Organix Building System

UAE, United Arab Emirates

FortFlex 9000 A high performance, epoxy lining designed to cure at low temperatures and exhibit excellent resistance properties to a wide variety of chemicals and corrosives. Maintains flexibility and toughness better than standard epoxies of this class. Exhibits excellent adhesion, sag resistance and corrosion resistance. It is a high 100 % solids, flake filled, premium epoxy coating designed for internal steel and concrete substrates with high impact resistance, superior bonding ability to steel and concrete, resistance to broad range of chemicals.

Uses

• Chemical storage Tanks
• Oil Storage Tanks
• Waste water applications
• Cold Water reservoir
• Industrial and Residential Water tank

Chemicals ResistanceFortFlex 9000 is resistant to a broad range of chemicals such as fuels, salts, alkalies, some solvent, and many acids (including concentrated sulphuric acid).

Surface PreparationSteel Immediately prior to application of the coating or lining, the steel substrate must be clean of all oil, grease, dirt, mill scale, rust, flash rust, corrosion products, salts solvents, chlorides, other chemicals, and existing coatings.All welds must be smooth and continuous, no skip welds. All weld splatter, buckshot, laminations, and slivers must be removed and ground smooth; undercuts and pinholes must be ground smooth and filled with weld metal. All projections, sharp edges, high points and fillets must be ground smooth to a radius of at least 1/8 in and all corners must be likewise rounded.
All pitting, gouges, scratches, and other defects must be repaired either by welding or by illing with repair materials that are compatible with the coating or lining system and suitable for the intended service conditions. All surfaces to be coated or lined be readily accessible. The steel must be blasted to a minimum near white metal finish (SSPC SP10) with a 100 micron dense, sharp anchor profile free of peening, as measured by ASTM D4417.

ConcreteImmediately prior to application of coating, concrete substrate must be adequately cured (generally, at least 28 days)., structurally sound, free of all dirt, dust, debris, oil, grease, fats, chemical contamination, salts, solvents, surface hardeners, incomplete curing compoundsand foam release agents, laitance and efflorescene. Concrete surface must be dry.Locate all expansion joints, controls joints, floor drains, equipment base plats, and mid-floor termination points. Handle them as per construction details.Concrete is a very porous material. As it warms during the day it expels air, or ‘outgases’. Coating applied while concrete is out gassing will likely develop bubbles and pinholes.To avoid this, the material should be applied when the temperature of the concrete is falling. Usually this is from late afternoon into the night. Stop applying the material well before dawn. So it has time to set up firm to touch before out gassing begins. This may be anywhere from 1-6 hours, depending upon the weather conditons. In addition, it is good idea to shade the work area from direct sunlight. Do not apply material when temperature will fall within 3°C of the dew point.Priming may be required in situations where out gassing could be a problem.

Application

• MIXING-Use a jiffy type mixer. When operating the mixer avoid plunging it up and down in the bucket. The can fold air into the resin, which may cause bubbles to form in the coating after it has been applied. Individually stir each separate Part A and Part B component to a smooth, uniform consistency and colour.
• Spray-Immediately before applying a spray coat, stripe all continuous welds and edges with a brush-coat to assure adequate protection of the areas. All spray equipment should be clean and in proper working order
• COVERAGE-1.0 litre of coating applied wet at 350micron thick (2 coats applied at 175 micron each) will cover 3-4 square meter.

Curing

• Surface temperature
• 24°C Dry to touch – 12 hours, Final cure – 36 hours before immersion
• 32°C Dry to touch – 4 hours, Final cure – 24 hours before immersion

SafetyHandle with care, before and after use. Follow local safety regulations. All skin contact with resin products should be avoided. Barrier creams should be used and operatives should wear protective clothing for further information please request the Material Safety Data Sheet of this product.

We offer high-performance elastomeric waterproof coating chemical. Drytex.sg82 is a fluid applied emulsion modified with blend of synthetic polymers and special additives with good thyxotropic performance provides an effective monolithic air, vapor and water proof when applied to most surfaces. drytex.sg82 cures to a tough monolithic, highly flexible seamless coating, which brings you state-of-the-art waterproofing technology rubber-like membrane with good adhesion to almost any solid substrate.

FERICOAT – E2600 is a two-component, high-performance solvent free epoxy based protective coating acceptable for either topside or in constant submersion duty. t provides excellent adhesion, chemical resistance, hardness and durability in harsh or abusive environments making it a favorite in many commercial applications. A government spec formula so you know you are getting the best! Use FERICOAT – E2600 wherever salt air and abusive weather conditions require an exceptionally hard, highly durable rust preventative epoxy barrier coating. It provides outstanding protection in virtually all interior and exterior applications. Intended for use on all metals, wood, fiberglass, aluminum, composite materials, concrete and masonry. Acceptable for use on hulls, bulkheads, decks, machinery, high traffic areas, control panels, cabinets, material handling equipment, gangways and ramps. Use it to refinish and protect water tanks and piping. Apply using brush, roller or spray (conventional, airless or electrostatic).

Features

• A barrier coating acceptable for use above or below the waterline.
• Provides outstanding resistance to chemicals and spilled fuel.
• Produces an exceptionally hard scuff resistant finish.
• Provides superior adhesion, hardness and durability.
• Self leveling formula reduces brush and roller marks.
• Produces beautiful finish available in 100 colors plus clear.
• The hard, tough, durable finish offers unsurpassed stain, chemical, and abrasion resistance
• Extreme chemical resistant
• FERICOAT Epoxy coatings are extensively utilized in protective coatings due to their generally high level of mechanical properties, corrosion protection and chemical resistance. In the last few decades epoxy coatings have evolved from high VOC systems to more environmentally friendly technologies with high solids solvent-free coatings Rather, FERICOAT – E2600 provide unique technical solutions to overcome well known problems that have remained unsolved for many years in our industry, like adhesion to, blistering promoted by osmotic pressure, poor stain resistance against acidic foods, and color stability

Application Factors The various factors which play a significant role in influencing the performance of a coating system applied to a substrate include the shape, absorbency, dryness, chemical reactivity, flexibility, temperature and texture

Recommented PreparationFor best results remove old paint, loose scale, wax, oil and contaminates. Sand or scuff all surfaces prior to the application of any primer or coating. Fiberglass, aluminum, concrete, masonry and stainless steel, galvanized steel - strongly recommend the use of FERICOAT – E2600. All wood surfaces must be thoroughly cleaned and dry before the application of primer or coatings. Steel: All surfaces must be thoroughly dry and free of contaminates before the application of any primer or marine paint.

ApplicationFERICOAT – E2600 supplied as two components, comprising part A and part B. Part B is added to Part A prior to the application and requires mechanical stirring. This mixture can be applied. Brush roller or good result also attained by spraying. Application of an undercoat will provide depth in color and durability to the finished surface. Use the largest Brush possible. Long flexible bristles are best and a good technique is the criss-cross method.

Apply With BrushApply to the surface with a diagonal brushing action from the left to the right. This is then spread further with horizontal strokes before finally laying off with light vertical strokes. This results in any brush marks being able to flow out to give the best possible finish.

PackingAvailable as a two component kit. 1 US G /5 US G Kit.

Thin And Clean UpThinning not typically required. Use only with ORGANIX recommended thinner. Clean all equipment thoroughly with Lacquer Thinner or ORGANIX recommended one. Clean up with Lacquer Thinner ORGANIX recommended one.Use proper clothing, preferably minimum 60% cotton and equipment to protect skin from contact even though here are no specific antidotes for skin irritation. If it gets in eyes, should be washed with water or saline solution at least for ten minutes. Safety boots that are anti-static should cover at least the ankles. Natural ventilation is necessary during the application. Avoid spraying in high wind. Consult ORGANIX safety support for further assistance

CARESEAL GS 204 Grout Sealer is an affordable, water-based penetrating sealer that will provide protection against most common stains for sanded and non-sanded cementitious grout joints. It can also be used as a pre-grouting sealer. CARESEAL GS 204 is an aqueous fluorochemical dispersion that provides a durable, subsurface, transparent protective barrier against oil and water on porous mineral surfaces such as stone and tile. The product is used in waterbased penetrating sealers for stone, unglazed tile, grout, terra cotta, and other porous mineral surfaces such as concrete and brick. CARESEAL GS 204 provides oil and water repellency, stain resistance, and easy stain cleanup.

