sharjah, United Arab Emirates
Write a Review
Our Products
We offer the best product range of Butterfly Valve, Globe Valve, Butterfly Valves with Special Features, Swing / Wafer Check Valve and 2 Way Solenoid Valve.
These valves are used as an economical isolation valve instead of ball and gate valves.
"These valves are Used where throttling or both throttling and shut-off are required.
Pump throttling and quick quarter turn shut off control can be easily achieved in limited space areas. Lever operated valve stem, gear operated valve stem, square operating nut, chain operated valves, lug nut mounts.
These valves are used to prevent flow reversal in piping systems.
2-way piloted diaphragm solenoid valves Normal closed are capable of operating at zero differential pressure. They are capable of handling an operating pressure range from 0 PSI to 200 PSI. These valves are offered in a wide variety of diaphragm and body materials to provide on-off control of various fluids. Sizes 1/2" to 2", with coil voltage rating 21V DC to 220V AC, For gases use also availble in Aluminium Body.
The commissioning valve has hidden regulating and locking functions with high accuracy and good repeatability. The valve is fitted with two standard pressure test points, extended test points are available when required. A Micro-set two number position indicator is fitted to the adjustment handle for recording the valve position.
The flow rate controller is used in heating and cooling systems with circulation pumps. The controller automatically maintains flow at the set rate by measuring and immediately adjusting to any variation in pressure. No additional measurements are necessary and the correct quantity of water is supplied to all parts of the system under all operating conditions.
The flow rate controller maintains the flow at a constant rate that has been preset; the diaphragm responds to the pressure upstream of the regulating valve (via an internal impulse line) and dowstream. The valve settings directly refer to the volume flow; accordingly, the maximum volume flow is preset directly according to the diagram when the controller is fitted"
Aluminium 5/2 Way Spring return Pneumatic Solenoid Valves have 5 ports with 2 positions with the spring return system. This is one of the Pneumatic Industries most popular Aluminium 5/2 way solenoid valves and they can be mounted to aluminium manifold blocks for ease of installation and maintenance. These are ideal for compressed air control for pneumatic cylinder and air actuator control offering fail safe open or closed positioning depending on pipework set up. This compact design has the advantages of using Low Power 5 watt Coils reducing power consumption.
Diaphragm pilot solenoid valve with lower working pressure. Wide size range 1/8" to 2". Body material: Brass / stainless steel. Operating type: Normally closed / normally opened. Mode of action: 2/2-way, direct acting. Sealing material: NBR, EPDM or Viton.
The Angle Seat Valve is a 2/2-way pneumatically actuated piston valve for liquids, gases, steam and some aggressive fluids (vacuum services also). The superior design of the piston is unique to the market, enabling the plug to retract farther from the flow path, ensuring the highest flow capacity. The dual packing design, and a large diameter self aligning stem insures the highest cycle life. Angle Seat Valves are ideal for use in Commercial and Industrial Process Applications including Steam applications, Air drying equipment, Sterilizers, Autoclaves, Process control applications, Laundry equipment, Textile dyeing & drying, Bottling & dispensing equipment, Ink & paint dispensing, and Industrial compressors.
| The Single & Double Block CM40 forged barstock construction features a straight through (roddable) bore design. The roddable design allows the valve to be rodded out while in line and under pressure, should the valve become plugged. It also features a replaceable soft or metal seat, which can be easily removed and replaced, eliminating the need for valve removal should the seat become damaged by process conditions. It is ideally suited for severe process conditions (i.e. high temperatures, high pressure, and steam) or applications where valve plugging is a concern. |
Hydra-Cell pressure regulating valves bypass system fluid to prevent excess system pressure. When a system discharge is completely closed such as a closed spray gun, closed valve or plugged nozzle Hydra-Cell pressure regulating valves bypass the total system fluid flow. They also balance system pressure for multiple-orifice operations, essentially "regulating" the system pressure through bypassing of "excess" fluid.Internals of a C Series pressure regulating valve.
The Hydra-Cell Valve design is simple: a tapered plunger with a valve seat. When excess pressure overcomes the adjustable spring pressure on the plunger, the plunger lifts off the seat, allowing fluid to bypass and reduce system pressure. When a Hydra-Cell pressure regulating valve is mounted in the discharge line, its' modified flow-through design reduces wear on the plunger and seat. Baffles on either side of the plunger and seat extend life by directing the flow around these internal components.
The sealless design eliminate fugitive emissions leakage and is ideal for fluids containing particulate.
For service, simply remove the top of the body and replace the worn internal components. Hydra-Cell Valves can be serviced in place without removing any fittings or plumbing.
"The differential pressure controller is a straight-version proportional controller and works without auxiliary energy. The required nominal differential pressure can be continuously adjusted from 50 to 300 mbar. The adjusted set point can be read, locked and sealed. The nominal set point is factory preset at minimum. The required set point is adjusted by means of a hand wheel and secured against turning by the block ring. The impulse line (1000 mm) is included with the valve and is connected to a circuit regulating valve in the flow."
Wide variety of Needle Valves to meet the varying requirements of the Petrochemical, Power and Gas Industries.
Bore Sizes: 1/8"" (3.2mm), 3/16"" (4.8mm), 5/16"" (8mm) 3/8"" (9.5mm), 7/16"" (11mm), 5/8"" (16mm)
Straight Through (roddable) and globe pattern models
Needle (rising plug) and ball stem end models
Standard pressures to 6000 psig (414 barg), and to 10, 000 psig (689 barg) available
Various standard end-connections from 1/4" to 1" - threaded, socketweld, buttweld"
DD Wafer Double Disc Check Valves are constructed from rugged castings that are machined to exacting specifications. Reference individual technical data pages for standard disc, shaft, spring, and elastomer seat.
Pipeline Sizes from 2" to 48" 125 lb. to 1500 lb.
Designs Cast Iron, Carbon Steel and 316SS Vertical or horizontal installation"
CW Wafer Silent Check Valves are constructed from individual technical data pages for standard disc, seat, springs, and bushing rugged castings that are machined to exacting specifications.
"A pressure reducing valve (PRV) is a mechanical device designed to lower the working pressure of a liquid or gas from the supply side to the point of use side in a system. Although pressure reducing valves are used in numerous applications; this article will focus on PRV's as pertaining to a potable water plumbing system, but they may also be found in hydraulics, natural gas, air and steam to name a few
Designed for high pressure and temperature applications where elimination of metal components is desired. PVC, PPL and CPVC construction with FPM or EPDM seals, flanged connections. These swing check vavles can be installed horizontally or vertically and no flange gaskets are required.Options include counter weight for closing assistance (vertical installations), limit switch for position indication and spring assist closure.
Manifold Valves, available with hard or soft seat, are made of both carbon steel and 316 stainless steel with inline pipe threads or flanged configurations. All are helium leak tested. Mounting hardware is available. Manifold Valves connect system impulse line and transmitter.
Valves can be expanded to 16 stations.
Cartridge Valves have stainless steel body.
Valves are available with single-/multi-station manifolds. "
Designed for 14 to 24 inch pipelines, these rugged one piece polypropylene valves have a full face liner, eliminating the need for expensive flange gaskets. The 316SS valve stem is completely isolated from the pipeline and the unique sphered disc provides a bubble tight seal with minimum torque. These fabricated valves are easily customized for special pipeline connections. FPM, EPDM and Nitrile liner and seals, high torque gear box, dual lifting lug handles, slotted bottom bolt holes. Compatible with pneumatic or electric actuators.
The percentage of flow through the valves with either flow curve is equal to the degree of opening. As the valves are opened or closed, the flow varies in direct proportion to the valve opening. This permits predictable, accurate control of the downstream flow rate with a 1/4-turn valve.
These valves can provide a slow opening and fast opening flow curve with the percentage of flow equal to the degree of the valve opening. These provide predictable and accurate flow control with only a 1/4 turn of the valve handle. Compatible with pneumatic and electric actuators with positioners for automated modulating service applications. PVC or CPVC construction with FPM or EPDM seals for Methane Gas Recovery, Fill Station Lines, Lateral Take Off Line Flow Control, Flow Reduction for Pump Systems and Flow Control from Tanks.
One piece body butterfly valves for pipelines as large as 12" having a full 150 PSI pressure rating. The single piece design fully supports the flanged bolt holes and includes a integral mounting pad for level handle, gear box or actuator mounting (pneumatic or electric). Blow-out proof stainless steel stem with a unique full body liner having a V-notch retention design to assure positive sealing. Integrally molded face seal eliminates need for mating flange gaskets. These butterfly valves are designed for retrofitting to metal pipelines. Viton, EPDM and Nitrile liners with wafer body design.
CG Globe Silent Check Valves are constructed from rugged castings that are machined to exacting specifications. Their bodies have drilled flanges that are in accordance with ASME. Reference individual technical data pages for standard disc, seat, guide pins, and bushings. " individual technical data pages for standard disc, seat, guide pins, and bushings.
"A fire hydrant is an active fire protection measure, and a source of water provided in most urban, suburban and rural areas with municipal water service to enable firefighters to tap into the municipal water supply to assist in extinguishing a fire. Buildings near a hydrant may qualify for an insurance discount since firefighters should be able to more rapidly extinguish a fire on the insured property."
Vanguard General Trading FZC (Vanguard General Trading FZC)Vanguard General Trading FZC
Hamriya Free Zone G37 -08,
P.O.Box 49108 Sharjah - UAE
Share us via
