M.Husain & Bros LLC

United Arab Emirates

• Positive Lock Latch is Self-Locking when hook is loaded.Forged Alloy Steel - Quenched and Tempered.Rated for both Wire Rope and Grade 80 Chain.Meets ASTM A-952-96 and proposed Euronorm standards for Grade 80 chain fittings.Fatigue rated.The SHUR-LOC hook, if properly installed and locked, can be used for personnel lifting applications and meets the intent of OSHA Rule 1926.550 (g) (4) (iv) (B).G-414 Heavy Thimble should be used with wire rope slings.Individually Proof Tested at 2-1/2 times the Working Load Limit with certification.Trigger repair Kit available (S-4316). Consist of spring, roll pin and trigger.Designed with Engineered Flat to connect to Grade 80 chain fittings."Look for the color Gold - Crosby Alloy Hooks".

• Forged alloy heat treated hooks.Forged steel swivel tees, yokes and shackles.Hook and shackle assemblies on 4-1/2" through 14"sizes can be interchanged.Can be furnished with bronze bushings or roller bearings.Opening feature permits insertion of rope while block is suspended from gin-pole.3" thru 18" 418 and 419 blocks have exclusive bolt retaining spring to assure no lost bolts.Can be furnished with S-4320 hook latch.Pressure lube fittings.3" - 10" feature dual rated wireline sheaves.Fatigue rated.4-1/2" and larger are RFID EQUIPPED.

• Hook is Forged Alloy Steel - Quenched and Tempered.Individually Proof Tested at 2-1/2 times the Working Load Limit with certification.Integrated heavy duty latch.Large throat opening.Anti-fouling due to carefully designed contours.Meets ASTM A-952-96 and proposed Euronorm standards for Grade 80 chain fittings.Fatigue rated."Look for the color Gold - Crosby Alloy Hooks."

• Forged Alloy Steel - Quenched and Tempered.Individually Proof Tested at 2-1/2 times the Working Load Limit with certification.Recessed trigger design is flush with the hook body, protecting the trigger from potential damage.Easy to operate with enlarged thumb access.Positive Lock Latch is Self-Locking when hook is loaded.Rated for both Wire Rope and Grade 8 Chain.G-414 Heavy Thimble should be used with wire rope slings.Trigger repair Kit available (S-4316). Consists of spring, roll pin and trigger.S-3326 Swivel Hook utilizes anti-friction bearing design which allows hook to rotate freely under load.Fatigue rated.The SHUR-LOC hook, if properly installed and locked, can be used for personnel lifting applications and meets the intent of OSHA Rule 1926.550 (g) (4) (iv) (B)."Look for the color Gold - Crosby Alloy Hooks".U.S. Patent 5, 381, 650 and foreign equivalents.

• Available in capacity of .5 metric tons.Jaw openings available: IPDV - 11.75" IPVK - .63"Welded alloy steel body for strength and smaller size. Forged alloy components, where required.Individually Proof Tested to 2 times the Working Load Limit with certification.Company name (IP), logo, Working Load Limit and jaw opening permanently stamped on body.Each product is individually serialized, with the serial number and Proof Load test date stamped on body. Serial number is included on the test certificate with maintenance and warranty logbook.Maintenance replacement parts are available.Manufactured by a ISO 9001 facility.IPDV is RFID EQUIPPED.

• BARS OF JAPANESE ORIGIN
• ALL BARS ACCOMPANIED BY MANUFACTURERS TEST CERTIFICATE
• SIZES FROM 3/8" DIA TO 3" DIAM IN LENGTHS OF 3 METERS

• PLATES OF JAPANESE ORIGIN
• SIZES FROM 0.5mm THICK TO 25.0mm THICK
• DIMENSIONS OF PLATES ARE EITHER 1MTR X 2MTR OR 4" X 8"
• ALL PLATES ACCOMPANIED BY MANUFACTURERS TEST CERTIFICATE