Features

• Water based sealer
• Protection against most common stains
• Easy to apply and will not alter the colour of the grout joint
• For interior and exterior applications VOC comply

UsesRecommended for indoor and outdoor use, on a wide variety of surfaces, ncluding natural stone, tile, paving, brick, kitchens, bathrooms, laundries, pool surrounds, garages, entertainment areas and patios. Can be used on porous tile, natural stone, masonry

Surface PreparationSurface must be dry and free of contaminants , including previously applied sealers , dirt , lime and hard water deposits , rust and other heavy soil and grime.Allow new grout installations to cure for at least 48 hours before applicationSurface and sealer temperature should be between 5C° and 46C°

Packing5 L , 20 L

StorageStore materials between 40°-90°F with careful handling to prevent damage to products. If conditions exceed these ranges, special consideration in storage must be taken. Do not store at high temperatures in direct sunlight. Shelf life under normal conditions in closed container will be 12 months.

Warranty On preapproved, qualified applications, when you use an approved applicator, a 25-year warranty is available. Contact us for complete warranty information

WAFSHIELD.IB645 is a fluid applied, flexible protective coating formulated with elastomeric resin which forms a membrane that expands and contracts. WAFSHIELD.IB645 specifically formulated and designed to apply over all types of substrates from concrete, precast concrete, various type of concrete blocks, cement board, stones, metal, plastering and wood as a waterproofing, air, moisture, fire barrier and UV resistant protection. It will not crack, crumble, or peel despite exposure to severe weather or total joint movement and retains its elasticity at very low temperatures and in extreme of heat, protecting from water and aggressive atmospheric chemicals.

Features

• Completely seamless protective membrane
• High performance waterproofing. Excellent Moisture, Air and Ignition barrier
• Energy Star rated product which saves Energy
• Optimum UV resistant, Abrasion resistant & Protects corrosion
• Good resistance to alkalis, salt solutions and diluted acids
• Non-Hazardous Composition and Non combustible
• Free of fibres and asbestos
• Low VOC, non-toxic and environmentally compliant
• Fire retardant (ASTM E 84 Class 1 & EN 13501 Class A)
• Thermal resistant, Resistant to movement and continuous contact with moisture
• Non toxic and high impact on building longevity
• Façade fire protection, Watertight, Vapour barrier and wind tight
• Water based and Non – flammabl

Application Field Facades, Roof, Curtain walls, Terrace to act as a complete barrier against air, water, vapor, fire and UV. Provides Moisture protection behind wall claddings of ACP, brick, Insulation systems, various other external façade finishing. Typical application projects with maximum fire resistance requirements. Envelope for high rise and rise residential, commercial and institutional towers, buildings and complexes.

Installation

• Surface Preparation - Surfaces to be coated must be clean, dry and free of any oil, grease or dirt. Patch and repair cracks, blisters and other problem areas using suitable materials recommended by OBS technical support. Any existing coating must be checked for good adhesion. The loose existing coatings should be removed well. Clean by wire brush and use pressured air to blow out all the dust.
• Application - Tools or equipments to be used for the application -Roller (Short nap roller), Brush (Good quality synthetic bristle brush), Spray (Airless Sprayer, 1gpm, 3, 000 psi, .027 or .031 tip)
• Mixing - Mix with a paddle and drill at low speed for 3 minutes for optimum consistency.
• Coating Application - All roof-preparation materials must be allowed to dry prior to application of the WAFSHIELD .IB645 coating. Immediately prior to application of the coating, all dust, dirt and other contaminants should be blown off the roof surfaces using compressed air. Apply the elastomeric coating by brush, roller or airless spray, using a multi pass technique to ensure even coating application to all sides of the substrate. Make a conscious effort to apply coating into crimped or pre-sealed vertical (side-lap) seams that have not been detailed. According to project specification and requirements , apply the second coat of WAFSHIELD . IB645 using a cross hatch technique.

Packing20 Kg

StorageStore materials between 10°C-50°C with careful handling to prevent damage to products. If conditions exceed these ranges, special consideration in storage must be taken. Do not store at high temperatures in direct sunlight. Shelf life under normal conditions in closed container will be 24 months.

WarrantyOn preapproved, qualified applications, when you use an approved applicator, a 25-year warranty is available. Contact us for complete warranty information.

Health and SafetyKeep out of reach of children. Ensure to maintain good ventilation during application and drying process. In case of skin contact, wash with soap and water or a recognized skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice. If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice. Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria.