ZAUN PERIMETER SOLUTIONS

dubai, United Arab Emirates

The HiSec DualSkin double skin 358 mesh fencing system from Zaun, has been specifically designed and developed for applications and sites that require a more robust solution than standard 358 mesh.

This double skin 358 mesh fencing system features two layers of the traditional HiSec 358 welded mesh with 76.2mm x 12.7mm open mesh sections.

These double skin 358 mesh panels are welded together with the secondary panel turned 90 degrees to make a very tight mesh 12.7mm x 12.7mm mesh configuration, which is difficult to cut and almost impossible to climb.

The small apertures of the double skin 358 mesh with welds at each intersection eliminates foot and finger holds for people to climb or gain access to the site.

The tight mesh pattern of the double skin 358 mesh makes it almost impossible to pass objects or contraband through the fence into restricted areasand is highly resistant against the use of hand or power cutting tools.

HiSec DualSkin double skin 358 mesh fencing system provides an ideal solution for a wide variety of high security perimeter, integrated solutions and access control applications. Additional fence toppings can also be used to add extra security to the fence line. Matching pedestrian and vehicle gates are also available to compliment the fence line.

Zauns ArmaWeave woven mesh fencing system is our flagship high security fencing system. Zauns innovative design team have designed its the woven mesh fencing system, Armaweave to secure sites of critical national importance.

Extensively installed on multiple high profile locations around the world, the ArmaWeave woven mesh fencing system has unique system properties, which give significant advantages over other perimeter fencing solutions.

This woven mesh fencing system offers more substantial delays from attack, from hand and powered non-contact tools than would be offered from traditional welded mesh systems thanks to its tighter mesh pattern and use of high tensile steel wires.

The tight woven mesh pattern offers no climbing aids and provides little room for blades and cutting tools to attack the fabric.

ArmaWeave also offers seamless integration with detection systems including PIDs, CCTV and topping enhancements.

• Designed with twin 6mm horizontal wires
• Open mesh pattern provides high visibility to monitor sites without restriction
• High level of vandal resistance
• Available with optional V-Beam (Duo6V) to further increase strength
• Supplied with standard or minimal projections at the top of the panel
• Available either bolt down, in ground or on wall
• For low level fences a safety capping is available
• Available with ZaunFix or Clamp bar fixing options
• Can be supplied in 2.5 (Duo6) or 3mtr (Duo6L) panel widths

• Hostile Vehicle Mitigation temporary fencing solution that achieves PAS 68
• Allows for changes in direction and various ground conditions
• Fence heights of up to 5 metres
• Can be fully integrated with PIDs, CCTV and topping enhancements
• No in ground pinning or foundations required
• Suitable for permanent or temporary installations
• Provides a safe working area protecting the workforce from vehicles travelling next to the site
• Protection for the travelling public from roadside and site hazards
• A safe and effective separation between opposing traffic streams in contraflows, by preventing crossover accidents, whilst maximising available carriageway width due to low deflectionsPrevention for unauthorised vehicle access to site compounds, forecourts, car parks, fields or other property
• A security barrier for protection against vehicle-borne attacks, ram-raiders etc
• Direction and protection for pedestrians or light vehicles in quarries, airports or other industrial, commercial or public areas

FST (Flexible Topping System) security fence topping is the most secure fence topping system available. Developed by the experienced high security development team at Binns Fencing the FST security fence topping is the result of a programme of continuous innovation.

FST security fence topping is a registered design, fully tested and approved by Her Majestys Government for use in high security prisons and mental health units in the United Kingdom. The FST topping uses top quality, specially selected materials, and is manufactured to the very highest standards for long life and long-term reliability.

All materials are galvanised but stainless steel razor wire is recommended to give maximum service life.

At the heart of the security topping is a steel mesh fixed to a flexible steel bracket that is designed to move when people attempt to climb, upsetting balance and hand holds.

The structure is designed to withstand a mans weight, so the FST fence topping system does not collapse when climbed.

The FST Fence Topping is available in four configurations, designed to suit the varying environmental demands of every situation.

• FST Frame Particularly suited to Young Offender Institutions, tests have proven that the FST Frame specification is extremely difficult to climb.
• FST Mono Where height or sight lines are an issue, FST Mono, with its single, lower coil of razor wire attached to the sprung-steel frame is a cost effective solution.
• FST Twin A highly effective solution with two coils of stainless steel razor wire attached to the sprung-steel mesh frame.
• FST Max The ultimate in security topping systems. A sprung-steel, mesh frame and two coils of stainless steel razor wire are linked via motion sensors to an alarm system.

Zauns Terror StopperPAS 68 static bollards are a range of hostile vehicle mitigation (HVM) bollards rated at BSI PAS 68:2010, capable of stopping terrorist vehicle attacks.

These PAS 68 static bollards are designed specifically to be incorporated into our range of perimeter protection systems.

Our selection offers a range of PAS 68 static bollards capable of stopping vehicles at differing speed and vehicle types to suit most site requirements.

Manufactured in four different versions to deal with the various threats and requirements for site of critical national importance. Each of the Terror Stopper bollards have all been independently PAS 68 tested and approved.

