Audio Recorders, Mixers & Transmitters #6534716

Provide 2STM-1 uplink interface with standard optical fiber

Supports two operation modes toward the network: two independent STM-1 links (no protection) with total connection capacity is 63 timeslot (one STM-1); and dual-link operation with 1+1 single-ended multiplex section protection (unidirectional protection), with automatic protection switching (1+1 APS protection)

Support flexible topologies such as point-to-point, chain or ring network

Offer various tributary interfaces: E1 interface, Ethernet interface and V.35 interface

overview

asakeymemberofbaudcommetroedge-expresssdh/msppproductfamily, bd-stm1-tm seriesterminal multiplexer delivers bonded e1 lines, ethernet services and v.35 links over legacy sdh networks. Installed at the customer site or directly on stm-1 access ring, the stm-1 terminal multiplexer leverages the sdh infrastructure for lan connectivity and internet access, while providing leased line services to end users.

the ethernet frames are encapsulated in sdh frame by using gfp (generic frame protocol) and transported through the sdh network in a vc-12 group, configuring the bandwidth of ip channel in increments of 2mbps.the sdh stm-1 multiplexer introduces lcas technology and vcat technology to benefit the sdh network to better fit busty data traffic. Each ethernet module groom up to two wans, aggregating two direction ethernet services into sdh networks. The pdh traffic and v.35 traffic are mapped into the sdh frame; enabling e1 and v.35 link to support cross connection, and can be terminated at any point on the network.

the multi-service stm-1 terminal multiplexer provides console interface for management. The ems network management system supports remote configuration and monitoring, reducing operating expenses, eliminating technical visit and maximizing network performance and uptime.

bd-op-mux256 is a multi-service fiber multiplexer which can realize 256channel voice and 4*10/100/1000m gigabit ethernet over fiber transmission.the fiber multiplexer is rack mount device whichhave 16slots for 16voice card or e1 card.the device support snmp andconsole management.

description

the bd-lan3000 ismultiservice fiber optical multiplexer with snmp&lcd&console management.it is created with 16e1+4*100mfull speed ethernet capacity of transmission interfaces. The fiber multiplexer can provide various interface modules for voice, data and video services in cities and industrial districts. Its optional interfaces support multiservice transmission of large customers and customer groups such as mses, governmental organizations, schools and intelligent residential areas.
functions:features:

largest transmission capacity is16e1, 4*10/100methernet dataand 2 aux port for other data such as rs232/rs485/rs422.

flexible configuration:providing 4 plug-in i/o slots which can insert various modules to meet different user requirements and customizations, each slot can use the following service cards:

v4-channel e1 module, providing 75ohm or 120ohm(optional).

v2-channel v.35 module, providing 4 standard v.35;

v4-channel fxs/fxo voice module;

v4-channel rs232 module;

1+1 optical redundancy backup: provide two plug-in i/o slots for dual optical interface cards. Protection of dual optical interface available to ensure that business will not be interrupted.

providing 2*sfp slotsfor optical port, it is easy for customer choose different sfp modules according to different application;

providingsnmpmanagement, lcdmanagement, consolemanagement (cli);

1 order wire port for hotline telephone.

support aps function (auto protect system) and als(automatic laser shutdown/reduction)

the 4*ethernet support vlan function, ethernet bandwidth can be set;

support double power for redundance, the power can becombination ac220v and dc-48v;

product characteristic
provides 4 channel e1/ g.703;
provides 14*10/100m ethernet;
provides 16 channel voice port, fxo and fxs for option;
provides12 channel rs232, rate supports 300-15200 bps for option;
ethernet port 10/100m, full/half duplex auto-adaptable and supports vlan;
ethernet port supports auto-mdix (twisted cable and straight cable auto-adaptable);
1-16 channel voice connection, supports calling indication;
voice port supports o port and s port, o port connects switch and s port connects users phone;
optical interface supports sc or fc or st connector, single modeor multimode fiber or wdm fiber.
fiber transmission distance up to 120km.

description:

16e1fiber optical multiplexercan multiplex to 16e1 signals for transmission over an optical fiber, resulting in reaching a longer distance without a repeaters and superior performance compared to copper media.

