Our Products
DIN 125 WASHER are standard metric washer. A washer is a thin plate disk-shaped with a hole in the middle that is normally used to distribute the load of a threaded fastener, such as a screw or nut. Are also important for preventing galvanic corrosion, particularly by insulating steel screws from aluminum surfaces.
SJS is one of the largest manufacturer of Din 125 Washer established in UAE since 1992. We follow the manufacturing standard of fasteners such as ASTM AISI BS EN ISO DIN & JIS. We are always striving to diversify our Din 125 Washer manufacturing capabilities to be able to satisfy the needs of our customers all around the globe regarding Din 125 Washer.
| DIA OF ROD | ID | OD | THK | |||
|---|---|---|---|---|---|---|
| MIN | MAX | MIN | MAX | MIN | MAX | |
| M8 | 8.40 | 8.62 | 16.00 | 15.57 | 1.80 | 1.40 |
| M10 | 10.50 | 10.77 | 20.00 | 19.48 | 2.20 | 1.80 |
| M12 | 13.00 | 13.27 | 24.00 | 23.48 | 2.70 | 2.30 |
| M14 | 15.00 | 15.27 | 28.00 | 27.48 | 2.70 | 2.30 |
| M16 | 17.00 | 17.27 | 30.00 | 29.48 | 3.30 | 2.70 |
| M18 | 19.00 | 19.33 | 34.00 | 33.38 | 3.30 | 2.70 |
| M20 | 21.00 | 21.33 | 37.00 | 36.38 | 3.30 | 2.70 |
| M22 | 23.00 | 23.33 | 39.00 | 38.38 | 3.30 | 2.70 |
| M24 | 25.00 | 25.33 | 44.00 | 43.38 | 4.30 | 3.70 |
| M26 | 27.00 | 27.33 | 50.00 | 49.38 | 4.30 | 3.70 |
| M27 | 28.00 | 28.33 | 50.00 | 49.38 | 4.30 | 3.70 |
| M28 | 29.00 | 29.33 | 50.00 | 49.38 | 4.30 | 3.70 |
| M30 | 31.00 | 31.39 | 56.00 | 55.26 | 4.30 | 3.70 |
| M32 | 33.00 | 33.62 | 60.00 | 58.80 | 5.60 | 4.40 |
| M33 | 34.00 | 34.62 | 60.00 | 58.80 | 5.60 | 4.40 |
| M35 | 36.00 | 36.62 | 66.00 | 64.80 | 5.60 | 4.40 |
| M36 | 37.00 | 37.62 | 66.00 | 64.80 | 5.60 | 4.40 |
| M38 | 39.00 | 39.62 | 72.00 | 70.80 | 6.60 | 5.40 |
| M39 | 40.00 | 40.62 | 72.00 | 70.80 | 6.60 | 5.40 |
| M40 | 41.00 | 41.62 | 72.00 | 70.80 | 6.60 | 5.40 |
| M42 | 43.00 | 43.62 | 78.00 | 76.80 | 8.00 | 6.00 |
| M45 | 46.00 | 46.62 | 85.00 | 83.60 | 8.00 | 6.00 |
| M48 | 50.00 | 50.62 | 92.00 | 90.60 | 9.00 | 7.00 |
| M50 | 52.00 | 52.74 | 92.00 | 90.60 | 9.00 | 7.00 |
| M52 | 54.00 | 54.74 | 98.00 | 96.60 | 9.00 | 7.00 |
| M55 | 57.00 | 57.74 | 105.00 | 103.60 | 10.00 | 8.00 |
| M56 | 58.00 | 58.74 | 105.00 | 103.60 | 10.00 | 8.00 |
| M58 | 60.00 | 60.74 | 110.00 | 108.60 | 10.00 | 8.00 |
| M60 | 62.00 | 62.74 | 110.00 | 108.60 | 10.00 | 8.00 |
| M64 | 66.00 | 66.74 | 115.00 | 113.60 | 10.00 | 8.00 |
| M68 | 70.00 | 70.74 | 120.00 | 118.60 | 11.00 | 9.00 |
| M72 | 74.00 | 74.74 | 125.00 | 123.40 | 11.00 | 9.00 |
| M76 | 78.00 | 78.74 | 135.00 | 133.40 | 11.00 | 9.00 |
| M80 | 82.00 | 82.87 | 140.00 | 138.40 | 13.20 | 10.80 |
| M85 | 87.00 | 87.87 | 145.00 | 143.40 | 13.20 | 10.80 |
| M90 | 93.00 | 93.87 | 160.00 | 158.40 | 13.20 | 10.80 |
| M95 | 98.00 | 98.87 | 165.00 | 163.40 | 13.20 | 10.80 |
| M100 | 104.00 | 104.87 | 175.00 | 173.40 | 15.20 | 12.80 |
A ring split at one point and bent into a helical shape. This causes the washer to exert a spring force between the fastener's head and the substrate, which maintains the washer hard against the substrate and the bolt thread hard against the nut or substrate thread, creating more friction and resistance to rotation. Spring washers are a left hand helix and allow the thread to be tightened in a right hand direction only, i.e. a clockwise direction. When a left hand turning motion is applied, the raised edge bites into the underside of the bolt or nut and the part that it is bolted to, thus resisting turning. Therefore, spring washers are ineffective on left hand threads and hardened surfaces. Also, they are not to be used in conjunction with a flat washer under the spring washer, as this isolates the spring washer from biting into the component that will resist turning.
