Post Buy Requirement
LF
sharjah, United Arab Emirates
Add Review

Physiotherapy Products & Equipment #5818648

Round Sling

SuperMax Round Sling is made of Ultra High Molecular Weight Polyethylene (UHMWP) yarn covered by durable nylon cover to make high performance lifting round slings. While designed SuperMax Round Sling, our goal was lightest lifting gear with higher breaking strength of wire rope. DSR used our long experience of designed and manufacturing know-how's to make SuperMax Round Sling with low elongation while it is stronger than wire rope with less than 10% weight of wire rope. Low elongation SuperMax Round Sling makes lifting job much easier and safer. Low elongation enables very lash back. Also, SuperMax Round Sling is very stable when used with hook, and you can avoid rotating problem of wire rope slings.

 

SuperMax® Round Sling Steel Wire Rope Sling
Weight 1/10 of wire rope of same breaking strength. Light weight enables easy installing and handling of sling, and higher productivity of lifting job. Because of heavy weight, it's very difficult to move and install the slings. Heavy wire rope sling can cause back pain of the users.
Stability Do not damage the material to be lifted. Positioning is fast and easy. Can tighten up the material to avoid slip while lifting the products. Can hurt the material to be lifted. Positioning is slow and difficult.
Durability Durable against chemical contacts. Because of the flexibility, its bending ratio can be far smaller. Easy to get rusted against acid or alkali. Because of stiffness, broken wire can occur unless extra care is taken.
Storability Only small storage space is required because of its flexibility. Large and dry storage space is required.
Economical Value High initial investment cost. However, higher productivity, longer service life, easier handling and storage result in low total operating costs. Low initial cost. However, more manpower and heavier equipments to move, install, and lift are required. Total operating cost is high.

 

 

 

MARK SPECIFICATIONS
SWL (Safe Working Load)(KG) Working Load Limits Safety Factor
7 : 1 Breaking Strength (KG)
Vertical Choker 45° 60° Basket
1,000 1,000 800 1,400 1,000 2,000 7,000
2,000 2,000 1,600 2,800 2,000 4,000 14,000
3,000 3,000 2,400 4,200 3,000 6,000 21,000
4,000 4,000 3,200 5,600 4,000 8,000 28,000
5,000 5,000 4,000 7,000 5,000 10,000 35,000
6,000 6,000 4,800 8,400 6,000 12,000 42,000
8,000 8,000 6,400 11,200 8,000 16,000 56,000
10,000 10,000 8,000 14,000 10,000 20,000 70,000
15,000 15,000 12,000 21,000 15,000 30,000 105,000
20,000 20,000 16,000 28,000 20,000 40,000 140,000
25,000 25,000 20,000 35,000 25,000 50,000 175,000
30,000 30,000 24,000 42,000 30,000 60,000 210,000
35,000 35,000 28,000 49,000 35,000 70,000 245,000
40,000 40,000 32,000 56,000 40,000 80,000 280,000
 
 
 
 
SuperMax® ROUND SPECIFICATIONS
SWL (Safe Working Load)(KG) Working Load Limits Safety Factor
6 : 1 Breaking Strength (KG)
Vertical Choker 45° 60° Basket
1,000 1,000 800 1,400 1,000 2,000 6,000
2,000 2,000 1,600 2,800 2,000 4,000 12,000
3,000 3,000 2,400 4,200 3,000 6,000 18,000
4,000 4,000 3,200 5,600 4,000 8,000 24,000
5,000 5,000 4,000 7,000 5,000 10,000 30,000
6,000 6,000 4,800 8,400 6,000 12,000 36,000
8,000 8,000 6,400 11,200 8,000 16,000 48,000
10,000 10,000 8,000 14,000 10,000 20,000 60,000
15,000 15,000 12,000 21,000 15,000 30,000 90,000
20,000 20,000 16,000 28,000 20,000 40,000 120,000
25,000 25,000 20,000 35,000 25,000 50,000 150,000
30,000 30,000 24,000 42,000 30,000 60,000 180,000
35,000 35,000 28,000 49,000 35,000 70,000 210,000
40,000 40,000 32,000 56,000 40,000 80,000 240,000

 

 

View Complete Details

Hyperlock Slings

Features
Made in-house at our hamriyah free zone facility to a stringent quality plan
Typical construction of 7x (6x36WS + IWRC)
Manufactured in accordance with IMCA M 179 Rev.1
Flemish eye resign filled sleeve termination (ferfst) with 100% termination efficiency which results in high breaking
Consistency in sling lengths
Can be manufactured in long lengths and even in very short lengths thus having advantage over cable laid slings
Improved load distribution due to FERFST method
No tail end protrusion making it safer to use
Ease of handling
View Complete Details

Round Jacket Sling

SuperGuard
SuperGuard as method of perfect protection could be applied to SuperMax Rope as well as SuperMax Roundsling. SuperGuard will prevent SuperMax Rope as well as SuperMax Roundsling from abrasion and the life time of ropes and sling will be longer with perfection.
SuperGuard-SW2
SuperGuard-AW2
SuperGuard-SAW
SuperGuard-SNW

