ANBI General Trading L.L.C

Dubai, United Arab Emirates

Water hammeris usually recognized by a banging or thumping in water lines. The noise can occur when the flow of moving water is instantaneously stopped by a closing valve, or there are loose pipes in the wall, or there is a worn out washer on a faucet. The sudden stop of water, or a stutter caused by a loose or bad washer, results in a pressure spike behind the valve which acts like a tiny explosion inside the pipe. This pressure spike will create shock waves in the water that will reverberate throughout the plumbing system, rattling and shaking pipes, especially loose pipes, until it is absorbed.

Normally, a sufficient pocket of air will absorb such a pressure spike, but if no pocket of air is present, expensive fixtures and appliances within the plumbing system will be damaged as they are left to absorb this pressure spike.

Pre-charged copper water hammer arrestor with teflonpiston, EPDM o-ring seal, and brass NPT or BSPT threaded connection.

OPERATING PRESSURE: Designed to operate on all domestic and commercial lines up to 350 psi working pressure.

TEMPERATURE RANGE: 33F to 250F (0.5C to 121C).

Honeywell Refrigerants Gas is the established technical leader in the development of fluorine-based (HFC) refrigerants.

Honeywell Refrigerants Gas is the established technical leaderin the development of fluorine-based (HFC) refrigerants for the commercial and industrial refrigeration industry worldwide. And, as you would expect from a world-class supplier, we have been at the forefront of the industrys drive to develop these safer, non-ozone depleting alternatives to the older technology, environmentally unfriendly CFC and HCFC refrigerants, in compliance with global legislation for their phase-out.

To ensure that customers are fully supported in this transition, Honeywell has dedicated its research resources to developing a comprehensive range of alternative intermediate and long-term refrigerants, that are not only safer to use but that are able to meet or surpass the performance levels of the products they replace.

For commercial and industrial refrigeration replacement of (CFC) Genetron 502 and (HCFC) Genetron 22 are the industrys principle focus. Honeywells long-term solutions for low and medium temperature applications are Genetron 507 and Genetron 404A, both non-ozone depleting refrigerants. Genetron 507 is an azeotropic blend of HFC-125 and HFC-143a, and Genetron 404A is a blend of HFC-125, HFC-143a and HFC 134a. Both options can give a high level of efficiency with performance and characteristics similar to Genetron 502, and be used as replacements in retrofits as well as in new equipment.

Honeywell Refrigerants Gas is a global leader in the development and production of high-performance fluorocarbon refrigerants and thermal working fluids. Our customers include original equipment manufacturers, service technicians and facility managers, and consumers around the world.

The elimination of ozone-depleting refrigerants and chemicals continues to be a key environmental focus for Honeywell as countries phase out these chemicals in accordance with the international agreement Montreal Protocolon Substances that Deplete the Ozone Layer. We have invested in both R&D and manufacturing capacity to help countries and companies meet our commitments to this global effort by moving to non-ozone depleting alternatives.

At Honeywell, we see Responsible Care as the foundation of environmental, health and safety excellence in our business. We incorporate HSE management systems into all phases of the chemical life cycle. Our commitment to continuous health, safety and environmental performance improvement is evident at our facilities around the world it is the way we do business.

Chrome-plated brass. Single lever operation. Suitable for high and low pressure systems.

Timeless and deliberate, the Composed collection embodies the beautifully understated elements of minimalist design. By eliminating unnecessary details, the collection is designed to elicit an emotional response with its stark, refined beauty. This 45Cm (17.71 Inch) towel bar complements composed faucets and accessories.

FEATURESWall MountedPremium metal construction for durability.Mounting Accessories includedChrome FinishCoordinates with faucets and accessories in the Composed collection.

Codes/StandardsNone Applicable

The Makita Blower (model UB1103) is a go-to tool for fast clean upon the jobsite or in the workshop. The Blower is powered by a 6.8 AMP motor with a variable speed control dial and trigger with lock-on for added convenience. With a maximum air speed of 203 MPH and a maximum air volume of 145 CFM, youll get faster clean-ups. The blower can also be used as a vacuum; simply move the nozzle to the vacuum port and connect the dust bag.