16e1 fiber optical multiplexer is the 16e1 point-to-point optical transport equipment that uses the fpga chips and it is easy to upgrade. It is single board structure and the largest transmission capacity is 16e1. The outer design use the standard 19 inches rack, so the volume is little, weight is light and operation is convenient and credit.16e1 fiber optical multiplexer, is use the pdh fiber transmission technologies. The 2m (e1) interfaces can connect with the exchanger, light loop device and multi-diplexer directly to form the mircomidi or the special network. Complete alarm function for 16e1, it is stable and easy to maintenance, install and small in size. It has one digital service telephone.

feartures:

• offer 16 x 2mb/s digital interfaces
• the supervisory control interface implements centralized monitoring and export the monitor and control information of this port and opposite port.
• one link to service telephone for duty contract
• 220vac & -48vdc power options and the positive and negative of dc-48v can be optional because there is the self-test circuit for the polarity inside th1e device
• standard 19/9.5 inches rack, little volume, light weight, steady capacity and convenient setup
• digital clock recovery circuit and digital smooth dpll adopted for 2.048mb/s port
• led indicators
• has 1+1 fiber protection for optional
• power supply redundancy : ac220 and dc-48v or dc-24v combination

product description:16e1 fiber optical multiplexer is the 16e1 point-to-point opticalfibertransport equipment that uses the fpga chips and it is easy to upgrade. It is single board structure and the largest transmission capacity is 16e1. The outer design use the standard 19 inches rack, so the volume is little, weight is light and operation is convenient and credit.16e1 fiber optical multiplexer, is use the pdh fiber transmission technologies. The 2m (e1) interfaces can connect with the exchanger, light loop device and multi-diplexer directly to form the mircomidi or the special network. Complete alarm function for16e1, it is stable and easy to maintenance, install and small in size. It has one digital service telephone.

features:

• offer 16x2mb/s digital interfaces
• offer one 10/100m ethernet channel for option
• the supervisory control interface implements centralized monitoring and export the monitor and control information of this port and opposite port.
• one link to service telephone for duty contract
• 220vac & -48vdc power options and the positive and negative of dc-48v can be optional because there is the self-test circuit for the polarity inside th1e device
• standard 19/9.5 inches rack, little volume, light weight, steady capacity and convenient setup
• digital clock recovery circuit and digital smooth dpll adopted for 2.048mb/s port
• led indicators
• has 1+1 fiber protection for optional
• power supply redundancy : ac220 and dc-48v or dc-24v combination

description:the 8e1fiber optical multiplexeris the 8e1 point-to-point optical transport equipment that uses the fpga chips and it is easy to upgrade. It is single board structure and the largest transmission capacity is 8e1and 4*100m wire speedethernet data. The ethernet bandwidth is set on base on multiple of 32k. The outer design use the standard 19 inches rack, so the volume is little, weight is light and operation is convenient and credit.

the 8e1 pdh fiber optical multiplexer use the pdh fiber transmission technologies. The 2m (e1) interfaces can connect with the exchanger, light loop device and multi-diplexer directly to form the mircomidi or the special network. Complete alarm function for 8e1, it is stable and easy to maintenance, install and small in size. It has one digital service telephone.

features:

• offer 8e1 digital interfaces

• offer four 10/100m ethernet channel for option
• offer order wire phone for option

• the supervisory control interface implements centralized monitoring and export the monitor and control information of this port and opposite port.
• one link to service telephone for duty contract
• 220vac & -48vdc power options and the positive and negative of dc-48v can be optional because there is the self-test circuit for the polarity inside th1e device
• standard 19/9.5 inches rack, little volume, light weight, steady capacity and convenient setup
• digital clock recovery circuit and digital smooth dpll adopted for 2.048mb/s port
• led indicators
• has 1+1 fiber protection for optional
• power supply redundancy : ac220 and dc-48v or dc-24v combination

description:

8e1 fiber optical multiplexer is the 8e1 point-to-point optical transport equipment that uses the fpga chips and it is easy to upgrade. It is single board structure and the largest transmission capacity is 8e1. The outer design use the standard 19 inches rack, so the volume is little, weight is light and operation is convenient and credit.8e1 fiber optical multiplexer, is use the pdh fiber transmission technologies. The 2m (e1) interfaces can connect with the exchanger, light loop device and multi-diplexer directly to form the mircomidi or the special network. Complete alarm function for 8e1, it is stable and easy to maintenance, install and small in size. It has one digital service telephone.

feartures:

• offer 8 x 2mb/s digital interfaces
• the supervisory control interface implements centralized monitoring and export the monitor and control information of this port and opposite port.
• one link to service telephone for duty contract
• 220vac & -48vdc power options and the positive and negative of dc-48v can be optional because there is the self-test circuit for the polarity inside th1e device
• standard 19/9.5 inches rack, little volume, light weight, steady capacity and convenient setup
• digital clock recovery circuit and digital smooth dpll adopted for 2.048mb/s port
• led indicators
• has 1+1 fiber protection for optional
• power supply redundancy : ac220 and dc-48v or dc-24v combination

description:
the30 channel voice multiplexerprovide a method of multiplexing up to 30 analog (pots) channels over a single pair of multimode or single mode fibers. Thevoice fiber multiplexersolves the problem of limited available fiber, reduces equipment space and lowers overall equipment costs.
in addition to voice(pots), thevoice multiplexerprovides four 10/100 base-t ethernet ports andfour rs-232 ports and four channel e1 ports.all ports operate simultaneously over the fiber optic cable, and may be used with leased lines to build up private networks and private telephone networks.
its merits include complete warning function, high integration, low consumption, stable performance and convenient usage.
the 30voice(fxs/fxo)phone over fiber multiplexer canbe managed by snmp management, user can monitor kinds of devices operation status easily.the device can support ac220v(110v) or dc48v power, or duoble power.

characteristic:
provides 4 channel e1/ g.703 for option;
provides 4 channel 100m (liner) ethernet ports for option;
provides 30 channel voice port, fxo and fxs for option;
provides4 channel rs232, rate supports 300-15200 bps for option;
ethernet port 10/100m, full/half duplex auto-adaptable and supports vlan;
ethernet port supports auto-mdix (twisted cable and straight cable auto-adaptable);
1-30 channel voice connection, supports calling indication;
voice port supports o port and s port, o port connects switch and s port connects users phone;
optical interface supports sc/fc interface and supports single fiber interface
support snmp network management (optional)

product function:

baudcom cwdm device is a sort of multi-service processing and transmission device that designed especially for point-to-point applications. It provides interfaces such as atm, gigabit ethernet, stm-1/4/16 and oc-3/12/48 on the basis of a transparent transmission platform constructed by virtual fiber-optic capability enhancing devices, which can fulfill upstream/downstream transmission services at various speed including 100/155/200/622/1000/1250/2500m, and entirely increase the performance/price ratio of the optical network platform.

the device adopts a box structure.the products front panel provide optical interfaces for channels and lines, working and alarm indicators, 10/100m auto-negotiating network management interfaces, rs232 network management commissioning interface etc., and the rear panel providing ac 220v / dc -48v power supply socket interfaces and power switches etc.

thevoice over fibermultiplexerispoint to point fiber transmitting equipment, which realizes 18 channelvoice (fxo, fxs) pots phoneover fiberand4 e1, 4*100methernet, 4 channel rs232 for option. Its merits include complete warning function, high integration, low consumption, stable performance and convenient usage.

features

provides 4 channel e1/ g.703 for option;

provides 1 channel100m(liner) ethernet ports for option

provides 8 channel voice port, fxo and fxs for option; also for 2/4 wire e&m

provides 4 channel rs232, rate supports 300-15200 bps for option;

ethernet port 10/100m, full/half duplex auto-adaptable and supports vlan;

ethernet port supports auto-mdix (twisted cable and straight cable auto-adaptable);

1-8 channel voice connection, supports calling indication;

configuration: point to point;