• Terror Stopper 1 PAS 68 Static Bollard is a 219mm diameter bollard capable of stopping a 7.5 tonne vehicle at 30 mph. PAS 68:2010 rating of V7500(N2)48/90/0.0/0.0
• Terror Stopper 2 PAS 68 Static Bollard is a 219mm diameter bollard capable of stopping a 7.5 tonne vehicle at 40 mph. PAS 68:2010 rating of V7500(N2)64/90/4.0/16.7
• Terror Stopper 3 PAS 68 Static Bollard is a 273mm diameter bollard capable of stopping a 7.5 tonne vehicle at 40 mph. PAS 68:2010 rating of V7500(N2)64/90/3.3/0.0
• Terror Stopper 4 PAS 68 Static Bollard is a 273mm diameter bollard capable of stopping a 7.5 tonne vehicle at 50 mph. PAS 68:2010 rating of V7500(N2)80/90:10.6/11.1

The Zaun Terror Stopper PAS 68 Bi-Folding Gates consists of a post upon which a bi-folding leaf is hinged on to. Successfully impact tested to PAS 68 stopping a 7.5 tonne vehicle with zero penetration and remained fully functional after impact.

These PAS 68 Bi-Folding Gates are available in either tracked or trackless options. In the trackless option the PAS 68 bi-folding gates do not require any in ground or overhead tracks to fold the gate in half. This gate instead uses an in-house folding system housed inside the casing on top of the post hung leaf. In the tracked option, tracks are installed either over head or in ground to fold the gate in half.

The post hung section is driven by a torque motor driving a crank arm through the 270 degrees giving the gate a good mechanical advantage. The 270 degree drive mechanism together with an electro-magnetic brake, locks the gate in both open and closed positions.

The PAS 68 Bi-Folding Gates are easily interfaced with any access control system and manufactured to a maximum width of 4.2 metres. Each gate can be supplied with aesthetics to suit the environment it is installed.

The Terror StopperCrash Rated PAS 68 cantilever sliding gates are designed to prevent a 7.5 tonne vehicle borne terrorist / ram-raid threat and is capable of blending seamlessly within any building or site perimeter line, enabling discreet vehicle mitigation.

Constructed from steel sections, this gate design can be aesthetically blended into the building or perimeter fencing line. Available with your choice of vertical bar, welded mesh or woven mesh infills ideal for complementing our range of perimeter fencing.

The Crash RatedPAS 68cantilever sliding gatesrequires shallow foundation depths, ideally suited to shallow and / or utility congested substructure.

The product is able to accept any architectural enhancement over and above its standard construction; therefore it lends itself to the continuation of any high security fencing specification, powered fence or security toppings across the normally vulnerable entrance to a site.

The Terror Stopper PAS 68 Mitigate Barrier has been designed and developed as an economical alternative PAS 68 impact tested manual barrier.

This PAS 68 Mitigate Barrier is ideal for location that have frequent vehicle throughput, but still require protection from vehicle borne threats.

The PAS 68 Mitigate Barrier is far more user friendly than manual lift bollards, and requires minimal civil work due to hinge and receptor posts only requiring 215mm foundation depths.

With a clear width availability of up to 10 metres utilising a double leaf format, the PAS 68 Mitigate Barrier is by far the most cost effective, simple PAS 68 compliant solution currently available.

The Terror Stopper PAS 68 PIT Mounted Blocker has been successfully crash tested to PAS 68 specifications. Designed specifically to withstand a hostile vehicle borne improvised explosive device and stop the vehicle dead in its tracks.

The PAS 68 PIT Mounted Blocker has been successfully tested with a 7.5 tonne vehicle at 50 mph.

Ideal for applications where there is plenty of depth to excavate and the sub-surface is free from the path of any buried utilities.

This PAS 68 PIT Mounted Blocker is manufactured and designed to BS 6571: Part 4 1989 with tread plates of 10mm thick (over plain) durbar tread plate.

One piece 3mm thick sheet skirt. The trimmer frames are 70mm x 70mm or 80mm x 80mm hot dip galvanised angle sections fully spragged around the periphery for maximum holding.

The riser frame for this PAS 68 PIT Mounted Blocker are manufactured from heavy gauge RHS sections and fully welded. The base frames are of heavy duty RHS sections designed to withstand axle weights of 15 tonnes.

The retractable automatic Terror Stopper PAS 68 Rising Bollards system is a counter terrorist bollard, hydraulically driven for reliability and strength.

These PAS 68 Rising Bollards have been successfully impact tested as single and dual unit systems stopping 7.5 tonne vehicles traveling at speeds of up to 50 mph 980kph) which eqyates to 1852kJ.

Both impacts resulted in the automatic PAS 68 rising bollards stopping the vehicle within the aperture and remained fully functional.

Static and rising bollards are required to be installed at 1.2 metres between the upright bollard faces to meet the PAS 69 guidelines.

Manufactured with a stainless steel clad as standard, with optional painted powder coating.

The retractable automatic PAS 68 rising bollards have an industrial hydraulic pump drive unit and are designed for ease of installation and maintenance.

The system can be interfaced to any access control systems and a traffic light system is included as standard on all automatic bollard systems.