• IN GRADES OF 304, 316, & 316 L
• ROUND BAR IN SIZES OF 6mm TO 350mm IN LENGTHS OF 4METERS OR 6 METERS
• HEX BARS AND SQUARE BARS IN SIZES FROM 13mm A/F TO 50mm A/F IN RANDOM LENGTHS OF 3 TO 4 METERS
• ALL BARS ARE OF JAPANESE / GERMAN ORIGIN AND ARE ACCOMPANIED BY A TEST CERTIFICATE

• IN GRADES OF 304, 316, 316L
• PLATE SIZES FROM 5mm TO 50mm
• FLAT BARS FROM 25mm X 3mm TO 150mm X 12mm IN LENGTHS OF 4 MTRS, 5 MTRS OR 6 MTRS
• ANGLES ARE IN GRADE 304 ONLY AND SIZES VARIE FROM 25mm X 25mm X 3mm X 6 MTRS TO 4" X 4" X 1/2" X 6 MTRS
• ALL BARS ARE OF JAPANESE / GERMAN ORIGIN AND ARE ACCOMPANIED BY A TEST CERTIFICATE

• ALSO AVAILABLE EX-STOCK ARE STAINLESS STEEL CHANNLES IN GRADE 304
• THESE CHANNELS ARE OF JAPANESE ORIGIN AND ARE TEST CERTIFIED

• RANGING FROM DIA 1/4" OR 6mm UPWARD TO 10" OR 250mm DIAMETER IN LENGTHS OF UPTO 3 MTRS
• ALL BARS ARE EITHER MANUFACTURED IN NEW ZEALAND / AUSTRALIA OR JAPAN
• TEST CERTIFICATES ARE PROVIDED WITH EACH PURCHASE

• A COMPREHENSIVE RANGE OF SIZES ARE AVAILABLE IN BOTH FLAT BARS AND ANGLES
• THE SPECIFICATION OF JIS H3250, 3604 BE, MAKES THEM SUITABLE FOR A WIDE SPECTRUM OF USES FROM ENGINEERING TO DECORATIVE
• AS EACH ORDER IS FULLFILLED WITH THE RELEVENT TEST CERTIFICATES

• INVENTORY IN THIS ITEM RANGES FROM A SIZE OF 3/8" TO 3"
• WALL THICKNESSES OF 1.5mm FOR THE SIZE UPTO 1" AND 2.0mm FOR SIZES FROM 1" TO 3"
• MATERIAL IS OF AUSTRALIAN / JAPANESE ORIGIN AND WILL BE SUPPLIED WITH TEST CERTIFICATES

• MANUFACTURED IN JAPAN, THESE ARE AVAILABLE IN BOTH GUAGE AND MILLIMETER SIZES RANGING FROM 0.5mm TO 25mm IN DIMENSIONS OF 1m X 2m AND 4' X 8'

• RANGING FROM DIA 1/4" OR 6mm UPWARD TO 10" OR 250mm DIAMETER IN LEMGTHS OF UPTO 3 MTRS
• ALL BARS ARE OF JAPANESE/AUSTRALIAN/NEW ZEALAND ORIGIN AND TEST CERTIFICATES WILL BE PROVIDED FOR EACH SIZE

• IN OUR STOCK WE HAVE A WIDE RANGE OF HOLLOW BARS FROM ODS OF 50mm TO 450mm WITH A RANGE OF DIFFERENT INTERNAL DIAMETERS
• DIAMETERS AND THESE BARS LENGTHS ARE IN LENGTHS FROM 4MTRS FROM SMALL DIAMETERS TO 1 METER FOR LARGE DIAMETERS
• ALL BARS ARE OF AUSTRALIAN/NEW ZEALAND ORIGIN AND ARE TEST CERTIFIED

• BARS FROM DIA: 1/4" TO 20 1/4"
• MINIMUM LENGTH OF PURCHASE IS 1FT FOR ALL LENGTHS
• FULL LENGTHS RANGE FROM 3 MTR TO 6 , TRS
• ALL BARS ARE OF JAPANESE / U.K. ORIGIN WITH MANUFACTURERS TEST CERTIFICATE

