Emirates international Equipment & Machinery Est.

dubai, United Arab Emirates

Aquafos Pressure tank

To work with clean water in domestic applications, irrigation, and hydropneumatic sets.

• Pump body and impellers in stainless steel AISI 304.
• Motor shaft in stainless steel AISI 420.
• Suction and discharge mountings in brass.
• Mechanical seal in graphite and alumine.
• Motor housing in aluminium.
• Built-in self priming valve, not very sensitive to the impurities.
• O-rings in EPDM and NBR.

• Asynchronous, two poles
• Class F insulation.
• Continuous operation
• Single-phase with built-in thermal protection.

• Recycling and filtering of water from small and medium swimming pools.

• Pump body, pump foot, impeller, seal mounting and diffuser in technopolymer.
• Motor shaft in stainless steel AISI 420.
• Mechanical seal in graphite and alumine.
• Motor housing in aluminium.
• O-rings in NBR.

• Asynchronous, two poles.
• IP 55 protection.
• Class F insulation.
• Continuous operation.
• Single-phase version built-in thermal protection.

• Maximum suction lift 4 m.

• Supplied with suction and discharge unions (metric or imperial).

To work with clean water. Irrigation and hydropneumatic sets.

• Pump body in stainless steel AISI 304.
• Motor shaft in stainless steel AISI 420.
• Diffusers in glass loaded Noryl.
• Mechanical seal in graphite and steatite.
• Motor housing in aluminium L-2521.
• Windings impregnated with epoxy resin.
• Delta 505/755/1005:Impeller in glass loaded Noryl.
• Delta 1755:Impeller in stainless steel AISI 304.

• Asynchronous, two poles.
• IP 44 protection.
• Class F insulation.
• Continuous operation.
• Single-phase version with built-in thermal protection.
• Provided with removable handle for transport.

• Maximum suction lift: 9m.
• Maximum temperature of liquid: 40C.

• Centrifugal, monoblock and single-impeller electrical pumps with pump body, with connection to the motor by means of a support unit.
• These machines are ideal for pumping clean water and other chemically and mechanically non-aggressive liquids.
• These system can be installed in any position, provided the inlet opening faces upwards, and, thanks to their special design - which allows back pull out of the motor and the rotary parts of the pump and subsequent re-assembly without having to remove the pump body and the pipes connected to it - can be easily and conveniently used for a wide variety of applications in civil, agricultural, industrial or general plant uses.
• Water supply, spray or flowing irrigation, autoclave feed, high pressure system, heating, conditioning and any other general service requiring transfer of clean liquids.

• Max. working pressure 10 bar
• Total suction lift upt o 7 mt.
• Continuous duty.

• Two-Pole induction motor (n = 2850 min-1).
• Insulation Class F.

• Pump body : Cast Iron with flanged inlet and delivery openings and threaded counter-flanges.
• Motor Support: Cast Iron.
• Impeller : Cast Iron.
• Shaft with rotor Stainless Steel.
• Mechanical seal Ceramic/Graphite.

The flat switch EHZ-FS-E is used to control flid levels in tanks, wells or else. It is resistant to water (sewage water) and resists a wide range of oils, most acids and alkalis. Check the compatibility list for more detail. EHZ-FS-C is the version with crossover contacts.

• Microswitch: 250V 400 V 10(8)A 10(4)A
• Switch lifetime: min. 50000 cyclesVDE certifid
• protection: IP 68
• Max. temperature: 60 C
• Working pressure: max. 0.1 bar.
• Contact rating: direct 1 KW at 250 V
• Casing: Polypropylene-Copolymerisate
• Cable: H07RN8F 3G1, 750V, 90C , fie wire, EU certifid for extended submersion in water, H07RN8F 3x1 for FS-C type
• Cable: H07RN8F 3G1, 750V, 90C , fie wire, EU certifid for extended submersion in water, H07RN8F 3x1 for FS-C type
• Dimensions: 156 x 88 x 42 mm (L x W x H)

• Adjustable
• Easy to install
• Reliable
• Maintenance free

Volumetric water pumps able to offer high pressions in relation to comparatively low powers and which have particularly steady operating curves. They are qualified in domestic fittings, to increase the system pressure in aqueducts and for automatic water distribution by small autoclave tanks or by hydrosphere units. For the correct functioning of the pump, use clean water, or non-agressive liquids only, without sand or other solid impurities.

• Max. working pressure 6 bar.
• Total suction lift upt o 8 mt.
• Continuous duty.

• Two-Pole induction motor (n = 2850 min-1).
• Insulation Class F.

• Pump body : Cast Iron
• Motor Support: Aluminium.
• Impeller : Noryl.
• Diffuser: Noryl.
• Pump flange: Stainless Steel.
• Shaft with rotor Stainless Steel.
• Mechanical seal Ceramic/Graphite.

• Selfpriming Twin impeller centrifugal water pumps for suction up to 8 mt. Suitable for civil and industrial purposes and to drain clean and soda water and non-aggressive liquid.

• Total suction lift upt o 8 mt.
• Continuous duty.