SuperGuard-NW2

Safety Self-Check Sling
Safety Self-Check sling with Ultra High Molecular Weight Polyethylene(UHMWPE) could check the life time of SuperMax Round Sling.
Melting Point : 150C
Temperature Range for USE : -40C to 70C
Elongation at Break : 4 5%
Specific Gravity : 0.97 (Float)
Water Proportion : None (Wet strength equals Dry strength)
Strongest fiber rope, maximum strength to weight ratio and strength comparable to steel wire rope
View Complete Details

Chain Slings & Grade

Features
More than 250 tons of Grade 100 & Grade 80 chain in stock
Upto 32mm lifting chain in stock
Chains manufactured to EN 818-1 and Chain Slings to EN 818-4

Fittings from Crosby, GN Rope Fittings, ToyoLift, Van Beest - Green Pin

Head Room:

The distance between the crane hook and the load is known as the "Head Room". If a specific head room is required the "Reach" of the chain sling must increase as the angle between the legs increases as shown below (left).

Reach or Effective Working Length (EWL):
The reach of a chain sling is the distance between bearing points of the upper and lower terminal fittings. This distance, commonly known as the "Effective Working Length" should be quoted when ordering slings. Shortening clutches may be fitted to a sling, making the reach adjustable, hence increasing the versatility of the sling.
View Complete Details

Part Braided Slings

Features
Made in-house at our hamriyah fee zone facility to a stringent quality plan
liftx 9 part braided slings are manufactured in a 9 strands configuration
Fabricated in 9x (6x36WS + IWRC), Tensile Strength 1, 960 N/mm2, EEIPS
Slings upto 2050 MT CSBL
Standards in place to ensure effective working length tolerance
Manufacture to ASME B30.9, wire rope technical board, IMCA 179 standards
Greater flexibility, reduced weight and non-twisting characteristics
Increased number of ropes in the eye and leads to higher efficiency by parallel positions of unit ropes in the sling eye
Terminated using flemish eye and steel ferrule
Supplied with in-house test certificate, 3rd party certification from DNV-GL, ABS, BV, TUV etc available upon request
View Complete Details

Steel Wire Rope Slings

Features
One of the most comprehensive rigging facilities in the Middle East
Fabrication of slings upto 4 inch (103mm) diameter with Steel (Flemish) and Aluminum sleeves
Slings manufactured to EN 13414-1
Fittings from Crosby, GN Rope Fittings, Rope Block, Rocon, Wirop, ToyoLift, Green Pin

Nominal Rope Dia (mm) WORKING LOAD LIMITS (Tonnes)
  8 (5/16")
0.82 1.15 0.82 1.72 1.23
  9  
1.00 1.40 1.00 2.10 1.50
  10 (3/8")
1.30 1.80 1.30 2.73 1.95
  11  
1.50 2.10 1.50 3.15 2.25
  12  
1.80 2.50 1.80 3.80 2.70
  13 (1/2")
2.10 2.90 2.10 4.40 3.15
  14 (9/16")
2.50 3.50 2.50 5.25 3.75
  16 (5/8")
3.30 4.60 3.30 6.90 4.95
  18  
4.10 5.70 4.10 8.60 6.15
  19 (3/4")
4.60 6.40 4.60 9.65 6.90
  20  
5.10 7.10 5.10 10.70 7.65
  22 (7/8")
6.20 8.70 6.20 13.00 9.30
  24  
7.40 10.30 7.40 15.50 11.10
  26 (1")
8.60 12.00 8.60 18.05 12.90
  28 (1-1/8")
10.00 14.00 10.00 21.00 15.00
  32 (1-1/4")
13.10 18.30 13.10 27.50 19.65
  36 (1-3/8")
16.60 23.20 16.60 34.85 24.90
  38 (1-1/2")
18.50 25.90 18.50 38.85 27.75
  40  
20.60 28.80 20.60 43.25 30.90
  42 (1-5/8")
22.60 31.60 22.60 47.45 33.90
  44 (1-3/4")
24.80 34.70 24.80 52.10 37.20
  48 (1-7/8")
29.50 41.40 29.50 61.95 44.25
  52 (2")
34.80 48.70 34.80 73.10 52.20
  56 (2-1/4")
40.20 56.30 40.20 84.40 60.30
  60  
46.20 64.70 46.20 97.00 69.30
  64 (2-1/2")
54.80 76.70 54.80 115.10 82.20
  71 (2-3/4")
66.60 93.20 66.60 139.85 99.90
  76 (3")
76.50 107.10 76.50 160.65 114.75
  83 (3-1/4")
89.60 125.50 89.60 188.20 134.46
  89 (3-1/2")
101.00 141.40 101.00 212.10 151.50
  103 (4")
129.00 180.60 129.00 270.90 193.50
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • Liftek FZC (Liftek FZC)
  • P.O. BOX : 41850, Hamriyah Free Zone, Sharjah, UAE
  • Share us via