not less than 50% low-voltage discharging protection circuit is set; reliably protects the battery and prolongs the service life Convenient and durable: a unique lamp cap, the lighting angle can be adjusted at random and there are wheels at the bottom to easily to move the lamp Other: normally a floodlight is provided; however a spotlight is available on request  

View Complete Details

Earth bonds & clamps

Earth bonds & clamps Where permanent connections are not appropriate, mechanical clamps offer the ideal solution. These are typically used on smaller scale installations where periodic disconnection for testing is required. All mechanical clamps are manufactured from high copper content alloy. They have high mechanical strength, excellent corrosion resistance and conductivity. Our range of earthing clamps are designed for connection of conductors to earth rods, reinforcing bars, steam pipes, handrails etc… Manufactured to offer corrosion resistance, conductivity and mechanical strength, these are essential considerations in an earthing design to ensure an earthing system remains operative for many years. All earth rod clamps have high strength copper alloy bodies and screws e.g. aluminium bronze, phosphor bronze etc., commercial brass is not used.  

View Complete Details

Air Rod Bases & Saddles

Air Rod Bases & Saddles The role of an air termination system is to capture the lightning discharge current and dissipate it harmlessly to earth via the down conductor and earth termination system. Therefore it is important to use a correctly designed air termination system. IEC/BS EN 62305-3 advocates the following, in any combination, for the design of the air termination: Air rods (or finials) whether they are free standing masts or linked with conductors to form a mesh on the roof Catenary (or suspended) conductors, whether they are supported by free standing masts or linked with conductors to form a mesh on the roof Meshed conductor network that may lie in direct contact with the roof or be suspended above it (in the event that it is of paramount importance that the roof is not exposed to a direct lightning discharge) The standard makes it quite clear that all types of air termination systems that are used shall meet the positioning requirements laid down in the body of the standard. It highlights that the air termination components should be installed on corners, exposed points and edges of the structure. The three basic methods recommended for determining the position of the air termination systems are: The rolling sphere method The protective angle method The mesh method

View Complete Details

Air Rod Brackets

Air Rod Brackets The role of an air termination system is to capture the lightning discharge current and dissipate it harmlessly to earth via the down conductor and earth termination system. Therefore it is important to use a correctly designed air termination system. IEC/BS EN 62305-3 advocates the following, in any combination, for the design of the air termination: Air rods (or finials) whether they are free standing masts or linked with conductors to form a mesh on the roof Catenary (or suspended) conductors, whether they are supported by free standing masts or linked with conductors to form a mesh on the roof Meshed conductor network that may lie in direct contact with the roof or be suspended above it (in the event that it is of paramount importance that the roof is not exposed to a direct lightning discharge) The standard makes it quite clear that all types of air termination systems that are used shall meet the positioning requirements laid down in the body of the standard. It highlights that the air termination components should be installed on corners, exposed points and edges of the structure. The three basic methods recommended for determining the position of the air termination systems are: The rolling sphere method The protective angle method The mesh method

View Complete Details

AIR RODS

The role of an air termination system is to capture the lightning discharge current and dissipate it harmlessly to earth via the down conductor and earth termination system. Therefore it is important to use a correctly designed air termination system. IEC/BS EN 62305-3 advocates the following, in any combination, for the design of the air termination: Air rods (or finials) whether they are free standing masts or linked with conductors to form a mesh on the roof Catenary (or suspended) conductors, whether they are supported by free standing masts or linked with conductors to form a mesh on the roof Meshed conductor network that may lie in direct contact with the roof or be suspended above it (in the event that it is of paramount importance that the roof is not exposed to a direct lightning discharge) The standard makes it quite clear that all types of air termination systems that are used shall meet the positioning requirements laid down in the body of the standard. It highlights that the air termination components should be installed on corners, exposed points and edges of the structure. The three basic methods recommended for determining the position of the air termination systems are: The rolling sphere method The protective angle method The mesh method

View Complete Details

air termination system

The role of an air termination system is to capture the lightning discharge current and dissipate it harmlessly to earth via the down conductor and earth termination system. Therefore it is important to use a correctly designed air termination system. IEC/BS EN 62305-3 advocates the following, in any combination, for the design of the air termination: Air rods (or finials) whether they are free standing masts or linked with conductors to form a mesh on the roof Catenary (or suspended) conductors, whether they are supported by free standing masts or linked with conductors to form a mesh on the roof Meshed conductor network that may lie in direct contact with the roof or be suspended above it (in the event that it is of paramount importance that the roof is not exposed to a direct lightning discharge) The standard makes it quite clear that all types of air termination systems that are used shall meet the positioning requirements laid down in the body of the standard. It highlights that the air termination components should be installed on corners, exposed points and edges of the structure. The three basic methods recommended for determining the position of the air termination systems are: The rolling sphere method The protective angle method The mesh method

View Complete Details

ANTI-VANDAL CONDUCTOR GUARD

By far the largest and most important component of any structural lightning protection or earthing system is the actual conductor. Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer. A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements. Specification will depend on whether the application is for an above ground structural lightning protection system, or a below ground earthing installation.Conductors for structural lightning protection systems Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties. The following sizes are suitable for the majority of above ground lightning protection systems: Flat tape conductor 25 x 3 mm bare tape, or 25 x 3mm PVC covered tape Solid circular conductor 8 mm diameter bare or PVC covered solid circular conductor Stranded conductor 70 mm² bare or PVC covered stranded conductor

View Complete Details

bare conductor

By far the largest and most important component of any structural lightning protection or earthing system is the actual conductor. Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer. A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements. Specification will depend on whether the application is for an above ground structural lightning protection system, or a below ground earthing installation.Conductors for structural lightning protection systems Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties. The following sizes are suitable for the majority of above ground lightning protection systems: Flat tape conductor 25 x 3 mm bare tape, or 25 x 3mm PVC covered tape Solid circular conductor 8 mm diameter bare or PVC covered solid circular conductor Stranded conductor 70 mm² bare or PVC covered stranded conductor

View Complete Details

BIMETALLIC CABLE CONDUCTOR

Bimetallic Cable  Conductor By far the largest and most important component of any structural lightning protection or earthing system is the actual conductor. Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer. A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements. Specification will depend on whether the application is for an above ground structural lightning protection system, or a below ground earthing installation.Conductors for structural lightning protection systems Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties. The following sizes are suitable for the majority of above ground lightning protection systems: Flat tape conductor 25 x 3 mm bare tape, or 25 x 3mm PVC covered tape Solid circular conductor 8 mm diameter bare or PVC covered solid circular conductor Stranded conductor 70 mm² bare or PVC covered stranded conductor

View Complete Details

flexible braid

By far the largest and most important component of any structural lightning protection or earthing system is the actual conductor. Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer. A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements. Specification will depend on whether the application is for an above ground structural lightning protection system, or a below ground earthing installation.Conductors for structural lightning protection systems Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties. The following sizes are suitable for the majority of above ground lightning protection systems: Flat tape conductor 25 x 3 mm bare tape, or 25 x 3mm PVC covered tape Solid circular conductor 8 mm diameter bare or PVC covered solid circular conductor Stranded conductor 70 mm² bare or PVC covered stranded conductor

View Complete Details

HARD DRAWN BAR

Hard Drawn Bar By far the largest and most important component of any structural lightning protection or earthing system is the actual conductor. Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer. A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements. Specification will depend on whether the application is for an above ground structural lightning protection system, or a below ground earthing installation.Conductors for structural lightning protection systems Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties. The following sizes are suitable for the majority of above ground lightning protection systems: Flat tape conductor 25 x 3 mm bare tape, or 25 x 3mm PVC covered tape Solid circular conductor 8 mm diameter bare or PVC covered solid circular conductor Stranded conductor 70 mm² bare or PVC covered stranded conductor

View Complete Details

LEAD COVERED CONDUCTOR

Lead Covered Conductor By far the largest and most important component of any structural lightning protection or earthing system is the actual conductor. Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer. A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements. Specification will depend on whether the application is for an above ground structural lightning protection system, or a below ground earthing installation.Conductors for structural lightning protection systems Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties. The following sizes are suitable for the majority of above ground lightning protection systems: Flat tape conductor 25 x 3 mm bare tape, or 25 x 3mm PVC covered tape Solid circular conductor 8 mm diameter bare or PVC covered solid circular conductor Stranded conductor 70 mm² bare or PVC covered stranded conductor

View Complete Details

PVC COVERED CONDUCTOR

PVC Covered Conductor By far the largest and most important component of any structural lightning protection or earthing system is the actual conductor. Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer. A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements. Specification will depend on whether the application is for an above ground structural lightning protection system, or a below ground earthing installation.Conductors for structural lightning protection systems Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties. The following sizes are suitable for the majority of above ground lightning protection systems: Flat tape conductor 25 x 3 mm bare tape, or 25 x 3mm PVC covered tape Solid circular conductor 8 mm diameter bare or PVC covered solid circular conductor Stranded conductor 70 mm² bare or PVC covered stranded conductor

View Complete Details

ROD TO CONDUCTOR COUPLING

The role of an air termination system is to capture the lightning discharge current and dissipate it harmlessly to earth via the down conductor and earth termination system. Therefore it is important to use a correctly designed air termination system. IEC/BS EN 62305-3 advocates the following, in any combination, for the design of the air termination: Air rods (or finials) whether they are free standing masts or linked with conductors to form a mesh on the roof Catenary (or suspended) conductors, whether they are supported by free standing masts or linked with conductors to form a mesh on the roof Meshed conductor network that may lie in direct contact with the roof or be suspended above it (in the event that it is of paramount importance that the roof is not exposed to a direct lightning discharge) The standard makes it quite clear that all types of air termination systems that are used shall meet the positioning requirements laid down in the body of the standard. It highlights that the air termination components should be installed on corners, exposed points and edges of the structure. The three basic methods recommended for determining the position of the air termination systems are: The rolling sphere method The protective angle method The mesh method

View Complete Details

Strike Pad

The role of an air termination system is to capture the lightning discharge current and dissipate it harmlessly to earth via the down conductor and earth termination system. Therefore it is important to use a correctly designed air termination system. IEC/BS EN 62305-3 advocates the following, in any combination, for the design of the air termination: Air rods (or finials) whether they are free standing masts or linked with conductors to form a mesh on the roof Catenary (or suspended) conductors, whether they are supported by free standing masts or linked with conductors to form a mesh on the roof Meshed conductor network that may lie in direct contact with the roof or be suspended above it (in the event that it is of paramount importance that the roof is not exposed to a direct lightning discharge) The standard makes it quite clear that all types of air termination systems that are used shall meet the positioning requirements laid down in the body of the standard. It highlights that the air termination components should be installed on corners, exposed points and edges of the structure. The three basic methods recommended for determining the position of the air termination systems are: The rolling sphere method The protective angle method The mesh method

View Complete Details

TINNED CONDUCTOR

Tinned Conductor By far the largest and most important component of any structural lightning protection or earthing system is the actual conductor. Selection of the correct conductor type for the installation is highly important, and is likely to be the initial consideration of a lightning protection or earthing system designer. A comprehensive range of copper and aluminium conductors is available in each of the main world standard formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes, to meet differing lightning protection and earthing requirements. Specification will depend on whether the application is for an above ground structural lightning protection system, or a below ground earthing installation.Conductors for structural lightning protection systems Lightning protection conductors are available in copper and aluminium, and are supplied bare or with PVC coating (see below). For most installations, copper is specified due to its high conductivity and anti-corrosive properties. The following sizes are suitable for the majority of above ground lightning protection systems: Flat tape conductor 25 x 3 mm bare tape, or 25 x 3mm PVC covered tape Solid circular conductor 8 mm diameter bare or PVC covered solid circular conductor Stranded conductor 70 mm² bare or PVC covered stranded conductor

View Complete Details

access fittings

The National Electrical Code defines a conduit body as “A separate portion of a conduit or tubing system that provides access through a removable cover(s) to the interior of the system at a junction of two or more sections of the system or at a terminal point of the system. Available with Self Tapping Screws / Brass Screws & Inserts Type C Type LB Type LL Type LR Type E Type T Type TB

View Complete Details

Adapters

Adapters Reduce conduit hubs to a smaller size or to connect two different sizes of conduit together Terminal Adapters Female Adapters (NPT Tapered Thread)

View Complete Details

PVC LSF Building Wires and Cables

PVC LSF Building Wires and Cables Aswathy can provide the full range of house wiring cables from 1.5 mm² to 1000 mm² with wide range of core colours. The conductor is plain annealed solid or stranded Copper conductors insulated with PVC or Heat Resistant PVC as per BS EN 50535-3-41. Oman Cables also manufactures twin flat wires up to 6mm² with or without Earth continuity conductor. The complete range of Wiring cables can be manufactured using Low Smoke Zero Halogen thermosetting insulation compounds conforming to BS EN 50535-2-31 or with compounds to suit customer’s specific requirements.

View Complete Details

CABLE CLEATS AND TIES

Cable Cleats and Ties   Aswathy’s  range of short circuit approved cable cleats which are extremely compact and simple to install. Comprehensively tested and 3rd party approved. We also offer Cable Ties in Stainless Steel, un-coated and coated.

View Complete Details

Cable Ladder System

Cable Ladder System is designed to offer high loading capacities together with significant weight reductions. Cable Ladders are designed to be safe, and give distinct benefits. For light loads such as instrumentation, data & telecom cables Corrosion resistant fibre reinforced plastic ladders Smart Cable Ladders for Ships Cable ladder for infrastructure Projects   Features: Solid side rail protection and system strength with smooth radius fittings. Maximum strength for long span applications Standard widths of 6, 12, 18, 24, 30 & 36 inches Standard depths of 3, 4, 5 & 6 inches Standard lengths of 10, 12, 20 & 24 feet Rung spacing of 6, 9, 12 & 18 inches

View Complete Details

Cable Tray

Cable Trays are made of either Steel, Aluminum, Fiber Reinforced Plastic (FRP) and we provide the following six different types and are available in Standard Width, Depth and Length Ladder Type Cable Tray Solid Bottom Cable Tray Trough Cable Tray Channel Cable Tray Wire Mesh Cable Tray Single Rail Cable Tray

View Complete Details

Cantilever Arm

Cantilever Arm We supply a range of simple to install cantilever support arms which can be used for supporting Cable Ladders and Cable Trays. They can also be fixed directly to wall.   Offshore Cantilever Arm Onshore Cantilever Arm Channel Bracket Cantilever Arm for Channel support Single Cantilever Double Cantilever

View Complete Details

Fire Resistant Cables

Fire Resistant Cables 600/1000V grade , plan annealed copper conductor, glass mica tapped, XLPE insulated, multi-core cables laid up and inner sheathed with LSF (or LSOH/LSZH), round galvanized steel wire armoured and outer jacket with LSF (or LSOH/LSZH). Specifications: BS7846 (Category F2) and BS 6387 (Category, C, W & Z). These Cables are meant for maintaining circuit integrity under fire condition for 3 hours (tested for 3 hours at 950o C temperature). Range:  From 2C x 1.5mm² to 4C x 400mm² From 5C x 1.5mm² to 5C x 70 mm²  

View Complete Details

HVAC clamp range

HVAC Support We offer a complete HVAC clamp range including solutions for both insulated and un-insulated ducting of both circular and rectangular types. The clamps are designed to minimize the fitting space required.

View Complete Details

Lighting Poles

Available in Steel, Aluminum, Fiberglass, RCC… Anchor / Burial /  Hinged Base Round / Square / Straight / Tapered Shaft Octagonal, Stepped or Round type Street / Flood – Straight and Hinged Towers, Compound, High Masts, Street, Stadium, Plant and Special Design Special Design Poles. Flag Posts Flood Light Towers

View Complete Details

Low Voltage Cables

XLPE Insulated Power Cables 600/1000 V grade, plain annealed Copper conductor. XLPE insulated, multi-core cables laid up and inner sheathed with PVC, round galvanized steel wire armored for multi cores and aluminium wire armored for single cores and outer jacket with PVC. Range: From 1C x 10 mm²to 1C x 1000 mm² From 2C x 1.5 mm² to 4C x 400 mm² Specification:  BS-5467, IEC 60502, part-1;S-6724 as per Iraq specs or any other international standards,  as well as customer specification. We also manufacture the cables for special applications which require enhanced fire performances as per IEC-60332-3, Low Smoke Zero Halogen characteristics as per BS6724, lead sheathed cables, anti-termite treatment, UV resistant & Water blocking feature, tinned copper wires in the armor for higher armor conductivity etc. PVC Insulated Power Cables 600/1000V Grade Plain annealed Copper conductor, PVC insulated, multi-core cables laid up and inner-sheathed with PVC, round galvanized steel wire armored for multi-cores and aluminium wire armored for single core and outer jacket with PVC. Range: From 1C x 10 mm² to 1C x 1000 mm² From 2C x 1.5 mm² to 4C x 400 mm² Specifications:  IEC-60502 Part-1, as per Iraq specs or any other international standards as well as customer specifications. We also manufacture the cables for special applications which require enhance fire performance as per IEC-60332-1 & IEC-60332-3, lead sheathed cables, anti-termite treatment, UV resistant, water blocking feature, tinned copper wires in the armor for higher armor conductivity etc.

View Complete Details

Tubing Clamps

Tubing Clamps   Tubing clamps are quick and easy to install and can be stacked and staggered to maximize the fitting space available. The protected clamps are independently vibration tested and approved.

View Complete Details

Weatherproof Flexible Cable Conduits

Weatherproof Flexible Cable Conduits Corrosion-proof, water-proof, anti-aging, good flexibility, firm structure, reliable performance, etc The thread can be specially made upon request (NPT, metric thread etc) The connector is made of high quality carbon steel. If requested, the whole conduit can be made of stainless steel. The length of flexible conduit can be specially made upon request.

View Complete Details

Overhead Line Conductors

Overhead Line Conductors Aswathy has capability to provide complete range of overhead line conductors in Aluminium, Aluminium Alloy and Copper. The standard range includes sizes up to 1000mm² as per BS, IEC, DIN, ASTM,  or any other international standard and customer’s specifications for all voltage applications. We can also provide conductors with XLPE or PVC covering. The standard types of conductors in our present manufacturing range are as follows: AAC All Aluminium Conductors AAAC All Aluminium Alloy Conductor ACSR Aluminium Conductor Steel Reinforced HDBC Hard Drawn Bare Copper conductor SDBC Soft Drawn Bare copper Conductor AAC + XLPE All Aluminium Conductor with XLPE insulation AAC + PVC All Aluminium conductors with PVE insulation

View Complete Details

Perforated Profiles

Perforated Profiles We offer a range of standard perforated profiles suitable for welding during construction. These can then be treated and coated together with the main structure..

View Complete Details

Pipe Clamps and Shoes

Our Pipe Clamps and Shoes are designed to be fully compatible with our channels, either by bolting directly in the pre-drilled holes or by using an adapter. The design also ensures they are easy to install without having to weld, and therefore maintain a high degree of flexibility.

View Complete Details

RACKS, INSTRUMENT STANDS AND EQUIPMENT PLATES

Racks, Instrument Stands and Equipment Plates Aswathy’s  range of equipment rack designs provide optimal area utilization and are easy and quick to install. We also has a range of different solutions for instrument stands and our versatile equipment plates are designed to fit a range of different equipment from multiple suppliers. Custom made versions are also available.

View Complete Details

light weight and cost saving support system

Support System Flexible, light weight and cost saving support system for all main disciplines including electrical, instrumentation, telecom, HVAC and piping. sections are available in a range of profiles, grades and materials to suit any application, however all share the same high quality engineering solutions. When compared to traditional welded supports, our systems are significantly lighter, quicker to install, safer in construction and more cost effective. Systems offer full flexibility in design and installation both in initial construction and in all subsequent adaptation or upgrade works.

View Complete Details

Weatherproof Cable Glands

Weatherproof Cable Glands Material of product: engineering plastic, stainless steel or nickel plated brass; Silicon rubber sealing ring, anti-aging, thermo-stability, high degree of protection Temperature range -40 C – +60 C Type I and type ll cable glands are suitable for unarmored cable; type Ill and type IV cable glands are suitable for armored cable. Type V cable gland is used for shielded cable entry. Assorted mounting and gland accessories available – refer to catalog

View Complete Details

Ac Contactors

AC Contactors Explosion protection to -CENELEC -IEC -NEC Can be used in Zone 1 and Zone 2 Class I, Zone 1 and Zane 2 Class I, Division 2, Groups A, B, C, D Product of flame-proof structure; the cavity is of engineering plastic embedded with high strength metal frame structure; with strong corrosion-proof capacity and reliable performance; Built-in Schneider AC contactor with 3 pairs of main contacts and as many as 4 pairs of auxiliary contacts for easy for wiring.  

View Complete Details

Aluminium Alloy Bushings

Aluminium Alloy Bushings Explosion protection to -CENELEC -IEC -NEC Can be used in Zone 1 and Zone 2 Zone 21 and Zone 22 Class I, Zone 1 and Zone 2 Class I, Division 2, Groups A, B, C, D Ex e enclosure, copper-free aluminium. powder coated surface. Widely used for connection in steel pipe wiring system  

View Complete Details

Ammeters / Voltmeters

Explosion protection to -CENELEC -IEC -NEC Can be used in Zone 1 and Zone 2 Zone 21 and Zone 22 Class I, Zone 1 and Zone 2 Class I, Division 2, Groups A, B, C, D Fast comparison of measured and set values Versions available -Ammeter (type 72) -Voltmeter (type 72)

View Complete Details

CABLE GLANDS UNARMORED SINGLE SEAL

Cable Glands – Unarmored Single Seal Explosion protection to -CENELEC -IEC -NEC Can be used in Zone 1 and Zone 2 Zone 21 and Zone 22 Class I, Zone 1 and Zone 2 Class I, Division 1, Groups A, B, C, D Ex d, Ex e structure; available in stainless steel, nickel plated brass or galvanized carbon steel. Single seal, suitable for unarmored cable

View Complete Details

CAST IRON BUSHINGS

Cast Iron Bushings Explosion protection to -CENELEC -IEC -NEC Can be used in Zone 1 and Zone 2 Zone 21 and Zone 22 Class I, Zone 1 and Zone 2 Class I, Division 2, Groups A, B, C, D Ex e enclosure, cast iron, powder coated surface. Widely used for connection in steel pipe wiring system  

View Complete Details

Tell Us What are you looking for? Will call you back

Contact Us

  • Mr. Aneeshkumar M. Pillai
  • Executive Suite Z 2 – 15, SAIF Zone, Post Box 121477 SHARJAH, UNITED ARAB EMIRATES, Sharjha, United Arab Emirates