• SPEED: Delivers a Maximum Air Speed of 203 MPH for Faster Job Site Clean Up
• PERFORMANCE: Variable speed control dial and trigger (0-16, 000 RPM) for increased performance
• EFFICIENCY: Maximum air volume of 145 cfm for faster clean up in larger areas
• CONVENIENCE: Two tools in one; quickly converts to a vacuum for added versatility
• INCLUDES: Nozzle and dust bag

Keep your drains clean with this set of 10 rod drain cleaners. Easy to use, its a fast DIY alternative to calling your plumber. Its sturdy rods attaches to form one long rod and includes a plunger attachment. This is a handy tool to have in your home for plumbing emergencies.

Canvas is commonly used with mastics or coatings to provide a protective barrier over pipe and duct
insulation. Stocks 6 oz. and 8 oz. varieties of canvas.

Canvas is commonly used with mastics or coatings to provide a protective barrier over pipe and ductinsulation. Stocks 6 oz. and 8 oz. varieties of canvas.Its 100% cotton fabric used for insulation of Galvanized Steel ducting.

6 oz. Canvas Specifications:

• First Quality Material
• 100% cotton greige single filled osnaburg
• Approximately Width -1 YARD (36inch) x Lgth- 20YARD (720inch)
• Thread Count = 36 x 28
• Weight = .51 Lbs/LY

Dielectric Unions features a female steel pipe thread to female brass pipe thread connections. These unions are designed to be installed between pipes made from dissimilar metals to prevent accelerated corrosion and deterioration in the piping system due to galvanic and stray current. It Consists of a union nut, two tailpieces, a gasket & a sleev that separates the tailpieces to prevent an electric current from occurring. This is ideal in applications such as commercial and residential as hot water storage tanks, chilled water, processing tanks, steam, gas and other water piping applications.

max Pressure 250PSI (17.2bar)

max Temp 180DegF

Connection Type FPT Steel Pipe x FPT Brass Pipe

Cast iron body GJL 250 according to EN 1561, flange according to EN 1092, PN 16; length according to NORM EN 558-1, basic series 1, with blue enamel coating. Cover with drain bore and drain plug 1/2. Four bores Rp 1/4 with drain plug for differential pressure measurement. Test points 1 0284 01 and 1 0284 02 have to be ordered separately.

The ANBI collection is designed to be inviting, homely and user-friendly the perfect addition to a modern bathroom.The Hotel seriesrange gives you a simple contemporary design that compliments almost any style. ANBIdesign and manufacture their products using the finest methods and materials to ensure a high quality product.

Dimensions (W)110 x (D)140 x (H)55.75mmMaterial BrassFinish Chrome PlatedProduct Type ContemporaryFrosted Glass Soap DishChrome plated to BS EN 248

Theseend Capfeature carbon steel construction and are suitable for use in HVAC, chemical refineries, fertilizer and petrochemical plants and in gas, oil and water transmission systems.

Multi jet, dry dial, direct reading. Made in the version for cold water (30C) in the diameters 15 to 50 mm (1/22). Risks of corrosion and sedimentation free. Antimagnetic protection upon request. Long durability and elevated precision guaranteed. Approved according to MID standards up to R160H.

The multi-jet water meter is used both in the domestic and the industrial field. The principle of operation is to force the passage of the inlet water flow through a series of ducts open in a capsule, called distributor, containing the turbine. The entrance of the water through the ducts generates a series of symmetrical jets that impact the turbine keeping it in perfect balance.

There are three multi-jet water meter types:Wet dial meters with the reading mechanism completely immersed in the water and direct transmission from the turbine to the gears of the mechanism itself.Semi dry dial meter with the reading mechanism completely immersed in the water and the rollers protected in a sealed capsule. Direct transmission from the turbine to the gears of the reading mechanism.Counter dry dial, with clockwork separated from the flow of water. In this case the transmission gears to watch takes place via magnetic coupling.

AerofoamNBR Rubber Insulation Rolls and Sheetsare closed cell elastomeric foam structures with a non-porous composition that offers high thermal efficiency and protection from imminent condensation problems

AerofoamNBR Rubber Insulation Rolls and Sheetsare closed cell elastomeric foam structures with a non-porous composition that offers high thermal efficiency and protection from imminent condensation problems, and helps as sound absorber. Depending on the requirements of the market, this product can be coated with different types of foils and have a factory-applied self-adhesive backing. The installation time is reduced more than 40% due to the ease in cutting as well as quick adhesion of the material.

AerofoamNBR Rolls and Sheets come in handy where Aerofoam(NBR) Nitrile Tubes cannot be used on pipes with big diameter. Other applications include ventilation ducts, tanks, and reservoirs, engine rooms assound and thermal protection. Not only are they environmentally friendly, they pose no harm to human health, it has zero Ozone Depletion Potential (ODP), Global Warming Potential (GWP) of less than five, and a low Volatile Organic Compound (VOC) of less than 6 g/m2/hr in 24 hours. Aerofoam NBR Rolls and Sheets comply with LEED requirements.