• Two-Pole induction motor (n = 2850 min-1).
• Insulation Class F.

• Pump body : Cast Iron.
• Motor Support: Cast Iron.
• Impeller : Noryl Or Bronze(BR).
• Diffuser: Noryl.
• Shaft with rotor Stainless Steel.
• Mechanical seal Ceramic/Graphite.

The most efficient system for adjusting a pumps hydraulic performance to the pressure and flow requirements of supplying water is through the use of variable-speed technology. In the case of supplying water to a building that requires a constant pressure regardless of the water flow requested, with a variable-speed system, in addition to improved efficiency, a high-quality, oscillation-free service is obtained, guaranteeing greater durability of the equipment and the installation.

The ESD unit receives a proportional signal from a pressure transducer fitted on the discharge pipeline. The ESD processes this signal and regulates the motor speed in order to keep the pressure constant at the established level, regardless of the variations in flow demand.

With this pump set the pumps operation can be adapted to the different flow demands, constantly setting the consumption that is strictly necessary for the demand at any given moment. The energy consumption will be proportional to the water consumption. In comparison to the same system running at a fixed speed, this translates directly into energy savings.

The ESD has a backlit display and a 5-button keypad for displaying the user parameters. The installer can easily regulate and modify the basic operational parameters through the same interface. It also includes a reset option to recover the default factory parameters.

• Language: options ES, EN, DE, IT, FR.
• Operation: AUTOMATIC MANUAL
• Set pressure: set point.
• Differential pressure: hysteresis or difference in the set pressure that marks the start-up of the pump.
• Maximum motor intensity: to regulate motor protection.
• Pump sleep frequency: sleep frequency; this can be set manually or automatically.

ESD has a system for automatically calculating the pumps sleep frequency on the basis of the specific characteristics of each installation and the set pressure point.

• Pump stop temporisation
• Nominal motor frequency: 50 Hz 60 Hz.
• Motor rotation reversal
• ONOFF auxiliary pump: auxiliary pump in fixed-speed DOL operation.
• Auxiliary pump in variable speed mode by ESD at variable speed.

• Activation frequency: activation frequency of auxiliary pumps.
• Auxiliary pump activation temporisation.
• Auxiliary pump maximum intensity.

• Set pressure
• Differential pressure.
• Maximum motor intensity
• Stoppage frequency
• Pump stop temporisation.
• Module temperature.
• Alarm display: power surge, short-circuit, power failure and module temperature.
• Operational register: number of start-ups, hours in operation and hours online.

• Selfpriming monoblock water pumps with open impeller.The check valve inside the suction outlet avoids the syphon effect when stopping and assures the automatic re-start each time. The pump selfprimes even if partially filled and if the suction hose is completely empty. Suitable to drain clean or slightly dirty water and in flood irrigation systems.

• Max working pressure 10 bar.
• Total suction lift up to 7 mt.
• Continuous duty.

• Electric standard motor(n = 2900 min-1).
• Insulation Class F.

• Pump body: Cast Iron.
• Motor Support: Cast Iron.
• Impeller Cast Iron.
• Shaft with motor Stainless Steel.
• Mechanical seal Ceramic/Graphite.

• Centrifugal single impeller low head water pumps for flow irrigation systems with high flow rates.
• Suitable to pump clean water or non-aggressive liquids charged with small solid impurities.
• To be used in flow irrigation systems in gardening and agriculture and in industrial fittings.

• Max. working pressure 6 bar.
• Total suction lift upt o 7 mt.
• Continuous duty.

• Two-Pole induction motor (n = 2850 min-1).
• Insulation Class F.

• Pump body : Cast Iron.
• Motor Support: Cast Iron.
• Impeller : Cast Iron.
• Shaft with rotor Stainless Steel.
• Mechanical seal Ceramic/Graphite.

Horizontal, multicellular centrifugal pumps in the DHI range offer the following advantages: High hydraulic pressure and flow rate performance Minimum electrical energy consumption. Extremely quiet operation.

• Transfer of aggressive liquids
• Pumping and distribution of water in domestic appliances used on a continuous or intermittent basis
• Booster system
• For washing and irrigation system gardens and fountains

• Type of liquid: clean water free of suspended solids or abrasive material.
• Maximum liquid temperature 90C.
• Maximum ambient temperature 50C.
• Maximum recommended suction height: 6 m with foot valve (with max liquid temperature at 50 C).
• Maximum operating temperature:
• 10 bar (with liquid temp. 50C)
• 6 bar (with liquid temp. 90C)

• Asyncronous Motor
• Enclosed, externally ventilated.
• Level of protection IP 44.
• Class F insulation.
• Single phase power supply with capacitor permanently activated and thermal protection built into the motor winding.
• Three phase power supply with external protection provided by the user.
• Rotation speed 2850rpm.
• Suitable for continuous use

• The Cutty series comprehend electric pump with plunged impeller, this impeller is multi-pipe, open, with a cutting system in the suction.
• It is particularly suitable in presence of long, filamentous or fibrous fibres, of destroyable solids also of big dimensions and in biologic liquids or in civil waters.

