Sharjah, United Arab Emirates
Our Products
Capacity normally ranges from 40 m to 50 m capacity. Advanced design and features ensures quality of the product. It has thick rock-wool insulation and GI cladding that keeps temperature levels as required. High quality burner and gauge systems keep the temperature constant.
Reciprocating gas compressors
The reciprocating compressors create a low-pressure area in the compression chamber when the piston moves from the highest point to the lowest point of the stroke. Gaseous product (at a higher pressure) moves into the compression chamber. This volume of gas is then displaced when the piston moves to the top of the stroke. Equipped with high-efficiency valves, ductile iron cylinders, self-adjusting piston rod seals and other robust features, these compressors are designed to provide maximum performance and reliability under the most severe service conditions.
Rotary vane compressors
These compressors incorporate simple, dependable, rotating sliding-vane technology to provide sustained performance pressures or vacuums for off-loading liquids. A rotary vane compressor takes in atmospheric air through a high-performance inlet air filter, and discharges the compressed air at a higher pressure into a cargo tank. The elevated pressure pushes the liquid out through the discharge piping.
Screw compressors
Within the compressor body there are two screws with matting profile: a female and a male screw, the female having concave inlets, and the male with convex helical inlets. The screws rotate in opposite directions, with the female screw receiving the driving power and transmitting this power to the male screw through a set of synchronisation gears.
As the screws rotate, the air is drawn into the inlet port and fills up the space between the screws. This phase is theadmission. The key phase is thecompression. It starts when the end of a male thread blocks the end of a female thread. The volume available between the compressor body and these two threads then progressively decreases during rotation. When this volume merges into the delivery outlet of the compressor, the third phase takes place: theexhaust.
Throughout this process, there is no contact between the screws. This means no wear, total reliability, and non-pulsating air delivery. These compressor/blowers can be used in either a mobile or stationary application, and can be driven by a PTO, electric motor, or hydraulic power system. A complete range of dedicated ancillary products is available to support this product line.
Blackmer
Blackmer was incorporated in 1903 and is the leading manufacturer of positive displacement pumps, centrifugal pumps and compressors for the transfer of liquid and gas products worldwide. Positive displacement pump technologies include sliding vane, eccentric disc and peristaltic hose.
The sliding-vane pump and centrifugal pump lines are characterised by proven life-cycle cost features. The compressor technologies include reciprocating, rotary vane, and screw.
Through a global network of distributors and original equipment manufacturers base channels, Blackmer serves the following markets: refined fuels, pulp and paper, oilfield, wastewater, food/sanitary, military/marine, transport and chemical process.
Blackmer Pumps
Sliding-vane pumps: These pumps have a number of vanes that are free to slide into or out of slots in the pump rotor. When the pump driver turns the rotor, centrifugal force, rods, and/or pressurised fluid cause the vanes to move outward in their slots and bear against the inner bore of the pump casing, forming pumping chambers. As the rotor revolves, fluid flows into the area between the vanes (pumping chambers) when they pass the suction port. This fluid is transported around the pump casing until the discharge port is reached. At this point the fluid is squeezed out into the discharge piping.
Eccentric-movement pumps: These pumps consist of a cylinder and a pumping element mounted on an eccentric shaft. As the eccentric shaft is rotated, the pumping element forms chambers within the cylinder, which increase in size at the intake port, drawing fluid into the pumping chamber. The fluid is transported to the discharge port, where the pumping chamber size is decreased. This action squeezes the fluid out into the discharge piping.
Cargo bodies have a basic body design that allows easy loading/unloading of various cargoes. Our cargo bodies can be supplied with or without a chassis-mounted crane to handle loading/unloading with ease.
Chemical tankers are designed and fabricated to perfection and are specially coated inside for chemical product transfer.
Flatbed trailers come with two or three axles depending on the mode of operations. The basic design ensures standard features.
Frac tankers are suitable for transferring large amounts of acidic products such as HCl, H2SO4, etc. High-quality testing procedures ensure the quality and reliability of the various piping and valve operations.
Our fuel tanker trailers are well-fabricated to customer specifications, and to local standards and regulations. ACORN offers fuel trailers for ADNOC distribution for transfer of diesel/petrol fuel. They come with modern safety features such as EBS, Scully overfill systems, etc. The trailers are equipped with all standard accessories to ensure optimum performance.
5000 IG
Thickness6 mm
MaterialASTM A36 / Eqvt.
Manhole450 mm manhole with cover (MMS- Labanon)
PaintInterior: Sand blasted SA 2.5 and diesel-washedExterior: Sand blasted SA 2.5 and single coat with epoxy primer, synthetic finish, enamel coat.
NOTEAcorn reserves the right to alter or modify the construction or material specification or approved drawing as a result of technical progress/improvements/availability.
ACORN low-bed trailers are well designed, are capable of handling higher loads with ease, and come with STD features. ACORNs low-bed trailers are equipped with hydraulically operated automatic ramps.
Screw compressors Bare Shaft
Performance:
Options and Accessories:
Refuse compactors are well-designed with various adapted technological features that offer fully hydraulically operated highly reliable refuse compactors which offer easy trash handling. The hydraulic operations are less complicated and allow optimised trash collection and dumping.
Skeleton trailers range from 25 T to 40 T capacity. ACORNs container carriers are well made to carry single or double containers as per customer requirements, and also come with EBS features.
Tipper bodies are well designed and fabricated from a high-strength mild steel structure, precisely welded and grit-blasted to specific standards in order to achieve higher strength and durability for handling various land solids. The hydraulic systems used allow a higher tipping range in short span of time, and are well known for their reliability.
Well designed for handling sewage waste, and equipped with powerful motor and vacuum systems; with a capacity to carry 6, 000 IG to 10, 000 IG, and with all the safety features.
Water tanker trailers are precisely designed and fabricated as per standard requirements. Trailers are specially coated internally for carrying water.