Stainless steel disc with extended test points Maximum working temperature 120C Maximum static pressure 16 bar Kv-values, also pressure and temperature ratings, comply with requirements of BS7350 Kv-values in m3/hour at a pressure drop of 1 bar.

This slip on flange allows you to bolt 2 flanges together with a gasket to form a tight seal that still eases access to the piping system. For use with air, water, oil, natural gas, or steam.

Flange slips over the pipe and is then fillet weldedExcellent for fabricated applications

This weld neck flange allows you to bolt 2 flanges together with a gasket to form a tight seal that still eases access to the piping system. Attaches to system via a circumferential weld at the neck; welded area can be easily examined by radiography. Matched pipe and flange bore reduces turbulence and erosion inside the pipeline.

For use with air, water, oil, natural gas, or steamExcellent in critical applications

Flow Controller with Integrated Control Valve made of cast iron GG 25, flange according to EN 1092-2, PN16. Suitable for controlling the flow rate in cold and hot water systems.

• Max. differential pressure 4 bar.
• Max. diff. pressure accross the restrictor 0.2 bar.
• Temperature range: 5C to 120C
• Gasket material FPM
• Cones WN1.4057, stem WN1.4404
• seat material WN1.4021
• Impulse tupe WN1.4301
• Diaphragm material EPDM.

Commonly used to blank off pipelines, valves, and pumps, or as an inspection cover, this ANBI APPROVED blind flange allows you to bolt 2 flanges together with a gasket to form a tight seal that still eases access to the piping system. This model is sometimes referred to as blanking flange and is for use with air, water, oil, natural gas, or steam.

Features:LOW NOISE0-50 SECONDS DRY TIMEMOUNTING SCREWS INCLUDEDNO NEED FOR TOUCHINGRUST RESISTANT

TheseConc Reducerfeature carbon steel construction and are suitable for use in HVAC, chemical refineries, fertilizer and petrochemical plants and in gas, oil and water transmission systems.

These Conc Reducerfeature carbon steel construction and are suitable for use in HVAC, chemical refineries, fertilizer and petrochemical plants and in gas, oil and water transmission systems.

PVC End Caps are solvent cemented to the end of a pipe by inserting the pipe into the socket of the cap. The caps have a flat end which makes them ideal for fabricators who wish to drill and/or thread small components into them. The caps are designed for pipe of the same size category to be solvent cement welded into them. Our PVC plain end caps have a pressure rating of greater than 10bar and are fully WRAS approved for use with drinking water.

Crayflex 13APM is made of triple lamination of aluminum foil, polyester and metallized polyester film permanently bonded to a coated spring steel wire helix

or HERZ-Flow controller 4001, used from 2009for HERZ-Differential pressure controller 4002, used from 2009for HERZ-Combi Valve 4006for HERZ-Control valve 7217 V.

EAN 90 04174.

Order number Item 02670 61 4006 021

Duct Liner is a highly efficient, semi-rigid insulation of fine, stable and uniformly textured inorganic glass fibers bonded together by a non-water soluble and fire retardant thermosetting

DESCRIPTION

Duct Liner is a highly efficient, semi-rigid insulation of fine, stable and uniformly textured inorganic glass fibers bonded together by a non-water soluble and fire retardant thermosetting and heat resistant resin. It is free from coarse fibers and shot due to its mineral composition.

APPLICATION

Duct Liner is intended for use in commercial, institutional, industrial and residential construction as thermal and acoustical insulation of heating air-conditioning and interior of dual temperature duct work, air handling equipment and plenums operating at air-velocities up to 30 m/s (6000 FPM) and temperatures up to 121C(250F).

Also used as an efficient sound absorption treatment of walls and ceilings, acoustic enclosures, generator rooms, studios, curtain walls, auditoriums, conference rooms, theaters and others.

Semi-rigid and rigid slabs manufactured from stable glass fibres bonded with thermo-setting resins, and free from coarse fibres and shot. Easy to handle and cut to fit rectangular ducts and air handling equipment.

Single lever mono mixer kitchen tap. Chrome-plated brass. Swirl type.

