Lockout Devices #5820454

This cable lockout has been ergonomically designed to fit the hand, making placement and use fast and simple.

Route the cable where necessary to lockout the device then feed the cable down the centre of the open lockout. When the cable is tight and the source is locked out, squeeze the handle closed and apply padlock.

Available in vinyl coated steel and nylon cable versions.

Manufactured from polypropylene, the hexagon design opens up in two halves and is suitable for all kinds of industrial plugs. The small can accommodate 2 padlocks where as the large can accommodate 4. Both lockouts can house padlocks with a shackle diameter of 7mm or less.

Designed to fit on the largest circuit breakers. Turn the circuit breaker into the off position and place the lockout over the toggle switch. Tighten the screw thread to the toggle with the integral pedal sitting into the housing of the breaker to prevent removal.

Fits on top of a variety of push button breakers. This unit traps the button to help prevent it being pushed. Designed primarily as a visual deterrent to prevent accidental reactivation of the circuit.

Designed to encapsulate standard push buttons, this lockout comes with a locking cap to ensure the enclosure cannot be removed without fully removing the padlock.

A universal lockout which is fitted using an internal grub screw.

This version is suitable for larger circuit breakers and can be fitted to toggles 35mm in depth and 40mm wide.

For use on medium sized circuit breakers. Turn the circuit breaker into the off position and place the lockout over the toggle switch. Tighten the screw thread to the toggle with the integral pedal sitting into the housing of the breaker to prevent removal. Maximum toggle width: 20mm

Lockout Electrical Panel Buttons and Switches with no inbuilt lockout provision.

Attach the base plate directly onto the electrical panel. Isolate the unit by placing the house unit over the top preventing access to the switch.

These gate valves are comprised of 2 flattened half moons with a hollow centre. Hinged at one side, they are placed over the valve and then closed, ensuring that the valve wheel is tamperproof. Use a hasp if more than one padlock is required to lockout the device.

Our largest sized gate valve lockout is suitable for valve handles of a diameter from 330mm up to 450mm. It also has an integral clip out centre and a built in facility to use 4 padlocks on the unit without the use of a hasp.

When not in use one side of the lockout can fit within the other to allow for ease of transportation and storage.

2 separate pieces which whilst in place over the valve are slid into each other to enclose the handle.

This design allows it to fit valve handwheels from 25.5mm through to 165mm diameter

When slid into position the wedge on the slider section prevents the compression handle being squeezed, preventing operation of the valve.

Working in a similar way to the standard Ball Valve lockouts, the wedge on the slider section sits between the compression handle and lever, preventing operation.

On flange ball valves the lever handle can be removed after operation. Once the valve is in the desired position and the handle removed, this lockout device fits over the top of the stem ring.

The two sections of the device slide together over the top of the stem, ensuring it is suitable for various sizes of valves. Hole size: 46 x 38mm

The two halves of a Ball Valve Lockout encompasses the ball valve lever along with a padlock and tag to secure it from use.

Filled board contents: 1 x LOK016 5 Padlock Lockout Station 5 x LOK007-L Red Safety Padlocks (KD) 1 x LOK044 25 mm Vinyl Coated Hasp 1 x LOK045 38mm Vinyl Coated Hasp 1 x LOK050 Pk (10) of Do Not Operate Tags

Manufactured from tough moulded polycarbonate this lockout station provides 5 hooks and integral pocket for the presentation of lockout equipment and tags. Complete with hinged translucent cover which protect contents when not in use. Board dimensions (HxWxD): 406 x 315 x 65mm.

Kit contents: 1 x LOK061 Lockout Bag Small (300mm) 2 x LOK0007-L Red safety lockout padlocks (KD) 1 x LOK014 Multi-purpose Cable Lockout with 2.5m nylon cable 1 x LOK045 Vinyl Coated Lockout Hasp 38mm 1 x LOK050 Pack (10) of Do not operate tags 1 x TGPEN01 Ultra-fine permanent pen 1 x LOK006 Adjustable gate valve 1 x LOK023 Small ball valve lockout 1 x LOK043 Universal MCB lockout 1 x LOK063 Pneumatic lockout

Kit contents: 1 x LOK062 400mm lockout bag 1 x LOK023 Small ball valve lockout 1 x LOK025 Large ball valve lockout 2 x LOK014 Multi-purpose cable lockout 2 x LOK044 25mm Vinyl coated hasp 2 x LOK045 38mm Vinyl coated hasp 6 x LOK007-L Red safety lockout padlocks (KD) 3 x LOK050 Pack (10) of Do not operate tags 2 x TGPEN01 Ultra-fine permanent pen 1 x LOK001 25-63.5mm Gate valve lockout 1 x LOK002 63.5-127mm Gate valve lockout 1 x LOK003 127-165mm Gate valve lockout 1 x 4707 Caution Lockout in operation A-Board 1 x LOK030 Large plug / Pneumatic lockout 1 x LOK205 MCB Lockout Pin Out Standard 1 x LOK206 MCB Lockout Pin In Standard 1 x LOK208 MCB Lockout Pin Out Wide 2 x LOK043 Universal MCB lockout 1 x LOK063 Pneumatic lockout 1 x LOK055 3-phase dial lockout

This dual scissor action hasp has a steel body with a powder coating to prevent rusting. The aluminium pivot provides a smooth and lasting movement.

The two different jaw sizes ensure the ultimate in adaptability when lockout conditions vary.

Our premier Di-Electric lockout hasp utilises a unique swing lock system to securely fasten the thread.

Available in 3mm and 6mm thread sizes, each has 4 integral holes for multiple padlock use.