Our Products #1848098

L&T Metering offers flush mount versions of its electronic meters, which can be used in panels for non-tariff energy measurement and for load control. We have a wide range of panel meters for sub-metering and load monitoring purposes.

MG30 MG30-I is Multifunction Microprocessor Relay for protection of mediumlarge synchronous generators. The relay measures the RMS of three-phase currents and voltages and computes the positive and negative sequence components of the Current system.Salient Features:Voltage-controlled overcurrent protectionThermal image element with prealarm levelReverse power protectionLoss of Field protectionPT s' fuse failure protection Modbus Communication Protocol Breaker Failure protectionInadvertent CB closure protectionBlocking Output and Blocking Input for pilot wire selectivity coordination

L&Ts high accuracy availability based tariff (ABT) meters provide a flexible solution for energy monitoring and billing bulk inter utility power flows.Features:Class 0.2s accuracy3 Phase 4 WireConforms to IEC and IS standards15 minute block average for frequency and energyFrequency coding for billingSeparate reactive energy registers linked to supply voltageMidnight storage of energiesLoad SurveyOptical portRS 485 communication (optional)

1 Phase MeterAll Products101+101+1 Phase MeterThis compact EM101+ single phase meter fits snugly into any meter box. The bright back-lit display ensures ease of reading.Features:Class 1 accuracy as per IS and IEC standardsForward energy recording irrespective of current directionIndication for power on, current reversal and ELTReset backupsMulti-tariff Time of the Day meteringHigh surge withstand capabilityLoad Survey (Interval Data)Anti-tamper featuresOptical portRS 232 portLow Power Radio (optional)

RPM14 Reactive Power ManagerAll Productsrpm814rpm814Reactive power manager is designed for automatic control of capacitor banks in 3 phase 4 wire LT distribution systems.The relay maintains the system power factor at a set value, under fluctuating load conditions, by connecting or disconnecting capacitor banks to the 415V bus.Features:Automatic CK ratio selectionPower Factor correction up to 1% of rated current14 capacitor banksProgrammable CT ratio and capacitor bank valuesVoltage, current and reactive power display

nX Series offer you numerical type 3 phase overcurrent & Earth Fault Relay. Its microcontroller based design offers you to choose from various field selectable IDMT & definite curves.

SC14S is a self-powered, single-phase, non-directional, Earth fault relay with one measuring element.Salient featuresMicro-controller based designDraw out facilityBuilt in Third Harmonic Filter.It helps to avoid spurious tripping in harmonic rich power systemsInstantaneous time delay or delay of 100 ms, 200 ms can be setCurrent Input: 1A 5AApplicationThe relay can be used for differential protection of generators, REF applications of generators and transformers in all low voltage, medium voltage sub-stations.

Nova Multifunction MeterAll ProductsNovaNovaThis panel meter measures voltage, current and kWh energy in a 3 phase 4 wire system. The meter has an LCD display with backlight, thus enabling ease of reading.Features:Class 1 accuracyACDC auxiliary supplyRS 485 communicationPassword protected CTPT value programming

Acrux - Counter Type MeterAll ProductsAcruxAcruxThis counter meter is used in control panels to measure kWh energy. This product is available in both LT and HT models.Features:Class 1 accuracykWh measurement1A and 5A current ratingPulse LED outputTerminal covers with sealing provision

Arc flash mishaps are highly probable in electrical switchboards especially since they may be caused by rodents or falling tools. An arc flash causes huge damage to the switchboard as well as injury to the operating personnel in a very short time of about 150 milliseconds. This damage can be minimised if the system is tripped within 100 milliseconds of the occurrence of arc before significant energy is developed. Hence an arc flash protection system is a necessity in every electrical switchboard, to ensure operator safety and to minimise the damages associated with an arc flash event. We, at L&T have always tried to give more protection to customer & their investments. PGR-8800 a new arc flash protection is designed to react in a least possible time to avoid mishaps.