• realizes long-distance monitoring of local device to the remote device ;
• provides116 channels Ethernet ports, 10M/100M, full half duplex self adapt, support VLAN
• The Ethernet interface supports AUTO-MDIX( cross over and straight through self adapt)
• 4Ethernet interfaces support channel separate function, can set VLAN based on TAG
• provides two clock types: E1 master clock, E1 line clock;
• provides 3 kinds of loop-return function, namely E1 self-looping at local end, Ethernet self-looping at local end, ordered to self-loop at remote end;
• realize the automatically rate set of local device to remote device
• has the function of pseudo-random code testing, convenient for opening of the circuit, and can be used as an error code instrument;
• Ethernet supports rate of N*64k (N=1-32), which can be regulated from 64K to 1098K;
• supports 75 unbalanced and 120 balanced impedance at the same time;
• Provide Ethernet auto reset function, run more stably
• various Ethernet data indicate functions, which indicate data transmission status timely;
• Provides 1-16 voice channels, support calling indication;
• Voice connector FXO (FXS), FXO connect to PBX and FXS connect to phone;
• support 4 wire E&M
• RS232 channel can transfer asynchronous serial data with self-adaptable baud rate of 300 to 115.200;

Overview

BD-OP-16E1-4GE is the 16E1 point-to-point optical transport equipment that uses the FPGA chips and it is easy to upgrade. It is single board structure and the largest transmission capacity is 16E1 and 4*1000Mline Ethernet data, one channel RS232. the Ethernet bandwidth is set on base on multiple of 32K.The outer design use the standard 19 inches rack, so the volume is small, weight is light and operation is convenient and credit.

overview:

bd-op-8e1-4ge is the 8e1 point-to-point optical transport equipment that uses the fpga chips and it is easy to upgrade. It is single board structure and the largest transmission capacity is 8e1 and 4*10/100*1000m ethernet data.the outer design use the standard 19 inches rack, so the volume is small, weight is light and operation is convenient and credit.feature:

• provides 8 e1 transparent transmission ;
• provide 14 channel 10/100*1000methernet , 4 ethernet support vlan isolation for option
• the rate of optical port is1.25g, transmission
• e1 interface code is hdb3e1 vibration characteristic conforms to itu-t g.703g.823 and g.742;

• ethernet port supports full/half duplex, 10m/100/1000mauto-ataptable;
• has complete alarm function for device status;
• supports e1 loop from remote so as to detect and manage device conveniently;
• he combination ac220v and dc-48v for redundant for option

product description:
4e1fiber optical multiplexer is the 4e1 point-to-point optical transport equipment that uses the fpga chips and it is easy to upgrade. It is single board structure and the largest transmission capacity is 4e1. The outer design use the standard 19 inches rack, so the volume is little, weight is light and operation is convenient and credit.
4e1 fiber optical multiplexer, is use the pdh fiber transmission technologies. The 2m (e1) interfaces can connect with the exchanger, light loop device and multi-diplexer directly to form the mircomidi or the special network. Complete alarm function for 4e1, it is stable and easy to maintenance, install and small in size. It has one digital service telephone.

feartures:

• offer 4x 2mb/s digital interfaces
• the supervisory control interface implements centralized monitoring and export the monitor and control information of this port and opposite port.
• one link to service telephone for duty contract
• 220vac & -48vdc power options and the positive and negative of dc-48v can be optional because there is the self-test circuit for the polarity inside th1e device
• standard 19/9.5 inches rack, little volume, light weight, steady capacity and convenient setup
• digital clock recovery circuit and digital smooth dpll adopted for 2.048mb/s port
• led indicators
• has 1+1 fiber protection for optional
• power supply redundancy : ac220 and dc-48v or dc-24v combination

description:
4e1 fiber optical multiplexeris the 4e1 point-to-point optical transport equipment that uses the fpga chips and it is easy to upgrade. It is single board structure and the largest transmission capacity is 4e1. The outer design use the standard 19 inches rack, so the volume is little, weight is light and operation is convenient and credit.4e1 fiber optical multiplexer, is use the pdh fiber transmission technologies. The 2m (e1) interfaces can connect with the exchanger, light loop device and multi-diplexer directly to form the mircomidi or the special network. Complete alarm function for 4e1, it is stable and easy to maintenance, install and small in size. It has one digital service telephone.

features:

• offer 4e1 digital interfaces
• offer one 10/100m ethernet channel for option, 2channel rs232 for option
• the supervisory control interface implements centralized monitoring and export the monitor and control information of this port and opposite port.
• one order wire for service telephone for duty contract optional
• 220vac & -48vdc power options and the positive and negative of dc-48v can be optional because there is the self-test circuit for the polarity inside th1e device
• standard 19/9.5 inches rack, little volume, light weight, steady capacity and convenient setup
• digital clock recovery circuit and digital smooth dpll adopted for 2.048mb/s port
• led indicators
• has 1+1 fiber protection for option
• power supply redundancy : ac220 and dc-48v or dc-24v combination

Overview:
As a cost effective solution for the traditional telecom services migrate to the IP packet networking technology, BD-4E1-IP adopts the innovative TDM over IP technology, it transports the legacy E1/T1 data through the existing Ethernet or IP network.
BD-4E1-IP is the new generation of the TDM over IP equipment with IP circuit emulation that supports transportation of four E1/T1 and two local Ethernet ports over Ethernet or IP network. The uplink ports and user data ports are IEEE 802.3 compliant, 10/100BaseT auto-sensed Ethernet port.
The state-of-the-art design provides the highest availability with the accurate timing signal and data bit stream reconstruction. Predefined system parameter profiles that according to different application requirement; ultimately simplify the installation process and saving the maintenance cost.
Telecom and Enterprise users can save a lot of access and equipment costs and generates new revenue by offering different types of service over existing Ethernet networks. It is also suitable for connecting to the wireless equipment to achieve fast deployment of E1/T1 services. One particular application is to build E1/T1 links with low cost Wireless LAN bridges, replacing much more costly microwave radios. Operators can use BD-4E1-IP to provide legacy TDM services over wired or wireless packet network.

Features1. User-friendly Web server supported for easy setup and maintenance2. Point to point and point to multipoint supported3. Four E1/T1 Ports supported, E1 or T1 easy selected by Web Manager4. Uplink ports 1+1 backup supported5. Stable E1/T1 clock recovery, low jitter and wander6. Low processing delay for E1/T1 channels, high bandwidth usage efficiency7. Resist to packet loss, with PCM frame synchronization protection8. User definable encapsulation packet size for different application9. Enough jitter buffer to resist packet delay variation (PDV)10. Local Ethernet port throughput limiting, assuring E1/T1 QoS11. Local and remote E1/T1 LOS and AIS and packet loss indication for trouble-shooting andmaintenance.

12.SupportIETF RFC4553 SAToPprotocol, Ethernet encapsulation support IP/UDP

13.E1 clock supports 3 mode: local clock, adaptive and loopback

14.Ethernet built-in layer 2 switch, support VLAN(port based, 802.1Q based and QinQ based), QoS(port based8021.1P basedMAC based and TOS based).

15.Ethernet supportIEEE 802.3x, RSTP (802.1w), LLDP, CDP, Ethernet ring protection, OAM and MAC address automatic learning

16.Support POE (maximum power: 60W) (optional);

16voice phone fiber multiplexer is point to point fiber transmitting equipment, which is designed on large scale integrated circuit, realizes 14 e1 circuit, 14channels 10/100/1000methernet, 16 channel voice (fxo/fxs) and 12 channel rs232. Its merits include complete warning function, high integration, low consumption, stable performance and convenient usage. In the 16channel voices, the fxs and fxo can be combinated freely, for example, 8*fxs+8*fxo.

feature

• provides1 4 channel e1/ g.703 for option;
• provides 14 channel1000m(line) ethernet ports for option;
• provides 16 channel voice port, fxo and fxs for option;
• provides12 channel rs232, rate supports 300-15200 bps for option;
• ethernet port 10/100/1000m, full/half duplex auto-adaptable and supports vlan;
• ethernet port supports auto-mdix (twisted cable and straight cable auto-adaptable);
• 1-16 channel voice connection, supports calling indication;
• configuration: point to point;
• voice port supports o port and s port, o port connects switch and s port connects users phone;
• optical interface supports sc/fc interface and supports single fiber interface

power can support dc48v or ac220v or ac+dc

16e1 fiber optical multiplexer can multiplex to16 e1 and 8ethernetsignals for transmission over an optical fiber, resulting in reaching a longer distance without a repeaters and superior performance compared to copper media.

the 16e1 fiber optical multiplexer is the 16e1 point-to-point optical transport equipment that uses the fpga chips and it is easy to upgrade. The outer design use the standard 19 inches rack, so the volume is little, weight is light and operation is convenient and credit.

the 16e1 fiber multiplexer can support kinds managements (snmp, consol etc.it is easy for operation and maintain.

features

• provides 16 e1 transparent transmission ;
• provide 8*100m line ethernet channel, support mutual negotiate;
• support rs232 console port or telnet port to control local and remote pdh
• 4*voice interface; voice interface supports fxo port and fxs ports and 2/4-wire e&m audio (option);
• provice one hotline channel for option;
• e1 interface code is hdb3e1 vibration characteristic conforms to itu-t g.703g.823 and g.742;
• ethernet port supports full/half duplex, 10m/100m auto-adaptive;
• ethernet port supports vlan function and has 8 division mode for user selection;
• has complete alarm function and can monitor remote device status;
• supports e1 loop from remote so as to detect and manage device conveniently;
• the combination ac220v and dc-48v for redundant

description

the 4e1 fiber multiplexer is part of multi e1 and fast ethernet transmission system family, used to build a 150mb/s optical point-to-point link. Based on an asic chip; it performs the transportation of 4 e1 and a fast ethernet at full speed. The 4e1 fiber multiplexer (bd-op-4e1-4eth/m) also provides an order-wire and an auxiliary uart interface for management. The optimux offers a highly integrated solution for the perfect function, stable performance and convenience with low power consumption.

the fiber optical multiplexer can support gui management, which monitor the devices operation status. The user also can configure the device easily.

features

• merges the ethernet and time-division multiplex (tdm) transmission to the same pipe.
• provides 4*e1 and 4*100mb/s fast ethernet interface(sharing same 100m bandwidth).
• the standard e1 interfaces comply with itu-t g.703, g.823 and g.742.
• supports either auto-negotiation or hardware configuration selection of the ethernet operation.
• the ethernet interface supports vlan and flow control function(set by rs232 nms).
• real-time monitoring and all necessary alarm display for easy management.
• supports local and remote loop-back test.
• uses standard telephone set as order-wire(optional)
• provides one transparent rs232 interface for users data links.
• provides rs232 interface for network management.
• extends the fiber link up to120 kmwithout any repeater.
• compact single board terminal.
• support power ac (100220v) or dc (-48v),

model name:bd-dv10000
product function:thevideo fiber multiplexertransmit 1 channel digital video broadcasting, 1 channel high-fidelity audio, 1channel asynchronous date, 1channel 10/100m adapt ethernet date to one fiber efficiently. With complete digital and technology, dv 1000series support any high resolution dynamic or stationary picture high-fidelity transmit. It also can be anti-disturbance against several signals, environment, and work stably .it is widely used in security monitoring and control, high way, electronic police, automation, intelligent residential districts and so on.it can work shortly after it is installed. You could select any date interface by set. It is connected easily and it can indicate power supply, link, video, also adjust video. There are two ways to install: desktop and rack.
features:

• technical design, the whole surface by decoration.
• electrical circuit is designed by hardware scheme (except chip), and production is not effected by purchasing.
• complete digital fiber transmit platform.
• no need to adjust when opened.
• based on self copyright ic.
• no disturbance by analog in adjusting channel, picture and range.
• 4 steps filtering
• complete digital, broadcast transmit efficiently
• high speed 10/100m ethernet channel.
• full speed asynchronous date channel
• elastic configuration on the same platform.
• power supply, link, video by dynamic indication.
• self-adapt in pal, ntsc, secam.
• asic design
• farthest transmit distance:100km
• power supply:220v, -48v, +24, +12v, +5(optional)
• the two poles of direct power supply can be exchanged.
• support snmp management in our chassis installation.
• three installations: wall method, rack in 19inches 1u, or plug in-card.

interfaces:e1 interfaceline rate: 2.048mbps50ppmline code : hdb3interface standard: itu-t g.703e1 impedance: 75(unbalance)

10/100base-t interfacerate: 10/100m, full/duplex auto-negotiationprotocol: support vlanmac address entiries: 1k entiriesphysical interface: rj45, support auto-mdixrate: 1-100 mbps adjustable by software

v.35 interfaceelectric level: in compliance withccitt v.35 standardphysical interface: db25interface bit rate: 2.048mbit/ssupport dce(master clock), dce(lineclock), dte(v.35 interface clock).fxo/fxs interfaceelectric level: in compliancewith ccitt v.35 standardphysical interface: db9interface bit rate:2.048mbit/s

rs232 interfacetransmission mode: full-duplextransmission speed: 110115.2k bpsoptical interfacespeed of optical interface: 155mbpstype of optical connectors: fc/scfocus wavelength: 1310/1550 nmoptional transmitting distance: 0120 km(can becustomized by customer)

power supply
working voltage range wide, goodanti-disturb and isolation, work stableoption I dc-48v, range dc-36vdc-72coption ii ac220v, range ac165vac240vpower consumption:

• 128channels encoded and non-compression broadcast quality video transmission
• directly compatible with ntsc, pal, and secam cctv camera systems and support rs-232, rs-422, and rs-485 data protocols
• support any high-resolution video signal
• use cwdm technologyand output 8 wavelength , then transmit over onefiber
• automatic compatible pal, ntsc and secam video system
• 1-4 channels audio (optional)
• 1-4 channelsasynchoronus data(optional)
• 1 port 10/100mbps ethernet (optional)
• power supply and other parameter status indication, which can monitor the operation condition of system
• support no-damage regenerative trunk of video
• constant input optical power, and large dynamic range , no electrical or optical adjustments required .
• industry-grade of operating temperature from -40 to 85 degree, which is applied to the different working environment
• hot-swap supportted
• 19inch 4urackmount chassis design and comply with 8 pcs video module. Every video module support 16 channel video

thefiber optic video transceiverscan simultaneously transmit 1-8 channels of 8-bit digitally encoded broadcast quality video / return or bidirectional data / unidirectional or bidirectional audio / ethernet / telephone / dry contact over one multimode or single-mode optical fiber. These multiplexers are typically used in applications where the cameras have p/t/z capabilities. Plug and play design ensures the ease of installation and operation. Electronic and optical adjustments are never required. Led indicators are provided for instantly monitoring system status. Devices are available for either standalone or rack-mount installation , which is suitable for different working environment .

• 8channels encoded and non-compression broadcast quality video transmission
• directly compatible with ntsc, pal, and secam cctv camera systems and support rs-232, rs-422, and rs-485 data protocols
• support any high-resolution video signal
• automatic compatible pal, ntsc and secam video system
• 1-4 channels audio (optional)
• 1-4 channelsasynchoronus data(optional)
• 1 port 10/100mbps ethernet (optional)
• power supply and other parameter status indication, which can monitor the operation condition of system
• support no-damage regenerative trunk of video
• constant input optical power, and large dynamic range , no electrical or optical adjustments required .
• industry-grade of operating temperature from -40 to 85 degree, which is applied to the different working environment
• hot-swap supportted
• stand-alone type or card-type installed in 19 inch2u or 4u rack-mount chassis.

features:

up to 1.25gb/s data links

hot-pluggable sfp footprint

1310nm fabry-perot laser transmitter

duplex lc connector

compliant with sfp msa and sff-8472

digital diagnostic monitoring(ddm):internal calibration or external calibration

very low jitter

no rate select input required for

fiber channel 1x/2x operation

up to20kmon 9/125m smf

metal enclosure, for lower emi

single 3.3v power supply

low power dissipation