Emirates international Equipment & Machinery Est.

dubai, United Arab Emirates

Peripheral water pump able to offer high pression in relation to comparatively low power and to have a particularly steady operating curve. Suitable for pouring of non aggressive liquids.

• Selfpriming jet water pumps with a very high hydraulic performance and a considerable pressure capacity.
• Able to pump up to mt. 8 depth and work perfectly even in soda-water.
• Suitable for water lifting and distribution in domestic fittings by small and medium sized tanks.

• Max. working pressure 6 bar.
• Total suction lift upt o 8 mt.
• Continuous duty.

• Two-Pole induction motor (n = 2850 min-1).
• Insulation Class F.

• Pump body : Cast Iron
• Motor Support: Aluminium.
• Impeller : Noryl.
• Diffuser: Noryl.
• Pump flange: Stainless Steel.
• Shaft with rotor Stainless Steel.
• Mechanical seal Ceramic/Graphite.

• Selfpriming water pumps for deep suctions up to mt. 50 to be used in case of important water level gaps.
• Suitable to drain water from wells and in domestic fittings by small and medium sized tanks.
• Before installing the pump verify that all pipes (iron, plastic or rubber) are clean inside so to avoid any obstruction to the ejector nozzle.
• At the foot of the ejector must be installed a foot valve or a check valve. Installed the pump, fill completely both pipes and pump body with clean water.
• To preserve an efficient priming it is necessary a certain pression in the circuit, therefore it is recommended to install a membrane tank at the delivery of the pump.

• Total suction lift upt o 50 mt.
• Continuous duty.

• Two-Pole induction motor (n = 2850 min-1).
• Insulation Class F.

• Pump body : Cast Iron
• Motor Support: Aluminium.
• Impeller : Noryl.
• Diffuser: Noryl.
• Pump flange: Stainless Steel.
• Shaft with rotor Stainless Steel.
• Mechanical seal Ceramic/Graphite.

The DRENOX series pumps are built entirely in AISI 304 stainless steel. Cooling of the motor is via a heat exchange chamber that allows the machine to work for long periods when not completely submerged. Equipped with 32 mm hose adapter. Automatic version equipped with float switch.

• Drainage of seepage water, pumping of rain water, from a grating or drain, pumping of domestic waste water, drainage of environments, bathing and swimming pools, industrial applications.
• Fountains and water features.
• Surface irrigation.

• Type of liquid: partially effluent and dirty clear water, non-aggressive liquids.
• Maximum liquid temperature 40 C.
• Maximum submersion under the water level 7m.
• Minimum drainage level 3 mm for model 80/7, 35 mm for the other models (manual version)
• Free clearance of solids 3 mm for models 80/7, 6 mm for the other models

• Dry motor with stainless steel casing.
• Level of protection IP68.
• Class F insulation.
• Single phase power supply with capacitor permanently activated and thermal protection built into the motor winding.
• Three phase power supply with external protection provided by the user.
• Completely insulated cable connection chamber.
• Self-lubricating ball bearings.
• Speed of rotation 2850 rpm.

Hand-carry submersible stainless steel automatic water pumps. Able to drain infiltrating water, cellars or reservoirs, clean or slightly dirty water and for garden irrigation.

Selfpriming jet inox water pumps with a very high hydraulic performance and a considerable pressure capacity. Able to pump up to mt. 8 depth and work perfectly even in soda-water. Suitable for water lifting and distribution in domestic fittings and little irrigations.

Drainage of infiltration water, empty swimming-pools, operation in decorative fountains and waterfalls.

• Discharge cover, pump casing, motor casing and filter in stainless steel AISI 304.
• Impeller in elastomer plastic, reinforced with steel sheet.
• Pump direction mounting and foot in tecnopolimer.
• Motor shaft in stainless steel AISI 420.
• Mechanical seal in silicon carbide/ alumine oxide.
• O-rings in NBR.

• Asynchronous, two poles.
• IP 68 protection.
• Class F insulation
• Continuous operation.
• Built-in thermal protection.

• Maximum passage of solids: 8mm.
• Maximum immersion: 9m.
• Maximum liquid temperature: 40C.

• Supplied with 10m of electrical cable.
• Integral capacitor.
• Vigila SS: without floating level switch.
• Vigila SS A: with floating level switch.