SJS is one of the largest manufacturer of Spring Washers established in UAE since 1992. We follow the manufacturing standard of fasteners such as ASTM AISI BS EN ISO DIN & JIS. We are always striving to diversify our Spring Washers manufacturing capabilities to be able to satisfy the needs of our customers all around the globe regarding Spring Washers
| Dia | ID | OD | THK |
|---|---|---|---|
| M5 | 5.10 | 9.20 | 1.20 |
| M6 | 6.10 | 11.80 | 1.60 |
| M8 | 8.10 | 14.80 | 2.00 |
| M10 | 10.20 | 18.10 | 2.20 |
| M12 | 12.20 | 21.10 | 2.50 |
| M14 | 14.20 | 24.10 | 3.00 |
| M16 | 16.20 | 27.40 | 3.50 |
| M18 | 18.20 | 29.40 | 3.50 |
| M20 | 20.20 | 33.60 | 4.00 |
| M22 | 22.50 | 35.90 | 4.00 |
| M24 | 24.50 | 40.00 | 5.00 |
| M27 | 27.50 | 43.00 | 5.00 |
| M30 | 30.50 | 48.20 | 6.00 |
| M36 | 36.50 | 58.20 | 6.00 |
| M39 | 39.50 | 61.20 | 6.00 |
| M42 | 42.50 | 66.20 | 7.00 |
| M45 | 45.50 | 71.20 | 7.00 |
| M48 | 49.00 | 75.00 | 7.00 |
| M52 | 53.00 | 83.00 | 8.00 |
| M56 | 57.00 | 57.00 | 8.00 |
| M60 | 61.00 | 91.00 | 8.00 |
| M64 | 64.00 | 95.00 | 8.00 |
A flat washer with a particularly large outer diameter in proportion to its central hole. These are commonly used to spread the load on thin sheet metal, and are named after their use on automobile fenders. They can also be used to make a connection to a hole that has been enlarged by rust or wear.
SJS is one of the largest manufacturer of Fender Washers established in UAE since 1992. We follow the manufacturing standard of fasteners such as ASTM AISI BS EN ISO DIN & JIS. We are always striving to diversify our Fender Washers manufacturing capabilities to be able to satisfy the needs of our customers all around the globe regarding Fender Washers.
Load Indicating Washer also known as Direct Tension Indicators show that a defined preload is achieved in the bolt. The Load Indicating Washer can be used alone or with bolt face washers or nut face washers conforming to BS EN 14399-9. In either case it is essential that the Load Indicating Washers are used as part of an assembly in accordance with BS EN 14399-1. To comply with BS EN 14399-1, it is essential that the assemblies are supplied by one manufacturer and include bolts, nuts, washers and Load Indicating Washers.
SJS is one of the largest manufacturer of Load Indicating Washer established in UAE since 1992. We follow the manufacturing standard of fasteners such as ASTM AISI BS EN ISO DIN & JIS. We are always striving to diversify our Load Indicating Washer manufacturing capabilities to be able to satisfy the needs of our customers all around the globe regarding Load Indicating Washer.
A type of washer designed to be used underneath nuts with tapered flanges to enable the bolt assembly to fit properly when tightened.
SJS is one of the largest manufacturer of Taper Washers established in UAE since 1992. We follow the manufacturing standard of fasteners such as ASTM AISI BS EN ISO DIN & JIS. We are always striving to diversify our Taper Washers manufacturing capabilities to be able to satisfy the needs of our customers all around the globe regarding Taper Washers.
| Dia | ID | A | B | THK |
|---|---|---|---|---|
| M8 | 9.00 | 22.00 | 22.00 | 3.80 |
| M10 | 11.00 | 22.00 | 22.00 | 3.80 |
| M12 | 13.50 | 26.00 | 30.00 | 4.90 |
| M16 | 17.50 | 32.00 | 36.00 | 5.90 |
| M20 | 22.00 | 40.00 | 44.00 | 7.00 |
| M22 | 24.00 | 44.00 | 50.00 | 8.00 |
| M24 | 26.00 | 56.00 | 56.00 | 8.50 |
Hillside washers are used to evenly distribute load in cross bracing applications. Diagonal tie rods or cable assemblies with welded eye bolts are frequently used to support wall columns and steel beams in metal building construction.
SJS is one of the largest manufacturer of Hillside Washers established in UAE since 1992. We follow the manufacturing standard of fasteners such as ASTM AISI BS EN ISO DIN & JIS. We are always striving to diversify our Hillside Washers manufacturing capabilities to be able to satisfy the needs of our customers all around the globe regarding Hillside Washers.
umm al quwain, United Arab Emirates 