• Submersion depth 20 mt.
• Grain size inlet 50 mm.
• Min. suction level 80 mm.
• Continuous duty.

• Insulation Class F.
• Thermic protection.

• Motor body: Cast Iron.
• Pump body: Cast Iron.
• Impeller Cast Iron.
• Shaft with rotor Stainless Steel.
• Suction strainer Stainless Steel.
• Double mechanical seal Silicon/Silicon + Ceramic/Graphite.

Automatic booster set designed to increase home water pressure. Made up of a single phase DHR pump and of a FLUSSCONTROL electronic control and dry running protection device

• Pumping and distribution of water in domestic systems.
• Booster systems
• Washing systems, irrigation

• Type of liquid: clean water with no suspended solids or abrasive material
• Maximum operating pressure: 10 bar.
• Maximum recommended suction height: 6 m with foot valve.

• Enclosed, externally ventilated.
• Level of protection: IP44.
• Class F insulation.
• Single phase power supply with capacitor permanently activated.
• Thermal protection built into the motor winding
• Speed of rotation 2850 rpm.
• Suitable for continuous use

• Starting pressure (not adjustable): 1, 5 bar
• - Liquid temperature: from 4C to 65C.
• Power supply cable: 1, 5 m.
• H05 RN-F with schuko plug.

Fully automatic variable speed units, for commercial and domestic applications. ESPA In-Line Inverter booster sets are designed to provide an efficient solution to water boosting applications where existing supplies are unreliable or insufficient to meet the demands of commerce and industry. ESPA variable speed booster sets embrace the best in modern control techniques, whilst holding true to the traditional principles of quality engineering. Due to the compact design ESPA booster sets offer a small footprint in relation to performance. Installation is straightforward, with site work usually limited to connecting site pipe work and the provision of a suitable electrical supply.

• Stainless steel suction and discharge manifolds AISI 304.
• Steel chassis finished in black epoxy coating.

An innovative system that can be used with a variation of pump types including multistage and single stage. Saves energy, silent running, compact, and can extend the life of the pump. Designed to vary the frequency (Hz) of the pump in order to keep the hydraulic system at a constant pressure. Interface is user friendly, allowing easy use to calibrate pressure set points, view error messages, and setting. Works directly on the hydraulic manifold and installed on the discharge pipeline of the booster set.

Drainage of sewage and dirty water, operation in septic tanks and small purifying installations.

• Pump body, discharge body, suction body and impeller in cast iron.
• Dilacerative system in steel F-520.
• Mechanical seal in silicon carbide and graphite.
• Pump base in stainless steel AISI 304, detachable for coupling of accessories.
• O-rings in NBR.
• Motor shaft in stainless steel AISI 420.

• Asynchronous, two poles.
• IP 68 protection.
• Class F insulation.
• Continuous operation.
• Water-cooled motor.
• Single-phase version built-in thermal protection and starting box with double capacitor.

• 11/2 BSP female threaded discharge elbow.
• Single-phase supplied with capacitor box.
• Draincor M A:
• complete with float switch

THREE PHASE STARTERS FOR THE CONTROL OF ONE OR TWO DRAINING AND SEWAGE ELECTRIC PUMPS

• IP 54 metallic case.
• General switch.
• Fuse block with fuses for the electric pump.
• Contactor with thermal relay.
• Transformer for auxiliary circuit.
• Fuse block with fuses on the auxiliary circuit.
• Electronic signalling, control and command card equipped with:.
• Function light.
• Power led.
• Thermal block light.
• Electronic keyboard with leds VOLT/ AMPERE.
• Terminal board with level control devices.
• Cable gland.

• Protection level : IP54.
• Power supply voltage : 400V 3F 50 Hz.
• External dimensions : 500 x 750 x 250 mm.

• Manual through general switch.
• Automatic through float switch.

• Environmental temperature : -5 / +40C.
• Relative humidity : 50% at 40C (without forming of condense).
• Standards : EN 60335-1 - EN 60439-1.

• Electronic signalling, control and command card equipped with cyclic startings converter
• For the control of two electric pumps.
• Weight : Kg 15-85

• Electronic signalling, control and command card.
• For the control of one electric pumps.
• Weight : Kg 15-85

• CE040030 - Panel wall mount fixing fins
• UZA00200 - Optical, acoustic alarm
• Float switches (see accessories table)

• Drainage of sewage and dirty water, in domestic installations, operation in septic tanks and small purifying installations.

• Pump body and pump foot in glass- loaded polypropylene.
• Impeller in glass-loaded polyamide.
• Double-lip seal in NBR.

• Asynchronous, two poles.
• IP 68 protection.
• Class F insulation.
• Continuous operation.
• Built-in thermal protection.
• Vigilex M: without floating level switch.
• Vigilex M A**: with floating level switch.

• Maximum passage of solids: 24mm.
• Maximum immersion: 9m.
• Maximum liquid temperature: 40C.

• Supplied with 10m of electrical cable.
• Available with or without float switch.