• BARS FROM 12mm TO 25mm
• MINIMUM LENGTH OF PURCHASE IS 1FT FOR ALL LENGTHS
• FULL LENGTHS RANGE FROM 3 MTR TO 6 MTRS
• ALL BARS ARE OF JAPANESE / U.K. ORIGIN WITH MANUFACTURERS TEST CERTIFICATE

• BARS FROM 12mm TO 250mm
• MINIMUM LENGTH OF PURCHASE IS 1FT FOR ALL LENGTHS
• FULL LENGTHS RANGE FROM 3 MTR TO 6 MTRS
• ALL BARS ARE OF JAPANESE / U.K. ORIGIN WITH MANUFACTURERS TEST CERTIFICATE

• WE CAN PROVIDE YOU WITH A RANGE OF OTHER BARS INCLUDING MONEL AND INCO ALLOY ALL OF WHICH CAN BE SUPLIED WITHIN A WEEK FROM THE DATE OF ORDER

• THREADED BARS AND HEX NUTS CONFIRMING TO ASTM A 193 B7 FOR STUDS AND ASTM A 194 2H FOR NUTS
• BARS ARE AVAILABLE IN LENGTHS OF 12 FT FOR THREADED STUD BARS FROM 3/8" DIA TO 4" DIAMETER
• LENGTH CAN BE CUT ACCORDINGLY TO YOUR REQUIREMENT
• BARS CAN BE DELIVERED IN SELF-COLOR OR IN CADMIUM PLATED OR QUOTED WITH FLUORO CARBON
• WE ALSO HAVE FACTORY CUT SIZES UPTO 1.1/2" DIAMETER THESE BARS ARE AVAILABLE IN RANDOM LENGTHS
• ALL STUDS / NUTS / WASHER ARE FROM FRANCE / U.S.A. / U.K. ORIGIN AND WILL BE DELIVERED WITH TEST CERTIFICATES

• AVAILABLE IN GRADES OF 8.8 OR 10.9
• DIAMETERS FROM 20MM TO 64MM IN VARIED LENGTHS
• ALL BOLTS / NUTS DELIVERED WITH RELEVENT TEST CERTIFICATES
• SS FASTERNERS IN GRADES OF 304, 316 & 316L
• DIAMETERS FROM 20mm TO 39MM IN VARIOUS LENGTHS
• ALL STUDS / NUTS / WASHER ARE FROM FRANCE / U.S.A. / U.K. ORIGIN AND ARE WILL BE DELIVERED WITH RELEVANT TEST CERTIFICATES

• CHAIN BLOCK FROM MOVE IT HOLLAND AND VITAL JAPAN ARE AVAILABLE FROM STOCK
• SIZES RANGE FROM 0.5T TO 20T WITH STANDARD CHAIN LENGTHS
• LONGER HAND CHAINS AND LOAD CHAINS ARE AVAILABLE ON REQUEST
• ALL CHAIN BLOCKS WILL DELIVERED TEST CERTIFICATE

• LEVER HOISTS FROM 0.75T TO 6T WITH STANDARD CHAIN LENGTHS IOF 1.5 METERS
• LEVER HOISTS WILL BE DELIVERED WITH TEST CERTIFICATES

• FROM 0.8T LIFTING TO 3.2T LIFTING-STANDARD WIRE ROPE OF 20 METERS
• NON STANDARD WIRE ROPE LENGTHS ARE AVAILABLE ON REQUEST
• CERTIFICATES PROVIDED WITH MATERIAL

Forged Alloy Steel - Quenched and Tempered.
Individually Proof Tested at 2-1/2 times the Working Load Limit with certification.
Recessed trigger design is flush with the hook body, protecting the trigger from potential damage.
Easy to operate with enlarged thumb access.
Positive Lock Latch is Self-Locking when hook is loaded.
Rated for both Wire Rope and Grade 8 Chain.
G-414 Heavy Thimble should be used with wire rope slings.
Trigger repair Kit available (S-4316). Consists of spring, roll pin and trigger.
S-3326 Swivel Hook utilizes anti-friction bearing design which allows hook to rotate freely under load.
Fatigue rated.
The SHUR-LOC hook, if properly installed and locked, can be used for personnel lifting applications and meets the intent of OSHA Rule 1926.550 (g) (4) (iv) (B).
"Look for the color Gold - Crosby Alloy Hooks".
U.S. Patent 5, 381, 650 and foreign equivalents.