• Single Lever Operation
• Ceramic Disc Valves
• Surface-Mounted with Swivel Spout
• Flow Straightener
• Suitable for High Pressure Systems
• 2 x (nut) x 300mm Flexible Pipes connections
• Deck Mounted Drill hole diameter 34mm
• Minimum Operating Pressure 0.5 BAR LP> Max. temperature hot water connection 80C/176F. Recommended temperature is 65C/149F

SS SERIES pre-charged all stainless steel shock arrestor with stainless steel bellows, and male threaded connection.

Water hammeris usually recognized by a banging or thumping in water lines. The noise can occur when the flow of moving water is instantaneously stopped by a closing valve, or there are loose pipes in the wall, or there is a worn out washer on a faucet. The sudden stop of water, or a stutter caused by a loose or bad washer, results in a pressure spike behind the valve which acts like a tiny explosion inside the pipe. This pressure spike will create shock waves in the water that will reverberate throughout the plumbing system, rattling and shaking pipes, especially loose pipes, until it is absorbed.

Normally, a sufficient pocket of air will absorb such a pressure spike, but if no pocket of air is present, expensive fixtures and appliances within the plumbing system will be damaged as they are left to absorb this pressure spike.OPERATING PRESSURE:Designed to operate on all domestic and commerical lines up to 150psi working pressure, 250psi static pressure.

TEMPERATURE RANGE:-100F to 300F (-73C to 149C)

Application

T6861 digital thermostats are designed for application of 3-speed fan and valves in fan coil system.

Including: 2-pipe cool only/heat only/manual changeover and 4-pipe manual or automatic changeover Ventilation modeManual or automatic 3-speed fan controlWater valve controlFan speed can be selected to automatic or manual 3-speed control mode.In ventilation mode, fan only support manual speed control.

Features

Super modern appearance design, suitable for office, hotel and residential buildingHorizontal and vertical model available for variant applicationSlim design, direct installation on 86 size boxStylish and elegant blue/green back-light with blue/ green color ring2-pipe/4-pipe integrated into one unit with easy configurationBig LCD display with English and iconsEasy to install and set-upTime on/off functionSelectable room temperature or set point displayManual or automatic fan speed selectionRemote temperature sensorEnergy saving mode activation by button press or dry contact (key card)Cycle per Hour (CPH) functionAdjustment of display room temperatureTemperature unit either o C or o FUser setting can be kept when power offFreezing protection function availableLock or unlock keys or part of keys in Installer SetupHeat and cool setpoint limitation for energy saving

Radiator connection with cone. Universal models with special sockets for threaded pipes and compression adapter. Can be used with Thermal Actuators

All models are nickel plated and supplied with a screw cap.

Universal models with threaded socket:1 7723 93 1 Straight model1 7724 93 1 Angle model

Maximum operating pressure 120 CMaximum operating temperature 10 barHeating water purity according to Austrian standard NORM H 5195 and/or VDI-guideline 2035.When using HERZ compression unions for copper and steel pipes, observe the permissible temperatures and pressuresas specified in EN 1254-2:1998 Table 5. A maximum operating temperature of 80 C and maximum operating pressureof 4 bar applies for plastic pipe connections, if permitted by the pipe manufacturer.

Flexible Duct Connectorsis a very strong fully flexible duct connector and is widely used in Air Conditioning Systems for Commercial, Industrial and Residential applications.

Conforming to IS 2993 (for Motors). IS 1709 (for Fans), IS 1569 (for lighting fixture) are manufactured by using Zinc Alloy, Heavy Edge Metalised Polypropylene Film and encapsulated

The Product is formed of three layers:

1. inner soft pvc layer
2. Outer layer made of high transparency UV-resistant modified PVC
3. middle reinforced layer made of evenly-wound high strength polyster

Colour available in Green & Yellow

Application Used for garden irrigation.

Products have passed the test of FDA and ROHS by SGS.

Sizes 1/2, 3/4, 1

Vacuum breaker are specially made to attach with portable hoses, hose threaded bib taps and other faucets. Designed to prevent the flow of contaminated water back into the portable water supply, this device requires no plumbing changes and screws directly onto a bib tap and faucets. It can be used for a wide variety of installations, such as service sinks, swimming pools, photo developing tanks, laundry tubs, wash racks, dairy barns, marines and general outside gardening uses.

These 90Deg elbows feature carbon steel construction and are suitable for use in HVAC, chemical refineries, fertilizer and petrochemical plants and in gas, oil and water transmission systems.

