Akbar Traders Llc.

Dubai, United Arab Emirates

• LIGHT SALVAGE
• OBJECT RECOVERY
• UNDERWATER CONSTRUCTION
• SCIENTIFIC RESEARCH

• FRACTION OF THE COST OF A BARGE OR CRANE
• EASY FOR A SINGLE DIVER TO USE
• ESPECIALLY SUITED FOR REMOTE LOCATIONS
• DEPLOYABLE FROM SMALL CRAFT

• PROPRIETARY SUBSALVE USA PLUNGER DUMP VALVE ALLOWS AIR CONTROL WITH A PUSH OF A BUTTON AT THE TOP OF THE BAG AND A LANYARD AT THE BOTTOM-VENT AIR FROM ABOVE, BESIDE, OR BELOW THE LIFTING BAG TO ACHIEVE DESIRED ASCENT RATE.
• 1/4" NPT INFLATION PORT FOR REMOTE FILLING, MULTIPLE BAG MANIFOLDING, OR TO INSTALL OPTIONAL STAINLESS STEEL QUICK DISCONNECT.
• READY FOR IMMEDIATE USE-FACTORY-EQUIPPED WITH ALL NECESSARY HARDWARE
• Fabric
  • URETHANE-COATED NYLON-HIGH-STRENGTH AND HEAVY-DUTY
  • SUPERIOR ABRASION RESISTANCE
  • RESISTANT TO MOST PETRO-CHEMICALS
  • UV-RESISTANT
  • LOW MAINTENANCE REQUIREMENTS AND EASY TO CLEAN
  • RF WELDED SEAMS
  Lift Straps Designed for Safety
• EACH SUBSALVE USA LIFT BAG IS TESTED PRIOR TO SHIPPING.
• CUSTOM SIZES AVAILABLE.
• ALL SUBSALVE USA PRODUCTS ARE COMPLIANT WITH IMCA D-016-AIRBAGS, ABS, U.S. DEPARTMENT OF DEFENSE STANDARDS.

• VERSATILE AND EASY-TO-USE, THESE ENCLOSED-BOTTOM, PARACHUTE-SHAPED LIFT BAGS WITH A SINGLE ATTACHMENT POINT ARE ESSENTIAL IN CONSTRUCTION, HEAVY AND LIGHT SALVAGE AND MANY OFFSHORE TASKS.
• "INVERTED WATER DROPLET" DESIGN FACILITATES MAXIMUM LIFT CAPACITY WITH LEAST POSSIBLE WEIGHT, WITH STRESS DISTRIBUTED EVENLY OVER THE FABRIC SURFACE.
• ABLE TO BE PRE-INFLATED WHEN NECESSARY
• WILL NOT DUMP AIR IF THE BAG BREAKS THE SURFACE OF THE WATER
• PRESSURE RELIEF VALVES AT THE BOTTOM OF THE BAG AVOID OVER PRESSURIZATION OF THE LIFT BAG
• EQUIPPED WITH ALL THE NECESSARY HARDWARE AND READY FOR IMMEDIATE USE.

• URETHANE-COATED NYLON-HIGH-STRENGTH AND HEAVY-DUTY
• SUPERIOR ABRASION RESISTANCE
• RESISTANT TO MOST PETRO-CHEMICALS
• UV-RESISTANT
• LOW MAINTENANCE REQUIREMENTS AND EASY TO CLEAN
• RF WELDED SEAMS

• -MULTIPLE NYLON LIFT STRAPS SEWN DIRECTLY TO BOTTOM OF LIFT BAG, WHICH BEARS LOAD AND PROVIDES SAFE WORKING RATIO OF 6:1. - FITTED WITH A 3/4" NPT INFLATION PORT WITH QUICK DISCONNECT OR CAM LOCK FITTING AND A 3/4" STAINLESS STEEL BALL VALVE FOR RAPID DEFLATION.
• 2 TONS AND OVER - DESIGNED WITH A REPLACEABLE HEAVY-DUTY NYLON WEBBING LIFT HARNESS FABRICATED INTO THE SKIN OF THE BAG, WHICH BEARS THE LOAD AND PROVIDES A SAFE WORKING RATIO OF 6:1. - FITTED WITH A 3/4" NPT INFLATION PORT WITH QUICK DISCONNECT OR CAM LOCK FITTING AND A 3/4? STAINLESS STEEL BALL VALVE FOR RAPID DEFLATION.
• • EACH SUBSALVE USA LIFT BAG IS TESTED PRIOR TO SHIPPING.
  • CUSTOM SIZES AVAILABLE.
  • ALL SUBSALVE USA PRODUCTS ARE COMPLIANT WITH IMCA D-016-AIRBAGS, ABS, U.S. DEPARTMENT OF DEFENSE STANDARDS.