100% termination efficiency.
Temperature operating range is -65 F to +240 F.
Ideal for on site applications.
No hazardous molten metal.
Improved fatigue life.
Pouring temperature without booster pack is 48 F to 110 F.
One booster pack if pouring temperature is 35 F to 48 F.
Two booster packs if pouring temperature is 27 F to 35 F.
Refer to WIRELOCK Technical Manual for more information.

• Wedge socket terminations have an efficiency rating of 80% based on the catalog strength of XXIP wire rope.Crosby products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.Type Approval and certification in accordance with ABS 2006 Steel Vessel Rules 1-1-17.7, and ABS Guide for Certification of Cranes.Basket is cast steel and individually magnetic particle inspected.Pin diameter and jaw opening allows wedge and socket to be used in conjunction with closed swage and spelter sockets.Secures the tail or "dead end" of the wire rope to the wedge, thus eliminates loss or "Punch out" of the wedge.Eliminates the need for an extra piece of rope, and is easily installed.The TERMINATOR wedge eliminates the potential breaking off of the tail due to fatigue.The tail, which is secured by the base of the clip and the wedge, is left undeformed and available for reuse.Incorporates Crosbys patented QUIC-CHECK "Go" and "No-Go" feature cast into the wedge. The proper size rope is determined when the following criteria are met:1) The wire rope should pass thru the "Go" hole in the wedge.2) The wire rope should NOT pass thru the "No-Go" hole in the wedge.Utilizes standard Crosby Red-U-Bolt wire rope clip.The 3/8" thru 1-1/8" standard S-421 wedge socket can be retrofitted with the new style TERMINATOR wedge.Available with Bolt, Nut, and Cotter Pin.U.S. patent 5, 553, 360, Canada patent 2, 217, 004 and foreign equivalents.

• Each base has a Product Identification Code (PIC) for material traceability, the name CROSBY or CG, and a size forged into it.Based on the catalog breaking strength of wire rope, Crosby wire rope clips have an efficiency rating of 80% for 1/8" - 7/8" sizes, and 90% for sizes 1" through 3-1/2".Entire Clip-Galvanized to resist corrosive and rusting action.Sizes 1/8" through 2-1/2" and 3 have forged bases.All Clips are individually bagged or tagged with proper application instructions and warning information.Clip sizes up through 1-1/2" have rolled threads.Crosby products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
• Look for the Red-U-Bolt, your assurance of Genuine Crosby Clips.

Alloy Steel
Heat Treated
25% stronger than Grade 80 Alloy Chain
Permanently embossed with CG (Crosby Group) and 10 (Grade).
Finish - Black Thermadep Coating.
Proof Tested at 2 times the Working Load Limit with certification.
Standard container - fiber drum

Capacities 1/3 thru 55 metric tons.
Forged - Quenched and Tempered, with alloy pins.
Working Load Limit permanently shown on every shackle.
Hot Dip galvanized or Self Colored.
Fatigue rated.
Shackles 25t and larger are RFID EQUIPPED.
Shackles can be furnished proof tested with certificates to designated standards, such as ABS, DNV, Lloyds, or other certification. Charges for proof testing and certification available when requested at the time of order.
Shackles are Quenched and Tempered and can meet DNV impact requirements of 42 joules at -20 C.
Crosby products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
Look for the Red Pin . . . the mark of genuine Crosby quality.
Type Approval and certification in accordance with ABS 2006 Steel Vessel Rules 1-1-17.7, and ABS Guide for Certification of Cranes.

Screw pin anchor shackles meet the performance requirements of Federal Specification RR-C-271D Type IVA, Grade A, Class 2, except for those provisions required of the contractor. For additional information, see page 391.

