National Plastic & Bldg Matls Industries Llc

national plastic produces a wide range of upvc pressure pipes to most of the major international standards and dimensions of metric and imperial. The pipes are made from 100% virgin upvc resin and have a minimum required strength mrs=25 mpa so that the pipes meet or exceed the rigorous hydrostatic requirements of the standards. The pipes are produced in a range of colours such as grey, white, blue, purple and carry full printing and identification at 1m intervals according to the standard requirements. pipes can be supplied with integral solvent weld joints along with weldon 717 cement or rubber ring joints using high performance epdm seals to en681. The joints exceed the pressure rating of the pipe and can therefore cover all the applications where the pipes are installed. all pipes produced fall under an iso 9001:2008 quality assurance system and several ranges carry third party verification such as the bsi kitemark or wras certification so customers are assured the pipes are of the highest quality. For export requirements pipes can be supplied in 5.8m (19ft) lengths so they can be loaded into containers without damaging sockets. National plastic pressure pipes have been operating in demanding conditions for almost 40 years now (see the worldwide projects list) and is proof of their outstanding quality and serviceablility.

A full range of UPVC and CPVC fittings to the main International Standards of EN1452, BS3505, DIN8063 and ASTM D2466 including sizes from 1/2”-16” (16mm- 400mm). The fittings include solvent weld joints and are fully compatible to the National Plastic pipe range. Specially fabricated fittings and long radius bends can be supplied on request along with rubber ring joints on certain sizes in the range. Fittings are available in standard colours of light grey, dark grey and white and suitable for all pressure applications.

National Plastics produces a range of UPVC pipes for above and below ground use made from 100% virgin UPVC. It has full range of fittings in both solvent weld and rubber ring joint for all sizes. The pipes are produced in all the major international standards ie: European Standards BS EN 1401, BS EN 1329, as well as the previous standards such as BS 5255, BS 4514, BS 4660, BS 5481. A range complying to ASTM D2655 Sch 40/80 is also available on request. National Plastic also has Kitemark licences from BSI for the EN range from 1 1/4" to 16" and can supply Kitemark certified pipes where required. National Plastic can provide a range of fittings from its own Ezyflo brand or from Redi and Hunter. General Properties of National Plastic Drain Pipes Fully compliant to the main International Standards Kitemark certified range Tough, impact resistent EPDM rubber rings following EW681 Standard Can be supplied in Solvent Weld or Rubber Ring Joint (from 3" and above) Different lengths available 3m, 2.9m, 6m, 5.8m. Other lengths on request. Distinctive colour coded system (ie Light Grey, Brown, White, etc.) with full printing at 1m intervals Superior chemical and acid resistance Outstanding mechanical properties of tensile strength and resistance to pressure.

National Plastic produces a range of UPVC Well casing and screens in a range of sizes 1/1/4”-16” (36mm-400mm) to DIN4925 standard. The pipes from which they are made can be either Metric or Imperial dimensions in strict compliance to International Standards and cover shallow or deep well applications. They can be supplied either with flush or socketed type joints and in thread configurations such as BSP, trapezoidal or square type all with varying pitches as required. The casing & screens have a very high tensile strength making them suitable for a wide range of applications and uses including water supply, environmental and land drainage work. In addition to PVC-U material they can also be supplied in HDPE. All the accessories such as lifting heads, end caps, centralisers, casing clamps, sand traps can also be supplied for each size.

National Plastics produces a range of upvc schedule 40 ducts in sizes 1/2" to 6" that are in accordance with NEMA TC-2A standard and listed to UL 651. The conduits are suitable for above or below ground installations and made from 100% virgin pvc resin. The ducts meet and exceed all the mechanical and performance requirement of both the NEMA TC2 and UL 651 standards. General Properties Fully compliant to NEMA TC-2 and UL 651 Rated for use with 90oC conductors Ultraviolet protected High impact and deformation properties Solvent cement joints with deep sockets Can be supplied in various lengths such as 3m, 6m, 2.9m, 5.8m (standard leg lengths 3m, 6m) Smooth solid wall Produced under an ISO 9001:2008 Quality Assurance System

UPVC drainage fittings in either British or Metric / ISO dimensions from size 1 1/4" to 16" (36mm - 400mm). The fittings are suitable for all drain applications including soil, waste, underground and gravity sewer systems. Fittings can be supplied with either rubber ring or solvent socket weld jointing systems. Fittings are available in light grey or brown colours and are compatible with the full range on National Plastic drain pipes.