Key Features:The H801 protection: filters at least 95% of solid and liquid aerosols that do not contain oil.The nose clip is metallic which is easy to shape around the nose.Twin, latex-free, straps are elasticated fabric, fully welded to the mask. These are sweat absorbent and provide an excellent degree of tightness.High performing, humidity-resistant & low breathing resistance filter mediaLightweight design to reduce wearers fatigueEasy to wear with safety spectacles, goggles, giving an excellent field of vision: comfort and versatility means greater efficiency on the job.The shell incorporates and arc shaped ribbing for anti deformation.Existing with high performance exhalation valve to breathe out easily

Industry:Agriculture Chemical Industries Fire Protection brigades Food Industries Medical and Pharmaceutical Transportation Welding

Suitable for domestic water services, heating and air-conditioning plants, compressed air systems.Female/female threads and inspection plug.Body in brass.Minimum and maximum working temperatures: -20C, 110C in absence of steam.Filtration degree: 1/2 through 2 750m;Threads: ISO228 (equivalent to DIN EN ISO 228 and BS EN ISO 228).

An ideal pack to repair or refurbish a WC / toilet cistern with a top flush cistern cover or in a furniture unit where the push button is on the counter top. Bring old tired cisterns back to life and working like new. The fill valve is adjustable in height allowing installation in a range of different height cisterns.

Dual flush valve allows for full or half flush

Features:

> Convert your existing toilet to Dual Flush Technology> Uses up to 45% less water> Fully adjustable full and half flush, Button included> Retrofits any 2 flush valve toilet> Includes high performance fill valve 2x greater refill rate

> Fits all ceramic cistern adjustable height> Wide Hydraulic closure pressure range 0.1-10bar> Top Silent 12-13db(A) far exceeds sound Class1 requirements 20db> Dual Flush water saving technology standard> Faster Installation No need to measure the cistern height

Contents:> Bottom Inlet with 3/8 Brass> Dual flush valve for 2Piece toilet (Overflow pipe not adjustable)> Dual Push Button> 3/8 Inlet Valve refill blocked Plug> Iron coated connecting bolts (M6x85mm)> Bowl Gasket

DEXPURE 45800-21 Disposable Latex Powdered GlovesLatex Powedered Gloves0.08mm thick 250mm

Application:Agrifood Industry Fish, Meat and Poultry, Dairy products, Pastry, Laboratory Analysis and Technical work, Pharmaceutical product preparation, Product inspection, Electronic assembly

Industry:Automotive and Part Manufacturing Aviation -Catering Chemical Industries: Food Industries- Industrial Cleaning Laboratory Maintenance Medical and Pharmaceutical Petrochemical Printing Industries Water treatment

Size: L

FeatureNatural latex powdered gloveSingle use

BenefitCOMFORTDisposable glove for an excellent touch.Smooth finish to give a good dexterity. The powdered interior facilitates putting the glove on and taking it off.

SAFETYThe glove is made from pure natural latex.Regular controls ensure a very low residual protein rate.

HYGIENEThe glove is treated to prevent the development of bacteria.Certified for contact with food.

ANBI BATH MIXER Brass Wall Mounted Angel Series

Our ANBI Bath ShowerMixer Taps are the perfect solution for updating your bathroom in a simple andeasy way. If you are limited in space these taps are perfect for shower andbath enclosures. Go traditional with the ANBI shower bath mixer tap or more modern with the innovative Open Water mixer tap. Stylish, functional andaffordable.

Features and benefits

• Diverter handle addsto the lavishness
• Only 0.2 bar pressure required to provide a great flow
• Brass body and Chrome plating so it wont rust
• Because it usestraditional spindle cartridges, the flow is great even on a low-pressure watersystem (min 0.2 bar), and has also been fully tested to work perfectly onpressure up to and including 5.0 bar.
• Manufactured from VirginBrass so it wont rust and dipped in chrome for a perfect finish.
• Co-ordinates perfectlywith the rest of the ANBI tap range.

Whats included

1 x Bath shower mixer1 x Fixed shower bracket

The ANBI collection is designed to be inviting, homely and user-friendly the perfect addition to a modern bathroom.

The ANBI collection is designed to be inviting, homely and user-friendly the perfect addition to a modern bathroom.

If youre looking for bathroom accessories with extra style, ANBI would be the perfect choice. ANBI design and scope of choice bring easy and coordinated harmony to any bathroom.

Model Number: ABHOT-8127-SSFinish: ChromeMaterial: Brass & Frosted GlassSize: 600mm (L) x 127mm (Projection) x 53mm (H)