Our Products
Din 912, ISO 4762, ANSI B18.3.1M
#12.9Din912Socketheadcapscrew #Din912.9AllenBolt #D912AllenScrew12.9
#D912FullythreadedSocketScrew
Socket head cap screws are a headed and externally threaded part designed for insertion through a close tolerance. Tension on the socket cap screw is induced by rotation of the screw head. There is a hex socket in the head that accepts a hex wrench to tighten the socket cap screw. The point at the threaded end of the socket cap screw is machined flat so it will fit into a drilled hole.
Stock range available from M1.6 M52 diameter length from 4mm 300mm.Also available in imperial sizes in UNC / UNF: 3/16 1-1/2.
Brass Wood Screws used in Wood Working Industry, Construction Industry in fixing Doors and Wooden Door Frames etc, In Ship Building as a non-spark product.
HighTensileBoltinDubai #88GradeBoltinDubai
8.8 Grade Bolt In Dubai, UAE
8.8 Grade Bolt In Kuwait
8.8 Grade Bolt In Saudi Arabia
8.8 Grade Bolt In Oman
8.8 Grade Bolt InQatar
8.8 Grade Bolt In Bahrain
DIN 6796Disc Spring Washers Phosphated (Conical Spring Washer)
DIN 2092 Disc Spring Washers (Conical Spring Washer):
Also called Belleville Sping Washers, these are conically-shaped, washer-type components designed to beaxially loaded. What makes Disc Springs unique is that based on the standardizedcalculations of DIN 2092, the deflection for a given load is predictable and theminimum life cycle can be determined. Disc Springs can be statically loadedeither continuously or intermittently, or dynamically subjected to continuous loadcycling. They can be used singly or in multiples, stacked parallel, in series or in acombination thereof.
The advantages of Disc Springs compared to other types of springs
include the following:
A wide range of load/deflection characteristics
High load capacity with small deflection
Space savings high load to size ratio
Consistent performance under design loads
Longer fatigue life
Inherent dampening especially with parallel stacking
Flexibility in stack arrangement to meet your application
requirements
Carriage Bolt Din 603 Available in Steel and Stainless steel
Also called Cup Head Square Neck Bolt andShaker Screen Bolt.CarriageBoltsDesigned for wood-to-wood or wood-to-metal applications, these self-anchoring screws have a square neck to resist turning when the nut is tightened. Its a single handed operation.
Material available inM8 to M36, 5/16 to 1.1/2, Length from25 mm to 400 mm, 1 to 16
#D580LiftingEyeBolt
#D580#LiftingEye#EyeBolt
#Lifting #Eye #Bolt
#SafdariTradersLLC carry high quality CE approved marked European Brand of these products. These are high risk critical fasteners and lives are at risk. DONOT PUT LIVES AT RISK, use our high quality fasteners !
The #lifting #eye #bolts correspond to standard sheet DIN 580.
The following guidelines of lifting eye bolts DIN 580 the have to be observed in addition to the load values given in the above table.
The eye bolt must be of fully screwed in to achieve a perfect contact between the two mating faces. Both threads must be of a equal length and the base material of equal strength to that of the bolt.
Specifications:SteelSTC15 E
D582LiftingEyeNut in Dubai
#Lifting #Eye #Nut
The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table.
The eye nut must be of fully screwed in to achieve a perfect contact between the two mating faces.
SteelSTC15 E
Fin Neck bolts lock into steel or wood surfaces to assist one manbolt tightening.
Also called Round Head Fin Neck Bolt
Available in Yellow Zinc and Hot Dipped Galvanized
L and J Shaped Anchor Bolts (referred to as a type of bent anchor bolts) are used to embed directly into concrete to support a variety of structures including light poles, steel columns, other structures to be fastened to them. The bottom portion that is bent at a 90/120/135 degree angle keeps the bolt from pulling up through the concrete.
These Anchor Bolts are used in many different industries including Steel Erection, Metal Buildings, Light Pole Erection, Steel Tower Erection and many others. We can manufacture Foundation Bolts right here in Dubai UAE. Our Anchors are available in the below diameters, grades and finishes.
Diameters:1/2 through 4
Length:Any Length
Grades: F1554 Grade 55 S1, F1554-Grade 105, A354-BD, A449, A193
Finishes:Plain (black, ) Hot Dipped Galvanized , Electro-galvanised
Security screws (or tamper-proof screws) are easy to install, but are difficult to loosen with a screwdriver.These tamperproof screws can be re-usable (where the screw can be removed and re-installed using the corresponding security tool).Security screws, security bolts, and security nuts are designed so that ordinary tools cannot remove them. Removal can only be accomplished withspecial tools.Anti-theft screws are usually stocked in metric thread
Some common uses of tamper resistant fasteners are: