Post Buy Requirement
DF

Daly Fluid Technologies (L.L.C.)
DubaiUnited Arab Emirates

Add Review

Our Products

  1. Flow Meters 10 Products available
  2. Transmitter Device 4 Products available
  3. Sensors And Transducers 4 Products available
  4. Industrial Valves 4 Products available
  5. Valves & Valve Fittings 3 Products available
  6. Flush Bottom Outlet Valve 3 Products available
  7. Domestic Luminaires 3 Products available
  8. Pressure Switches 3 Products available
  9. Process Control Systems & Equipment

    2 Products available
  10. Electronic Test Instruments

    2 Products available
  11. Others Products 87 Products available

Other Products / Services

Our Complete range of products are Lumin EX LED Worklight, PNEL ATEX Extension Lead, ATEX Blast Light, PNER ATEX Extension Reel and PNSB ATEX Splitter Box.

Torches & Handlamps

Weighing just 145g, the SA LUMIN Rechargeable EX LED Torch packs the power of a much larger handlamp into a compact, robust package. It throws out an impressive 135 lumens where you need it, and an Intelligent Light Sensor adjusts the beam, extending battery life to save you time and money. Running up to 30 hours on one set of four standard AAA batteries, it also features a glo cap so it's easy to find in the dark.

Specifications:
  • ATEX Certified for Zones 0, 1 and 2 (gas), 20, 21 and 22 (dust)
  • Penetrating light beam
  • Waterproof and dustproof
  • Ergonomic design
  • Optimum light output to size ratio
  • Intelligent Light Sensor
  • Emergency Function
  • Up to 30 hours battery life
  • Uses standard AAA batteries
  • Glo cap
  • Can also be configured with a 5 piece charging rack
View Complete Details

Bulkhead Lighting Exit Sign

Description

Specifically designed for hazardous environments which require high performance, high reliability, White-Light illumination. ATEX and IEC Ex approved for all Zone 1 and Zone 2 applications, rated for T4 and T5 environments. Low profile design, allows easy access to the back of the unit with rear cable entries, cabling can be hidden and protected from damage. Housed in marine grade aluminium, IP66 and IP67 rated for extreme environments. Also available as an emergency fitting with integral battery back-up.

Specifications:
  • IP66 & IP67
  • Temperature range: -50C to +46C (-20C emergency variants)
  • Weight: 5kg (11.0lbs) Standard, 6kg (13.2lbs) Emergency
  • Dimensions: 288 x 220 x 122mm (11.3 x 8.7 x 4.8 inch)
  • 110-254V 50/60Hz AC only
  • Power: 34W standard, 37W emergency
  • Termination: Incoming terminal block suitable for looping 4 core 4mm cable
  • Power Factor >0.95
View Complete Details

LED Rechargeable Floodlight

The powerful SA LUMIN LED Rechargeable Floodlight is lightweight, fully portable has a 12 hour battery to cover a full shift and completely eliminates trip hazards from trailing cables. THE SARF300 provides up to 2000 lumens of light output and includes a 'blink' and ultra lower power mode when you reach your last 30 minutes of battery to ensure you don't suddenly experience a loss of light and can exit the tank safely. Using no trailing cables vastly reduces trip hazards, while the powerful light output easily illuminates the working environment. The unit is ergonomically designed for easy manoeuvrability, it is extremely user friendly and has a wide range of accessories available such as magnetic mounts, scaffold brackets, blast screens and more.

The SARF300 is fully certified for Zones 1 & 2 (Gas) and Zones 21 & 22 (Dust) and carries a worldwide 5 year warranty.

Specifications:
  • ATEX and IECEx Certified for Zones 1 and 2 (gas), 21 and 22 (dust)
  • Certified Portable
  • High Power LED Light Beam
  • 5 year warranty
  • High/Medium/Low Battery Indicator
  • Blink & Low Power Mode during last 30 minutes
  • Operational temperature -20C to +43C
  • T4 Temperature rated
  • Adjustable swivel head
  • Anti-Static Protective Lens System
  • Optional Scaffold Bracket
View Complete Details

Recessed Green LED Helideck Perimeter Lights

  • Operating voltage 100-254Vac; 50-60Hz / 20-30Vdc
  • Power consumption 4.5W (6VA) ac / 4W dc
  • Connection details M4; two M25x1.5 cable entries
  • Earth connection internal M4 and external M6
  • Dimensions (Ø x H) Ø298 x 111mm
  • Weight 9.1kg
  • Design degree of protection IP66
  • Operating temperature range -40°C to +60°C

Explosion proof recessed Green LED helideck perimeter lights. The design is based on low power long life LED technology and use of stainless steel. These fittings meet the regulatory requirements for ICAO, CAP437 and IMO. Operating voltage: 100-254V AC; 50-60Hz or 20-30V DC. Lighting intensity 30cd. Reliable recessed mounted helideck perimeter light. Low cost of ownership. Low power consumption. Serviceable unit, parts are interchangeable. Certified for Zone 1 and 2 areas with increased gas explosion hazard. Compact design, meeting the maximum 50 mm height restrictions of IMO. Intensity main beam 30cd green (CAP437). Impact resistant dome and stainless steel 316 body. Spacious, cable connection compartment. Photometric test of independent institution.

View Complete Details

Lumin EX LED Worklight

Description

The new generation Zone 1 & 2 certified SA LUMIN EX LED Worklights are designed with you, the user, in mind. Advanced LED technology is combined with exceptionally low cost of ownership to provide complete peace of mind. Exceptional cable gland and socket protection further improves the reliability of this product. The SA LUMIN LED Worklight 200 provides 360 of light output at up to 8000 lumens, yet only weighs 2.7kg.

Specifications:
  • ATEX and IECEx Certified for Zones 1 & 2 (gas), 21 & 22 (dust)
  • High Power LED technology
  • 360 light output
  • Low cost of ownership
  • Linkable versions available
  • Advanced diffuser system
  • Enhanced cable gland and socket protection
  • Lightweight and compact
  • Tough and durable
  • High light output
  • Exceptionally reliable
  • Waterproof and dustproof
  • T4 Temperature rating
  • Supplied with Adjustable Hanging Straps and Protective Film
  • Vessel Entry Kit available
View Complete Details

POWERNET PNLT Transformer

The new SA POWERNET PNLT Transformer is an ATEX approved (Zones 1 and 2, 21 and 22) Transportable Transformer with a capacity of no less than 3.8KVA (110V or 230v). Continuously rated, the PNLT will deliver power safely wherever you need it. It is a thoroughbred SA product that has been painstakingly developed, to be highly durable yet extremely easy to use. Transportation is simple with a wraparound protective marine grade stainless steel frame, fork lift points and certified lifting points. Weighing in at under 100kgs and developed to fit two on a Euro pallet, this unit is highly compact.

Specifications:
  • ATEX & IECEx Certified for Zones 1 and 2 (gas), 21 and 22 (dust)
  • 3.8KVA continuously rated
  • Safe construction
  • Dynamic load tested
  • Suitable for use down to -40C
  • Tough and durable
  • Compact and stable
  • Waterproof and dustproof
  • Integrated storage for 10m of supply cable
  • Easy maintenance
  • MCB and RCD Protection
  • Certified Transportable
View Complete Details

PNEL ATEX Extension Lead

Description

Built to the highest standards for exceptional reliability, the SA POWERNET EX Extension Leads deliver power to hazardous areas effectively and with minimum hassle. ATEX compliant, tough and durable, compatible with all SA lighting equipment and supplied ready to use

Specifications:
  • ATEX Certified for Zones 1 and 2 (gas), 21 and 22 (dust)
  • Tough and durable
  • Fast delivery times
  • Waterproof and dustproof
  • Compatible with SA LUMIN Worklights
  • Cost Effective
View Complete Details

ATEX Blast Light

Description

With direct illumination straight onto the work focus, our Blast Light can directly improve productivity levels by eliminating the need to go back over missed areas. A quick-release hose clamp, disposable protective lens system and 20m of braided cable make it easy to use, while a penetrating beam shines right through dust, cutting the need to wait for clear air before inspection.

Specifications:
  • ATEX Certified for Zones 1 and 2 (gas), 21 and 22 (dust)
  • Penetrating beam of light
  • Waterproof and dustproof
  • Easy to use
  • Replaceable Protective Lens System
  • Quick release hose clamp
  • Lightweight
  • T4 temperature rating
  • 24V operating voltage
  • Lens Protection Cap
  • Available with a Water Jetting Clamp
  • Compatible with the SA POWERNET 400V Transformer
  • Compatible with the SA LUMIN LED Vessel Entry Kits
View Complete Details

PNER ATEX Extension Reel

Description

The worlds first 'off the shelf' extension reel. Designed and built to withstand the most demanding conditions, the SA POWERNET EX Extension Reel is highly portable, stable, waterproof and dustproof, and comes in a wide range of variants accommodating different plug and socket combinations, cable types and voltages.

Specifications:
  • ATEX Certified for Zones 1 and 2 (gas), 21 and 22 (dust)
  • Highly portable
  • Tough stainless steel construction
  • Waterproof and dustproof
  • Compatible with SA LUMIN Worklights
  • Large number of variants available
View Complete Details

PNSB ATEX Splitter Box

Description

The SA POWERNET EX Splitter Box safely provides four 16A socket outlets in any environment. The rugged, waterproof and dustproof design makes our box practically indestructible, and it's supplied ready for use in full 'plug-and-play' state. Available in a range of voltage options, and usually available for next-day delivery.

Specifications:
  • ATEX Certified for Zones 1 and 2 (gas), 21 and 22 (dust)
  • Tough and durable
  • Fast delivery times
  • Waterproof and dustproof
  • Compatible with SA lighting systems
View Complete Details

PNDU ATEX Mains Distribution Unit

Description

Power where its needed with no requirement for a hot work permit or standby man. The first link between your power supply and your temporary system, our MDU can connect to welding sockets to greatly increase your power supply options, putting power where you need it to complete the task in hand. By avoiding the need for hot work permits and a standby man, it can pay for itself in days. A true plug-and-play system, our MDU connects to a 440V 63A supply, splitting the power to 32A or16A sockets. It's also extremely portable, weighing in at 55kg, and with a 10m input cable it can be easily moved by personnel without the need for lifting equipment.

Specifications:
  • ATEX Certified for Zones 1 and 2 (gas)
  • Tough and durable
  • Full MCB protection
  • Easily transportable
  • Weighs only 55kg including cable
  • Waterproof and dustproof
  • Easy maintenance
  • Internal safety shield
View Complete Details

ATEX LED Portable Compact Floodlight

Description

An extremely compact version of the new SA LUMIN Floodlight, the SAFL200 still packs an exceptional punch with a light output at 2500 lumens to your work area with a light coverage of 6.5m2 at 5m using the latest LED technology. Complete with an adjustable swivel head, you can direct the light to exactly where you need it. Operational in temperatures of -50C to +55C, you can successfully operate this light in many global locations. Available with an optional protective shield, protective film, and scaffold bracket, the SA LUMIN ATEX LED Compact Floodlight is extremely maintenance friendly with in-built voltage drop protection and a 5 year warranty.

Specifications:
  • ATEX and IECEx Certified for Zones 1 and 2 (gas), 21 and 22 (dust)
  • Certified Portable
  • High Power LED Light Beam
  • 6.5m2 light coverage at 5m
  • 5-year warranty
  • Maintenance Friendly
  • Operational temperature -50C to +55C
  • In-built Voltage Drop Protection
  • Waterproof and dustproof
  • Toughened Glass
  • T4 Temperature rated
  • Adjustable swivel head
  • Anti-Static Protective Lens System
  • Optional Scaffold Brackets
  • Vessel Entry Kits Available
View Complete Details

SA Lumin EX LED Emergency Worklight

Description

The SA LUMIN EX LED Emergency Worklight brings all the features and benefits of our standard Worklights to the workplace including smooth, eye-friendly light, a robust, almost unbreakable design and practically zero maintenance, but has a built-in Lithium-ion battery that provides emergency lighting for up to 90 minutes following a power failure. In most emergencies thats enough to evacuate a work area, tank or confined space safely, and could mean the difference between life and death. Like the standard model, it can be daisychained for larger areas and works with our SA LUMIN Fixing System for fast, secure fixing to most surfaces.

Specifications:
  • ATEX and IECEx Certified for Zones 1 & 2 (gas), 21 & 22 (dust)
  • High Power LED technology
  • Low cost of ownership
  • Linkable versions available
  • Advanced diffuser system
  • Enhanced cable gland and socket protection
  • Lightweight and compact
  • Tough and durable
  • High light output
  • Exceptionally reliable
  • Waterproof and dustproof
  • T4 Temperature rating
  • Supplied with Adjustable Hanging Straps and Protective Film
  • Vessel Entry Kit available
View Complete Details

ATEX Ventilation Fan

Description

Weighing only 12kg and just 35cm wide, the SA CYCLONE EX 20cm Fan can be moved quickly and easily into the most cramped and restricted space, yet still manages to shift 1660m3 of air per hour. Built from ultra-tough, anti-static polymer you can quickly connect a 5 or 10 metre duct, with couplers available for longer lengths where required.

Specifications:
  • ATEX & IECEx Certified for Zones 1 and 2
  • Extremely compact
  • Operates on 50 or 60Hz
  • Used as a blower or exhauster
  • Tough and durable
  • Lightweight only 12kjg
  • Anti-static polymer housing
  • Heavy duty motor
  • Quick-Couple Canister system available
  • Compatible with the SA CYCLONE Anti-static Ducting
View Complete Details

Anti Static Ducting & Duct Couplers

Description

With our superbly flexible, adaptable ducting and couplers you can quickly design and implement a system to your precise requirements, in virtually any environment. Built from anti-static reinforced polymer with integrated steel helix wire for strength, this ducting is ATEX approved for Zones 1 and 2. It's been tested to extremes in independent laboratory trials and passed both anti-static and flammability tests. Designed to work seamlessly with both the SA CYCLONE EX Fans and the SA FLEXIHEAT EX Heaters.

Specifications:
  • Anti-static
  • Flame retardant
  • High quality construction
  • Various lengths and widths of Ducting available
  • Very short lead times
  • Straight, Y-piece, and reducing couplers available
  • Compatible with the SA FLEXIHEAT Heater
  • Compatible with the SA CYCLONE Fans
View Complete Details

SAV ATEX Venturi Air Mover

Description

The market-leading air-driven ventilator, it has no moving parts, and instead uses high velocity compressed air to create a pulling action and a subsequent large volume displacement through a diffuser, connecting to ducting or hoses where required. The smallest unit weighs just 2kg not much more than a large torch. With no moving parts, our Venturi units are exceptionally reliable and require virtually no maintenance.

Specifications:
  • Powered by compressed air or saturated steam
  • Tough and durable
  • Anti-static polymer housing
  • Highly reliable
  • Minimal maintenance
  • Cylindrical mixing chamber delivers higher induction rates
  • Fits standard API openings
  • Earth lead and clamp available
  • 3 sizes available 13cm, 20cm, 30cm
  • Compatible with the SA CYCLONE Anti-static Ducting
View Complete Details

Proof LED Helideck Perimeter Lights

  • Operating voltage 100-254Vac; 50-60Hz / 20-30Vdc
  • Power consumption 2.5W (4VA) ac / 2W dc
  • Connection details M4; two M25x1.5 cable entries
  • Earth connection internal M4 and external M6
  • Dimensions (L x W x H) 161 x 161 x 111mm
  • Weight 3.6kg
  • Design degree of protection IP66
  • Operating temperature range -40°C to +60°C
Description

Explosion proof LED helideck perimeter lights to meet the demanding requirements of offshore environmental conditions. Available in Blue, Green or Yellow. The design is based on low power long life LED technology and use of stainless steel. These fittings meet the regulatory requirements for ICAO, CAP437 and IMO. Operating voltage: 100-254V AC; 50-60Hz or 20-30V DC. Lighting intensity available from 10cd 200cd, see datasheets on downloads.

View Complete Details

ILED Aquarius Helideck Floodlight

  • Light Source LED
  • IP Rating IP66
  • Luminous intensity 15, 000 cd
  • Average power 40 W
  • Light colour White
  • Ambient temperature -40 °C up to +55 °C
  • Burning position Universal
  • (Re)ignition Immediate
  • Voltage range 95 – 250 Vac
  • Power factor/Cos φ >0.90
Description

The ILED Aquarius Helideck Floodlight is made with an anodized, marine grade aluminium casting, making it highly resistant to seawater environments and therefore perfectly suitable for marine applications. The integral mounting bracket allows the unit to be easily fixed and the direction of the beam in the horizontal to be adjusted. The light cover is made of clear toughened glass which is extremely shock resistant and break proof with a Fresnel (PMMA) lens. The high Power LEDs in combination with the fresnel lens produce a superior light output. A special design feature of this product is in the heat management the ILED Aquarius Floodlight has a series of cooling fins with air ducts to dissipate the heat generated from the LEDs, which means that even in conditions of direct sunlight and high temperatures, the light unit continues to be cooled. The connection box is integral to the aluminium main housing and is manufactured with two cable entries for M25 cable glands.

The ILED Aquarius Floodlight is available as either an Ex-hazardous Area or Industrial Safe Area-version.

  • IEC protection classes: Class 1
  • Lens: Toughened glass with internal fresnel lens (PMMA)
  • Housing: Marine Grade Aluminium Anodized
  • Weight of the light fitting: 11 kg
  • Package weight per piece: 12 kg
  • Package dimensions: 400 x 400 x 380 mm LxWxH
  • Standard version: Ex e junction box 2x M25x1.5 entries. Terminals suitable for max. 4 mm. Suitable for through wiring
View Complete Details

Explosion Proof LED Illuminated Windsock

Description

Designed with an internal LED floodlight to illuminate the windsock and prevent glare. The explosion proof illuminated windsock provides wind-speed and direction indication to pilots during landing and take-off for helicopter operations. Low cost and power consumption. No dazzling lights to pilots because of the internal sock illumination. Corrosion free due to stainless steel 316 body. With easy installation and various operating voltages. Fully integrated aeronautical obstruction light if required.

Specifications:
  • AC (110-254v) and DC (10-32v) versions
  • Optional 10 or 32cd steady burning red Aeronautical Obstruction Light
  • Zone 1 ATEX and IECEx Certified
  • Internal LED floodlight (max 8.5W)
  • Mounting Plinth identical to existing Orga Windsock for direct replacement.
  • Connection details: max. 4mm;two M25x1.5 cable gland entries
  • Earth connection: internal max.4mm and external M8
  • Dimensions (L x W x H): 609 x 460 x 677mm (excl. sock)
  • Weight: 20kg
  • Degree of protection: IP66
  • Operating temperature range: -20C to +60C
View Complete Details

Loop Splitter

Description

The SEM1200 is a current loop splitter that provides two isolated (4 to 20) mA passive outputs from a single passive (4 to 20) mA input.The output loops must be powered externally. It is housed in a 12.5mm wide DIN rail mount plastic enclosure with screw terminals for wiring.

Specifications:
  • 2 isolated 4-20 mA outputs from 1 4-20 mA input
  • High Accuracy
  • Galvanic Isolation
  • 12.5 mm Wide
View Complete Details

PH-Transmitter & Controller With Digital Display

Description

The Type 8205 has now been superseded by the Type 8202 click here:pH / ORP Type 8202

The pH transmitter is available in different models: A compact pH transmitter with integrated pH probe. It can be installed into pipes by using INSERTION Type S020 fittings or suitable installation materials. It can also be installed in tanks or containers by using an industrial immersion fitting. Also, a remote pH transmitter, for panel or wall mounting, to connect to a pH probe mounted into a Brkert probe holder Type 8200 (max. 10 m) which can be installed into pipes by using INSERTION Type S020 fittings or using its own particular connection. It can also be installed in tanks or containers by using an industrial immersion fitting.

Specifications:
  • This product has now been superseded by the Type 8202 click here:pH / ORP Type 8202
  • Compact, remote versions for DN15 to DN200
  • Fully configurable pH transmitter for all kinds
  • of pH measurement tasks
  • Large range of process connections with
  • various fittings
  • Multi language, menu-guided operation
View Complete Details

Universal Process Controller ECONTROL

Description

The universal 8611 controller is especially designed for compact control system applications. It can be connected with every non-Brkert Control valve by standard signal (4-20 mA, 0-10 V or PWM-output). The proportional & Integral (PI) process controller is equipped with many additional functions. The process value feedback can be supplied as one of three analog inputs; a standard signal (4-20 mA/0-10V)), frequency or RTD signal; directly to the universal controller. The process switching points can be set via a 4-20 mA or 0-10 V signal or with the keypad. Thanks to the proportional control capabilities, a wide range of control functions can be performed in a variety of liquids and gas medias.

Specifications:
  • Continuous, 2-point, 3-point & On/Off control
  • Ratio control function
  • Sensor inputs (4-20 mA, 0-10 V, frequency, RDT)
  • Control proportional, process and motor valves
  • Brkert proportional valves and flowmeters
  • are memorized
  • 1/16 DIN size panel version
View Complete Details

Non-Contacting Ultrasonic Level Measurement

Description

Ultra 5 offers the ultimate flexibility in ultrasonic control and measurement. It is user-configurable to measure level or volume, provide advanced pump control or measure open channel flow to BS ISO 1438 and 4359 and gives you the ultimate flexibility of: five assignable relays with extra alarm options such as pump efficiency; extra pump control functions including pump run-on and pump exercising; storm and aeration control; differential control using two transducers, the addition of further relays in OCM applications.

Specifications:
  • Solids or liquids level measurement
  • Linearisation for tank shapes
  • Advanced pump control choices
  • Pump efficiency alarm
  • Optional 4-20mA input
  • Wide choice of flumes and weirs in OCF
  • Easy prompt set up
  • DATEM software
View Complete Details

MxCONTROL Multifunction Controller

Description

The mxCONTROL multifunction controller, is a microprocessor controller designed to automate the control of process variables within a water treatment system (e.g. boiler, cooling tower or Reverse Osmosis system). Sophisticated electronics and state of the art control algorithms ensure that optimum process control is maintained at all times, with minimal operator intervention.

Specifications:
  • Data and event logging
  • One controller hardware with dozens of
  • configuration possibilities quickly downloaded
  • via SD card (supplied) or via USB interface
  • Ethernet or modem communication with email
  • or call event notification & numerous
  • input/output control signals
View Complete Details

GPRS & SMS Data Logger

Description

XiLog+ series is a new range of remote data loggers available from Primayer. Every logger can be programmed for GPRS or SMS communications. It is available in single to nine channel models for use with a wide variety of sensors for monitoring water networks. All loggers may be configured to use GPRS or SMS remote communications for periodic reporting. Transmission period can be set from 15 minutes to 24 hours. The state-of-the-art antenna enables XiLog+ to operate from below ground in most locations. In areas of poor GSM/GPRS coverage an external antenna option is available.

Specifications:
  • One, two, three and nine channel models
  • High performance below ground antenna
  • Data transmission every 15 minutes
  • Contact the logger as required
  • Alarms with defined high and low profiles
  • Wide range of sensors and high accuracy
  • Powered up to 5 years (depend configuration)
  • Robust and waterproof to IP68
View Complete Details

3G & GPRS Leak Detection Logger

Description

Phocus3m is an acoustic logger that automatically detects leaks on water distribution networks. Deployed underground it utilises low cost GPRS/3G communications without the need for costly above ground technology.

Specifications:
  • Remote leakage identification to reduce leak run-time and improve efficiency
  • PrimeWeb map based data available
  • Phocus noise algorithm reduces incidence of undetected leaks
  • Three sample periods to separate usage from leakage thus reducing false alarms
  • No drive-by required reduces operational costs
  • No infrastructure above ground required
  • One, small, low cost logger per installation
  • Embedded roaming SIM for optimum communications
View Complete Details

Temp & RH USB Logger- High Accuracy

Description

The SL54USB-A offers increased relative humidity accuracy over the standard SL54USB. The SL54USB data loggers plug directly into the USB port of a PC for configuration then removed and placed where monitoring is required. After monitoring the data logger is placed back in the USB slot for data retrieval. They have the ability to record up to 8, 000 data points and have a measuring temperature range of -10C to +85C and 0 to 95%RH. The SL54USB data loggers are fully compatible with free software TempIT-Lite allowing the logger to be set up and the data read and displayed in graphical format. TempIT-Lite can be upgraded to TempIT-Pro which providing additional features.

Specifications:
  • Internal battery
  • Temperature range -10C to +85C
  • Measuring 0C to +70C Communicating
  • Accuracy 0.5C from -10C to +65C
  • RH accuracy 2%RH
  • Readings 8192 4096 (low/high res mode)
  • IP Rating: IP20 0 to 95% RH Non Condensing
View Complete Details

Borehole Or Submersible Level Data Logger

Description

The SL964 from Signatrol can now be supplied with a triband GSM modem that allows the operator to dial in to remote sites and view the current level and temperature (if option is chosen) as well as download stored data. It is a battery powered data logger suitable for measuring fluid level and temperature. The self-contained data logger is particularly suited for portable installations or where traditionally it has not been possible to provide conventional power supplies. A high accuracy, stainless steel, submersible pressure transducer provides level measurement for recording by a high-resolution data logger mounted in the same stainless steel assembly.

Specifications:
  • Internal battery (10 years max)
  • Minimum 0 to 100 mBar / 0 to 1m water gauge
  • Maximum 0 to 25 Bar / 0 to 250m water gauge
  • Temperature range 0C to +70C
  • Temperature -25C to +85C optional
  • Number of readings: 130, 000
  • Sample every 2 seconds to 24 hours
  • Ingress protection: IP68
View Complete Details

Paddlewheel Tx For Batch Control With Digital Display

Description

The batch controller is specially designed for use in neutral and slightly aggressive, solid-free liquids. The device is available in different models: A compact batch controller with integrated paddle-wheel sensor. A remote batch controller for panel or wall mounting for connection to Brkert 8020 / 8030 / 8031 / 8041 / 8071 sensors or to a flow sensor from the market; sensors with open collector output, relay reed output or coil can be operated by this batch controller.

Specifications:
  • Compact or remote version for
  • DN06 to DN400, PN10
  • Dosing
  • Automatic calibration: TEACH-IN
  • Possible check of input/output signals
  • Batched volume and totalizers displayed
View Complete Details

Mass Flow Controller

Description

The MFC / MFM type 8745 is suitable for the mass flow control of high flow rates. Type 8746 can be configured as MFM or MFC. Optional, four different gases can be calibrated. The thermal inline sensor is located directly in the main gas stream and therefore reaches very fast response times. A direct-acting proportional valve as regulating unit guarantees high sensitivity.

The integrated PI controller ensures outstanding control characteristics of the MFC / MFM. MFC Type 8745 is available in two versions: with electromagnetic proportional valve and with motor-driven proportional valve.

Specifications:
  • Nominal flow ranges from 20 lN/min up to 2500 lN/min
  • High accuracy and repeatability
  • Very fast response times
  • Easy device exchange through configuration memory
  • Communication via standard signals or Industrial Ethernet
  • Electromagnetic and motor-driven valve actuation available
View Complete Details

Electronic Indicator

Description

The GMTX electronic indicator with microprocessor enhanced performance and LCD panel display of flow rate and total, designed for use with a metal tube variable area flowmeter for liquid, gas or steam measurement. Suitable for use with body options, the VAMPIRE (Variable Area Micro Processor Indicator Readout Electronics) has a totally solid state measurement system, eliminating mechanical hysteresis errors. Microprocessor interpolation between flow data points, stored in factory calibrated look-up tables, gives an improvement to 1% accuracy for this technique.

Specifications:
  • 4-20mA transmitter
  • Intrinsically safe approval
  • Liquid or gas flow calibration
  • Built-in flow totaliser
  • Operator adjustable high and low alarms
  • 1% accuracy
  • VA meter reliability
  • Program setting password protection
View Complete Details

Insertion Sensor With Converter

Description

The MS 3770 insertion sensor is suitable for mounting in non-pressurised pipe lines with diameters ranging from ND 80 to 8000 mm. It is ideal for pipe line monitoring and for the HVAC market. For further information, see the technical data sheet downloadable below.

Specifications:
    • Stainless Steel AISI 304/316
    • Wide choice of pipe diameters
    • Nominal pressure from PN 16 to PN 64
    • Threaded or flanged connections
    • Liquid temperature: from -20 to 150C
    • Lining material: PTFE
    • Electrodes material: Hastelloy C
    • Accuracy: +/- 2% of the read value
View Complete Details

Microflow Sensor With Converter

  • Body material SS AISI304/316
  • Nominal diameter from ND 3 to ND 20
  • Flow range 12.500 l/h
  • Nominal pressure from PN 16 to PN 40
  • Liquid temperature da -20 a +150°C
  • Lining material PTFE
Description

The MS 501 'Microflux' sensor is the smallest instrument of the series, with a wide range of process connections for all the applications and a wide choice of electrodes materials. Accuracy and repeatability data are according to the chosen converter.

View Complete Details

Open Channel Flow Measurement

Description

Pulsars MicroFlow-i delivers accurate, repeatable velocity measurement for liquid flow, either as an individual sensor or by providing HART communication protocol or a 4-20mA loop powered signal into a system. For flow volume measurement, velocity x area provides a cost-effective alternative to a channel restriction, such as a flume, and viable solution in situations where system hydraulics do not permit the installation of any primary measurement device.

MicroFlow-is extremely low power consumption makes it the ideal velocity solution for sewerage network monitoring (CSO) and all remote installations where mains power is unavailable.

Its lightweight, compact design makes installation simple, especially within confined spaces and requires no interruption to normal operational flow.

Specifications:
  • Non-contacting Flow Measurement
  • IP68
  • Extremely low power consumption
  • Lightweight, compact design
  • Minimal installation costs
  • No interruption to service
  • Maintainence-free
  • Cost-effective
  • Optional Mounting Bracket available
View Complete Details

Adjustable Plastic Paddle Switch

  • Cables 3 x 460mm 18AWG wire
  • Operating 100.00 °C and 10 BarG
  • Pipe Size 1″ NPT
  • Body Polyphenylene sulphide (PPS)
  • Wetted Materials Polyphenylene sulphide,
  • Dimensions 238 x 42mm diameter
  • Switch SPDT, 5A 120/250V AC
Description

Made from chemical resistant and durable polyphenylene sulphide this plastic paddle flow switch is suitable for either liquid or air. When flow stops the Stainless steel vane spring moves the vane and activates a switch to stop/start a pump, alarm or open/close a valve. The plastic vane is trimmable to allow for installation on pipes from 1 to 6.

View Complete Details

Platon Liquid Low Flow Alarm

Description

For liquid low flow or flow failure alarm on cooling systems, water heaters or lubrication systems, the Platon LF flow switch is a rugged sensor with simple electrical reed switch output. Installed in a vertical line with flow upwards, normal flows lift the float in the sensor. A magnet encapsulated in the float then actuates a reed switch, giving contact closure. Should the flow drop to below the preset alarm level, the float falls to the rest position and the contacts open to give an alarm output.

Specifications:
  • Low cost flow alarm
  • Simple rugged construction
  • Brass, BSP connections
  • Selectable alarm trip level (factory set)
  • No glands or seals
  • Stainless Steel and other special OEM versions
  • available
View Complete Details

Pulsar Flow Pulse

Description

Flow Pulse is a unique, non-invasive flow monitor that clamps to the outside of a pipe and is simply secured with a screwdriver. Flow Pulse offers you exceptional repeatability at a fraction of the cost of an equivalent magflow meter. It can reliably monitor flow across a variety of pipe materials including rigid plastic, stainless steel, cast iron and even corrugated pipes. Flow Pulse fires ultrasound through the pipe wall at 90 degrees to the flow via a tangentially mounted high-output ceramic. Ultrasound is refracted at angles across the axis of the flow and is then reflected from bubbles, particles and vortices in all directions and at a wide range of frequencies. The returned signal is analysed using Flow Pulse's Refracted Spread Spectrum Analysis (RSSA) digital signal processing platform to derive flow information. RSSA analyses and integrates the received signals over a wide frequency range, then slices them for real-time analysis and flow rate calculation. Flow Pulse can either operate as a stand-alone device or can interface directly with Pulsar's dedicated wall mounted Flow Monitor.

Specifications:
  • Small size for simple installation
  • Suitable for dirty and turbulent liquids
  • Manual programming
  • No complicated process connections
  • Robust stainless steel construction
  • Low purchasing costs
  • Simple operation
  • Available in two versions, 30 to 350mm or 30mm to 1250mm pipe diameter
View Complete Details

LED Industrial Bulkhead

  • Weight 5kg (11.0lbs) Standard, 6kg (13.2lbs) Emergency
  • Power 34W standard, 37W emergency
  • Temperature range 50°C to +46°C (-20°C emergency variants)
  • Dimensions 288 x 220 x 122mm (11.3 x 8.7 x 4.8 inch)
  • Termination Incoming terminal block suitable for looping 4 core 4mm² cable
  • Power Factor >0.95
Description

The SPARTAN Bulkhead range is designed specifically for industrial applications which require high performance, high reliability, White-Light illumination. Using Raytecs field-proven, long-life LED technology, SPARTAN Bulkhead is suitable for a wide range of industrial applications. SPARTAN Bulkhead is ideal for applications where space is restricted with its compact, low profile design, which also allows easy access to the back of the unit with rear cable entries so cabling can be hidden and protected from damage. Housed in marine grade aluminium, SPARTAN Bulkhead is IP66 and IP67 rated and can survive the most extreme environments.

SPARTAN Bulkhead is available in a range of different beam patterns, both circular and elliptical, with revolutionary interchangeable VARIO lens inserts which can be easily altered on site delivering the ultimate flexibility to specifiers, distributors and end users. Delivering high performance illumination of up to 2, 750 lumens, SPARTAN Bulkhead is also available as an emergency fitting with integral battery back-up which can run up to 100% light output under emergency conditions.

View Complete Details

LED Industrial Linear

Description

The SPARTAN Linear range is designed specifically for industrial applications and to retrofit existing fluorescent installations which require high performance, reliable, White-Light illumination. Housed in Marine Grade aluminium and using Raytecs field-proven, long-life LED technology, SPARTAN Linear is suitable for a wide range of industrial applications. SPARTAN Linears overall dimensions, fixing centres and gland entries are all compatible with commonly used traditional Ex e 2x18W fluorescent luminaires. The lumen output and light distribution also allows a direct, easy replacement of traditional fluorescent luminaires, meaning the customer can upgrade without complication and enjoy all the benefits of long life LED lighting while making regular lamp changes redundant. SPARTAN Linear is available as an emergency variant, and standard variants can be converted to an emergency fitting at any time on-site, thanks to a unique modular design.

This design also means key components can be easily accessed and serviced if required to make inspection and maintenance quicker and easier. SPARTAN Linear has a clear polycarbonate diffuser which is also available in various degrees of opaqueness to provide greater flexibility during installation. SPARTAN uses CoolExtrude thermal management technology, ensuring a much cooler LED operating temperature and up to 60% better heat dissipation compared to traditional lighting solutions, allowing the product to operate for > 10 years while still delivering a high lumen output of up to 2, 750 lumens.

Specifications:
  • Standard and Emergency Variance
  • Lumen Output 2750 Lm
  • Input 110-254v 50/60hz Ac Only. Low Voltage Option Also Available for standard variants only.
  • Consumption 34w, Emergency 37w
  • Ip Rating IP66 & IP67
  • Temperature Range-40 To +55C (-40 To 131F)
  • Weight 6kg (13.2lbs), Emergency 7kg (15.4lbs)
  • Dimensions 772 X 108 X 174mm (30.4 X 4.3 X 6.9)
View Complete Details

Trimod Besta Bilge Switch

  • Pressure max. 16 bar
  • Temperature -40 to +80°C
  • Medium density min. 750 kg/m³
  • Switch point position approx. in the middle of the switch pipe
  • Switch pipe 12 mm in 1.4571
  • Mounting bracket stainless steel 1.4571
  • Protective casing Length 80 mm, in 1.4571
  • Float Cylindrical float ø 44, 5 mm in 1.4571
  • Enclosure IP68 (8 m), (DIN 40050)
Description

For installation in ships, mostly under difficult conditions, such as the simultaneous presence of different fluids, such as oils, water with solid content and petrol.

Bilge switch with protection class IP68 (8 m) and test function, maintenance-free, vertical installation. Mainly for use in shipbuilding.

The bilge float switches are designed for general usage on ships and for industrial purposes. These bilge switches are primarily intended for extremely high mechanical load and especially dirty liquids such as found in e.g. bilge wells, fresh water tanks, tanks for hydraulic and diesel oil, plant construction,

Specifications:
  • Opener / Closer: 230V AC, 100 VA, 1A AC 230V DC, 50 W, 0.5A DC
  • Change-over switch: 230V AC, 40 VA, 1A AC 230V DC, 20 W, 0.5A DC
  • Switch function: Opener / Closer / Change-over switch with a rising liquid level
  • Cable Output: Standard cable length 2 m, 2 x 1.5 mm, 3 x 1.5 mm
View Complete Details

Standard Range Level Switches- Electric

  • Density of the liquid 0.7 kg/dm³
  • Operating differential 12 mm, fixed
  • Wetside Stainless steel (CrNiMo)
  • Housing Seawater resistant die cast aluminium
  • Flange Square 92 x 92 mm, 92 mm PCD
  • Enclosure IP65
Description

The Trimod Besta standard range electric level switches have a nominal pressure of PN 25 according to DIN. They have an operating temperature of between 0 and 300C with an ambient temperature between 0 and 70C. The wetside material is Stainless steel (CrNiMo) while the housing material is seawater resistant die cast aluminium and the enclosure is IP65 rated. The switch element is a microswitch SPDT with silver contacts and has a switch rating of 250 VAC, 5A or 30 VDC, 5A.

Specifications:
  • PN 25 according to DIN
  • 0 to 300C (ambient 0 to 70C)
View Complete Details

Guided Microwave Level Transmitter

Description

The Type 8185 is a level transmitter with cable or rod probe, designed for continuous level measurement. The unit is suitable for liquids, but also for solids, for industrial use in all areas of process technology. With measuring range of up to 32 m, the transmitter is best suited for tall vessels. Even process conditions such as strong steam generation, density fluctuations or changes of the dielectric constant do not influence the accuracy of the measurement. Buildup or condensation on the probe or vessel wall do not influence the measuring result.

Specifications:
  • Universal level transmitter for liquids & bulk
  • materials
  • 420 mA/Hart 2 wires
  • Insensitive to dust and steam
  • ATEX approvals
View Complete Details

Gen Purpose Radar Level Transmitter

Description

The Type 8137 is a non-contact radar level transmitter for continuous level measurement. The unit is available in two versions; with thread and horn antenna ( 40 mm) particularly suitable for use in small tanks and process vessels for measurement of practically any product. Also, with flange and horn antenna ( 40 or 75 mm) particularly suitable for use in storage tanks and process vessels for measurement of products such as solvent, hydrocarbons and fuels under extremely difficult process conditions.

Specifications:
  • Compact for level measurement up to 30m
  • 4 20 mA/Hart 2 wires
  • Adjustable with PC
  • ATEX approvals
View Complete Details

Vibrating Level Sensor/Switch

Description

The 8112 is a vibrating level switch for liquids, using a tuning fork for level detection. It is designed for industrial use in areas of process technology and can be used in liquids. Typical applications are overfill or dry run protection. The Type 8112 is available with different sensor length using tube extension. The right length can be adapted thanks to a lock fitting. Due to the simple and rugged measuring system, the 8112 is virtually unaffected by the chemical and physical features of the liquid. It works even under unfavourable conditions such as turbulence, air bubbles, foam generation, buildup or varying products.

Specifications:
  • For universal use as overfill or dry run
  • protection system
  • Setup without adjustment
  • For food and beverage industry thanks to
  • surface finishing < 0.8 m
  • ATEX approvals
View Complete Details

Bilge Switch

  • Pressure max. 16 bar
  • Temperature -40 to +80°C
  • Opener / Closer 230V AC, 100 VA, 1A AC – 230V DC, 50 W, 0.5A DC
  • Change-over switch 230V AC, 40 VA, 1A AC – 230V DC, 20 W, 0.5A DC
  • Switch function Opener / Closer / Change-over switch with a rising liquid level
  • Cable Output Standard cable length 2 m, 2 x 1.5 mm², 3 x 1.5 mm²
  • Medium density min. 750 kg/m³
  • Switch point position approx. in the middle of the switch pipe
Description

For installation in ships, mostly under difficult conditions, such as the simultaneous presence of different fluids, such as oils, water with solid content and petrol.

Bilge switch with protection class IP68 (8 m) and test function, maintenance-free, vertical installation. Mainly for use in shipbuilding.

The bilge float switches are designed for general usage on ships and for industrial purposes. These bilge switches are primarily intended for extremely high mechanical load and especially dirty liquids such as found in e.g. bilge wells, fresh water tanks, tanks for hydraulic and diesel oil, plant construction,

  • Switch pipe: 12 mm in 1.4571
  • Mounting bracket: stainless steel 1.4571
  • Protective casing: Length 80 mm, in 1.4571
  • Float: Cylindrical float 44, 5 mm in 1.4571
  • Enclosure: IP68 (8 m), (DIN 40050)
View Complete Details

Pressure Gauge With Diaphragm

Description

The differential pressure gauge is suitable for universal use in areas with special requirements for measuring gaseous, liquid and aggressive media. Application areas are level measuring, filter monitoring, flow measuring. Because of its robust design, the device is suitable for use in tough environments.

Specifications:
  • Case with blow-out device
  • Case and measuring flange of stainless steel,
  • diaphragm of Duratherm
  • High overload protection up to 5 times
  • (option: up to 20 times)
  • Nominal ranges 040 mbar up to 025 bar
  • (diffential pressure)
  • Accuracy class 1.6 per EN 837-3
View Complete Details

Redox-Probe Holder

Description

The probe holder Type 8200 can be installed into pipes or tanks by using G2 connection (using a Brkert INSERTION fittings Type S020), G1 connection, G1 connection, varivent connection, clamp connection, sanitary connection (according to DIN11851) or fixing kit for immersion fitting.

Specifications:
  • For many different installations and applications
  • Large range of probe holders
  • Versions for DN15 to DN200
View Complete Details

Conductivity Sensor For Hygienic Processes

Description

The 8221 Hygienic conductivity sensors are used to determine electrical conductivity in solutions. Due to their hygienic design and the robust layout, these conductivity sensors are suitable for use under demanding conditions in food & beverage, pharmaceutical, biotechnology and the general chemical industry. The sensors are based on the 4-electrode principle which excludes polarization phenomena normally observed with 2-electrode sensors. The engineered design guarantees an excellent linearity over a wide conductivity range of more than 6 decades. An integrated temperature sensor (Pt1000) is a standard feature of all versions.

Specifications:
  • 4-electrode technology
  • Extended measuring range 0.1 S500 mS/cm
  • Hygienic connections, materials, surface finish
  • Suitable for steam sterilization, CIP
  • All wetted parts FDA approved
View Complete Details

MultiCELL- Transmitter / Controller

Description

The 8619 multifunction transmitter/controller is a microprocessor transmitter/controller for connection of sensors which deliver raw signals for pH, O.R.P. and conductivity and flow via pulses. It is ideal for measurement and control and dosing processes e.g. in water treatment plants (like boiler, cooling tower or reverse osmosis systems) and food and pharma plants. Modularity offers high flexibility for adjusting it to the applications and so excellent price to functionality relation. Sophisticated electronics and state of the art control algorithms ensure that optimum process control is maintained at all times with minimal operator intervention.

Specifications:
  • Compatible (flow, pH/O.R.P. and conductivity)
  • Simple, intuitive user interface
  • Large adjustable backlit display
  • Basic transmitter/controller
  • Hardware extension possibilities
  • Functionality extendable by software options
  • Data logging
View Complete Details

PH Measuring System

Description

The 8201 pH measuring system is suitable for measuring absolute pH values in liquids between pH 0 and pH 12 at medium temperatures of up to 140C and process pressures of max. 6 bar. Due to its hygienic design and the robust glass-free layout, this model is particularly suitable for use in hygienic processes. An example would be the production of foods and active ingredients, during which the pH value of liquid mediums including those which are viscous or contain solids is measured.

Specifications:
  • Sterile design
  • Extremely robust and unbreakable construction
  • CIP-compatible, in-line sterilizable
  • Extremely long service life
  • Long calibration intervals
  • Especially suitable preparing foods and drinks
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us