• The most complete line of Eye hoist hooks.Each hook has a Product Identification Code (PIC) for material traceability, along with the size and Crosby & U.S.A. in raised letters.Meets ASTM A-952-96 standards for Grade 80 chain fittings.Suitable for use with Grade 80 chain in overhead lifting applications as long as hook is ProofTested as part of the chain sling assembly or as an individual component. Per ANSI B30.9-1.Forged Alloy Steel - Quenched and Tempered.Engineered Flat for use with S-325A coupler link (thru 5/8").QUIC-CHECK Hoist hooks incorporate two types of strategically placed markings forged into the product which address two (2) QUIC-CHECK features:Deformation Indicators and Angle Indicators (see following page for detailed definition).Fatigue rated to 20.000 cycles at 1.1/2 times the working load limit."Look for the color Gold - Crosby Alloy Products."Can be proof tested to 2-1/2 times the Working Load Limit (4:1).Low profile hook tip.Working Load Limit for Wire Rope forged on raised lettering pad to allow user to grind off quickly and easily without affecting hook.
• • Crosby recommends grinding the Working Load Limit (which is for a 5 to 1 Design Factor) off the hook when using with Grade 80 chain.
• New integrated latch (S-4320) meets the World class standard for lifting.
• • Heavy duty stamped latch interlocks with the hook tip.High cycle, long life spring.When secured with proper cotter pin through the hole in the tip of hook, meets the intent of OSHA Rule 1926.550 (g) for personnel lifting.

• Alloy Steel - Quenched and Tempered.Individually Proof Tested with certification. (See page 138 for proof test values.)Proof Tested with fixture sized to prevent localized point loading per ASTM A952. Consult Crosby for appropriate fixture size.Crosby A-344 products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.Each link has a Product Identification Code (PIC) for material traceability, along with the size and the name Crosby or "CG".Large inside width and length to allow additional room for sling hardware and crane hook.Engineered Flat for use with S-1325A coupler link

• Available in capacities of .5 thru 30 metric tons (Higher Working Load Limits are available upon request).Wide variety of jaw openings available: 0" to 6.13".Welded alloy steel body for strength and smaller size. Forged alloy components, where required.Individually Proof Tested to 2 times the Working Load Limit with certification.Company name (IP), logo, Working Load Limit and jaw opening permanently stamped on body.Each product is individually serialized, with the serial number and Proof Load test date stamped on body. Serial number is included on the test certificate with maintenance and warranty logbook.Available in a variety of styles:
  
  • IPU10 - Standard clamp for materials with a surface hardness to 37Rc (345 HB)IPU10J - Larger jaw opening.IPU10S - For use with Stainless Steel material.IPU10H - For use with materials with a surface hardness to 47Rc (450 HB).
  Full 180 turning range for material transfer, turning or moving.Lock open, lock closed ability with latch for pretension on materialand then release of material.Optional IP-5000 Stinger assembly available (see page 382). Allowsfor easy connection between the clamp and hoist hook.Minimum WLL of 10% of Maximum WLL.Maintenance replacement kits are available.Manufactured by a ISO 9001 facility.All sizes are RFID EQUIPPED.

• Alloy Steel - Quenched and Tempered.Individually Proof Tested at 2-1/2 times the Working Load Limit with certification.The use of A-328 Eye Grab Hook will result in a 20 percent reduction in chain capacity. When used to hook back to chain leg to form a choker, the angle of the choke must be 120 degrees or greater. When used as a chain shortener, minimize twist of chain and ensure chain is fully engaged in hook.

Forged Steel Sockets thru 1-1/2", cast alloy steel 1-5/8" thru 4".
Spelter socket terminations have an efficiency rating of 100%, based on the catalog strength of wire rope. Ratings are based on the recommended use with 6 x 7, 6 x 19 or 6 x 37, IPS or XIP (EIP) , XXIP (EEIP), RRL, FC or IWRC wire rope.

Closed grooved Sockets meet the performance requirements of Federal Specification RR-S-550D, Type B, except for those provisions required of the contractor. For additional information, see page 391.

NOTICE:
All cast steel sockets 1-5/8" and larger are magnetic particle inspected and ultrasonic inspected. Proof testing available on special order.
Drawing illustrates one groove used on sockets 1/4" thru 3/4". Sizes 7/8" thru 1-1/2" use 2 grooves. Sizes 1-5/8" and larger use 3 grooves.