Other Products / Services #5173210

PHILIPP Sandwish Panel Anchor System has several advantages:Reduction of mounting and planning effortMinimal thermal bridge through the fastening systemUse of high quality stainless steel in anchor for lasting corrosion resistanceUniform load transfer in thin-walled elements through load balancing between several support anchorsSimple system adjustment even for geometrically complicated elementsInsulating layer thickness up to 20cm possibleConnector pins can be used without further calculation under observation of the default boundary conditionsStructural standard accounts for wind load as well as stress from temperature changes and shrinkageThe inspected system does not restrict the progress of the construction workComprehensible and simple installation of anchors and pins

PHILIPP Lifting Insert is a lifting insert with cross hole with threads on both sides. Once used, attention must be paid to the general instruction for installation and use. PHILIPP Lifting Inserts are used for transport of precast concrete units. The insert may only be used with PHILIPP devices.

PHILIPP Swivel Lifting Device consists of a forged ring bolt with a chain link and a bottom part made of special hardened steel. The inside construction consists of a bearing inlay. The use of PHILIPP Swivel Lifting Device in a sunk position with nailing plates with too small diameters is inadmissible. Because of its ball-bearing, the hanger moves after achievement of the nominal load bearing itself into the right force direction without removing the bottom part of the Philipp Swivel Lifting Device.

PHILIPP Recess Former are used to fix PHILIPP threaded anchors, PHILIPP threaded inserts and PHILIPP lifting inserts onto the mould. The existing nail holes allow a fixation with nails. The application of PHILIPP Recess Former ensures a rectangular contact area for the compression plate of the Swivel Lifting Devic

PHILIPP Connecting Loops are used for structural connections of precast units loaded by primarily static shear forces. The loops transfer shear forces where no approval is required. PHILIPP Connecting Loops are very flexible and form a connection due to the overlapping of the loops. Therefore, it is possible to easily realize even complicated connections. PHILIPP Connecting Loops can be used without additional proofs. The simple installation ensures practical application. PHILIPP Connecting Loop is a connecting element for the form closed connection of precast units. The flexible loops have the advantage that no reverse bending is required and hence the installation of precast units between columns is realizable. PHILIPP Connecting Loop consists of a plastic or galvanized steel recess former and is suitable for reinforced concrete and light weight concrete.

PHILIPP Hole Anchor System consists of a steel component insert into the concrete (the anchor) and a lifting component (the ring clutch). The precast unit is lifted and transported by means of a ring clutch, which is locked to the anchor cast into concrete. The design and shape of the ring clutch and anchor enable the lifting of the load in almost any load direction. The ring clutch can be unlocked either manually, direct at the clutch head, or by remote release

PHILIPP Spherical Head Lifting Clutch is constructed in a way that an unintended coupling off (even without tension by a lifting device) is impossible. On lifting, attention must be paid that the lip shows into the direction of tension. PHILIPP Spherical Head Lifting Clutch is suitable for all directions (axial, diagonal and lateral tension). Coupling onoff can be made easily with one hand. This clutch may be used in combination with the original PHILIPP Spherical Head Transport Anchor.

Fixing Sockets (also called Cast-In Sockets), have an internal thread and a cross hole on the flat-crimped end. Fixing Sockets are used to transport precast concrete units

Bolts, Nuts & Washers are available in different standards, finishes and sizes. DIN STANDARDS BOLTSNUTSWASHERSDIN 931 (Partial Thread)Hex Bolts Grade 8.8DIN 934 Hex Nuts Grade 8DIN 125 DIN 127 Flat Round Washers Spring Lock WashersDIN 933 (Full Thread) Hex Bolts Grade 8.8DIN 934 Hex Nuts Grade 8DIN 125 DIN 127 Flat Round Washers Spring Lock WashersDIN 6914 H.S.Hex Bolts Grade 10.9DIN 6915 H.S Hex Nuts Class 10DIN 6916 Hardened Flat Washers Coating: Black, Electro Galvanized, Hot Dip Galvanized for all standards except for DIN 6914 which is only supplied in Black. Coating of DIN 6914 is not recommended.

Direct Tension Indicators (DTIs) are recognized by many engineers as the most reliable method for ensuring correct installation of high strength bolts according to that specification for both shear bearing connections requiring fully pretensioned bolts. DTIs are simple and extremely accurate devices for ensuring that bolts have been installed above the specified minimum tension value

Expansion Bolts, also called Wedge Anchors are used to anchor fixtures into concrete. They work by inserting them into a hole drilled into concrete. The Wedge Anchor is then expanded, wedging itself securely in the concrete. They are available in Stainless Steel Grade 304, Stainless Steel Grade 316, Zinc Plated Carbon Steel.

We can supply a big variety on anchors: J Anchors L Anchors U Anchors Straight Anchors Metal Cavity Anchors And many others For "J", "L", "U" anchors, send us your detailed enquiries with drawings and we'll send you our offer.

The BS EA & BS EASF are 2-component reaction resin mortars based on epoxyacrylate for the BS EA and a styrene-free epoxyacrylate For the BS EASF and will be delivered in a 2-C cartridge system. This product may be used in combination of a hand-, battery-, or pneumatic tool and a static mixer. It was designed as a cost effective alternative for the anchoring of threaded rods and internal threaded rod sleeves for approved applications. By using a screen sleeve, an easy and safe application in hollow bricks is guaranteed. The BS EA & BS EASF products are characterized by good applications with an ambiance temperature up to 80C.

Fully integrated stud welding systems having two digital controls for time and current. TRU-WELD stud welding machines were designed to meet the most challenging stud welding jobs including thru-deck applications. A complete system includes: * Power supply controller The machine* TWE 17000 heavy duty stud gun* 50 ft (15 meters) of 40 weld and control cable* 25 ft (7.5 meters) of 40 ground cable with HD clamp* Trolley

MULTI AS is a compact stud welding machine for drawn arc stud welding. This handy, powerful stud welding machine can be used for universal application, it is compact, robust and ideal for field use. Used for welding elements according to DIN 32500 and DIN 32501 and special metallic shaped parts of alloyed and unalloyed steel, the machine can be provided with an inert-gas control, so that ferrule is not necessary for welding. Depending on the particular application, special damped or un-damped guns are available with suitable ferrule support, inert-gas support or support for short-cycle welding guns with or without automatic length compensation.

TRU-WELD offer a wide range of shear studs covering the majority of studs requirements. Studs are available in several diameters and lengths. The length of the stud is reduced approximately 18 to inch during the welding operation, this change must be considered when selecting a stud to fit a particular application. TRU-WELD studs are manufactured from ASTM A-108 Grades 1010 thru 1020 steel, which conforms to the applicable A.W.S. and I.C.B.O. standards. All TRU-WELD studs are supplied with ceramic ferrules designed for use with the particular fastener ordered. Ferrules are specially designed of ball clay and talc, an excellent material to withstand heat shock as well as reasonably high temperatures without melting or breaking. TRU-WELD ferrules complement the perfect position arc initiator and the uniform flux load to effect a top quality weld.