When you need to float an object close to the surface, use SUBSALVE's "pillow" shaped Enclosed Flotation Bags in any position-upright or flat, outside or inside of structures-for vessel salvage, auto recovery, pipeline and cable installation and emergency flotation for ships, aircraft, submersibles and ROVs.

• CONFIGURE A MULTITUDE OF RIGGING COMBINATIONS.
• USE WITH A SINGLE PICK POINT (SHACKLE SUPPLIED ON THE BOTTOM OF THE BAG).
• INVERT TO USE THE MULTIPLE STAINLESS STEEL RINGS ON THE TOP OF THE BAG.

• URETHANE-COATED NYLON-HIGH-STRENGTH AND HEAVY-DUTY
• SUPERIOR ABRASION RESISTANCE
• RESISTANT TO MOST PETRO-CHEMICALS
• UV-RESISTANT
• LOW MAINTENANCE REQUIREMENTS AND EASY TO CLEAN
• RF WELDED SEAMS

• HEAVY NYLON LIFT HARNESS BUILT INTO THE BODY OF THE LIFT BAG
• SAFE WORKING RATIO OF 6:1

• EQUIPPED WITH ALL NECESSARY HARDWARE-READY FOR IMMEDIATE USE
• 3/4" NPT INFLATION/DEFLATION PORT EQUIPPED WITH BALL VALVE
• STAINLESS STEEL QUICK DISCONNECT FOR INFLATION
• PRESSURE RELIEF VALVES: SET TO RELEASE AT 2.5 PSI ABOVE AMBIENT PRESSURE
• ENOUGH PRESSURE RELIEF VALES ARE INSTALLED IN EACH BAG TO ALLOW EXPANDING TO VENT SHOULD A FREE ASCENT OCCUR.

Tech divers, wreck divers and public safety divers use this multi-purpose bag as:

• A LIFT BAG TO RECOVER OBJECTS.
• AN UP-LINE FLOAT.
• A DECOMPRESSION-LINE FLOAT.
• A DRY BAG.
• AN INFLATABLE DIVE FLAG/FLOAT TO WARN OFF BOATERS.

Quad bags are ready to go

• MANUFACTURED OF HIGH-STRENGTH, LIGHTWEIGHT, VINYL COATED NYLON FABRIC.
• CAN BE ROLLED UP SMALL ENOUGH TO CARRY ON EVERY DIVE.
• SCREENED ON BOTH SIDES WITH A BRIGHT RED "DIVERS DOWN" FLAG FOR HIGH VISIBILITY
• EQUIPPED WITH AN ORAL INFLATION AND AN OPTIONAL LANYARD OPERATED DUMP VALVE.
• EQUIPPED WITH
• VELCRO TIE STRAP
• BOTTOM WATERPROOF CLOSURE
• STAINLESS STEEL SNAP
• ORAL INFLATION
• EQUIPPED WITH ALL NECESSARY HARDWARE READY FOR IMMEDIATE USE.
• U.S. PATENT NO. D-362, 817

Prop bag

• SPECIALLY DESIGNED LIFT BAGS USED TO REMOVE AND INSTALL BOAT PROPELLERS.
• AVAILABLE IN THREE STANDARD SIZES (100LB, 200LB, 300LB), CUSTOM SIZES AVAILABLE.
• EACH LIFT BAG HAS 4 LIFT POINTS AND ONE DUMP VALVE WITH LANYARD FOR MANUAL OPERATION.

The Subsalve USA lifeboat davit testing system allows for lifeboat davits and other structures to be load tested in areas with insufficient access for conventional solid weights. The handling weight of water filled test bags compared to solid weights is substantially reduced increasing ease of use. To use the system simply place the empty bag in the desired location, fill with water, execute the load test and discharge the water from the bag.

• DESIRED NUMBER OF 375KG CAPACITY TEST BAGS (6 HANDLING STRAPS PER BAG)
• 3/4" X 50FT INFLATION A & DISCHARGE HOSES WITH QUICK COUPLERS FITTINGS
• 6 STATION MANIFOLD WITH 3/4" QUICK COUPLERS
• AIR DRIVEN DOUBLE DIAPHRAGM PUMP RATED TO 15 GPM.
• 25FT INFLATION & DISCHARGE HOSES