Post Your Requirement Menu

Welcome User

Other Products / Services

We are leaders in the market for providing best range of Butterfly Valve, Globe Valve, TUBULAR BACKWASHING FILTER SYSTEMS, Swing / Wafer Check Valve and Differential Pressure Transmitter

Butterfly Valve

Butterfly valve These valves are used as an economical isolation valve instead of ball and gate valves. Valves availble in Wafer types and Lug types Material Cast Iron and Stainless steel Size: DN 40 to DN 700 for Wafer type Size DN 40 to DN 300 for Lug type Dimension: as per 3202 - K1 Hand wheel operaiton and gear operation    

View Complete Details

Globe Valve

Globe Valve "These valves are Used where throttling or both throttling and shut-off are required. Classified as :Bellows Globe valves, Forged Steel Globe Valves, Piston type Globe valves. Material: Cast Iron, Carbon Steel and Stainless steel Pressure: PN 16 to PN 40 Dimension as per DIN 3202 Sizes DN 15 to DN 300 End connection Flange and Threaded"    

View Complete Details

TUBULAR BACKWASHING FILTER SYSTEMS

TUBULAR BACKWASHING FILTER SYSTEMS TUBULAR BACKWASHING FILTER SYSTEMS Strainer systems are generally used for particle retentions as fine as 100 mesh (150 microns), with some exceptions. Filter systems are designed to retain particles as small as 1 micron. Tubular backwashing filter systems temporarily reverse the flow through the filter element, backwashing and dislodging embedded particulate. When continuous flow is required, the filter system will consist of multiple chambers, ensuring that a minimum flow and a constant discharge pressure is maintained during the cleaning cycle.  

View Complete Details

Swing / Wafer Check Valve

Swing / Wafer Check Valve These valves are used to prevent flow reversal in piping systems. Classified as: Lift check Valves, Controlled Check valves, Disc Check Valves, Swing Check valves Material: Forged Steel, Cast Iron, Carbon Steel, stainless Steel Pressure: PN16 to PN40 Dimension as per DN3202, F1, K4, M9 end Connection Flanged and Threaded    

View Complete Details

Differential Pressure Transmitter

Differential Pressure Transmitter Using differential capacitance as detecting principle to constitute capacitance type differential pressure transmitter, inputting pressure is 0~1.2kPa to 0~10MPa, etc. Service medium: liquid, gas and vapor. Overpressure limit: impose 0 (absolute pressure) ~6MPa pressure on either side of the transmitter.  

View Complete Details

Float Control Steam Trap

Float Control Steam Trap "Steam traps are used for steam heating control in refineries, and other process plants. They are mainly of two types, float and thermodynamic Classifiction: Float controlled steam trap, Bucket type, Thermodynamic steam trap, Thermostatic steam trap Material: Forged steel, Cast iron, Carbobn steel End Connection: Flanged and Threaded Pressure: PN 16 to PN40 Size: DN15 to DN50"    

View Complete Details

Safety Valve

Safety Valve "A safety valve is a valve mechanism for the automatic release of a substance from a boiler, pressure vessel, or other system when the pressure or temperature exceeds preset limits. It is part of a bigger set of pressure safety valves (PSV) or pressure relief valves (PRV). The other parts of the set are relief valves, safety relief valves, pilot-operated relief valves, low pressure safety valves, and vacuum pressure safety valves. It comes on tow ypes spring loaded Size"" DN25 to DN10, dimension as per DIN 3202 - F2 "  

View Complete Details

FLUSHING STRAINERS

FLUSHING STRAINERS FLUSHING STRAINERS This is a type of modified simplex strainer, having the drain port connected to the bottom of the strainer basket, enabling "flushing" of retained particles when the drain valve is opened. The effectiveness of the cleaning is dependent upon the differential pressure of the system compared to the (presumably) atmospheric pressure of the drain port. Other factors include the particle characteristics, if they tend to be hard and non-deformable, this strainer design provide a low-cost/tech approach for reducing labor related expenses.  

View Complete Details

Butterfly Valves with Special Features and Options

Butterfly Valves with Special Features and Options Pump throttling and quick quarter turn shut off control can be easily achieved in limited space areas. Lever operated valve stem, gear operated valve stem, square operating nut, chain operated valves, lug nut mounts.  

View Complete Details

2 Way Solenoid Valve

2 Way Solenoid valve 2-way piloted diaphragm solenoid valves Normal closed are capable of operating at zero differential pressure. They are capable of handling an operating pressure range from 0 PSI to 200 PSI. These valves are offered in a wide variety of diaphragm and body materials to provide on-off control of various fluids. Sizes 1/2" to 2", with coil voltage rating 21V DC to 220V AC, For gases use also availble in Aluminium Body.  

View Complete Details

HYDRA-CELL METERING PUMPS

HYDRA-CELL METERING PUMPS Hydra-Cell pumps have a steady state accuracy of 1% with a repeatability and linearity to 3% or better, satisfying API 675 metering pump performance standards and therefore are often used as a high capacity metering pumps. P200 cutaway illustrationTo assist our customers with their metering applications and to help ensure maximum efficiency, the standard model F20, M03, D04, D10 and H25 Hydra-Cell pumps have been matched with a range of gearboxes and programmable pump controllers for precise flow adjustment, forming what we refer to as the P Series metering pump product line. Compared to conventional, expensive metering pumps, the unique high frequency Hydra-Cell design results in very smooth flow rates and reduced acceleration head without costly accessories such as pulsation dampeners.  

View Complete Details

HYDRA-CELL HIGH PRESSURE MACHINE TOOL COOLANT PUMPS

HYDRA-CELL HIGH PRESSURE MACHINE TOOL COOLANT PUMPS Hydra-Cell high pressure coolant pumps are sealless, meaning they do not have cups, packing or mechanical seals (the primary source of wear and maintenance for high pressure centrifugal and piston pumps). The inherent reliability of the Hydra-Cell design ensures minimal maintenance and down time. Conventional coolant pumps require fine filtration, in some instances as low as 25 microns. Filtering coolants to that degree can remove the very additives that enhance their performance. Over-filtering your coolant also results in high filtration costs (media cost, storage, labor and disposal). Hydra-Cell high pressure coolant pumps are generally protected with a 40 mesh (400 micron) screen or filter bag, so your filtration is not dictated by our pump but by whatever your rotary union or other system components require.  

View Complete Details

Snap-Ring filter bags

Snap-Ring Filter Bags Snap-Ring filter bags are designed for use with bag filter housings. Snap-Ring filter bags are the "economy" choice for basic liquid filtering applications to a nominal 65% to 70% level of efficiency. As the filter bag model/design improves, the material it is made from become thicker and the sealing method becomes more efficient. Snap-Ring filter bags utilize a sewn construction and are made from virgin materials. Snap-Ring filter bags seal the bag to the internal restrainer (support) basket via a metal or plastic "snap-ring". Generally speaking Snap-Ring filter bags should be used when the particle retention level is >25 microns and for applications that do not have much particle loading.  

View Complete Details

UniBag filter bags

UniBag filter bags are designed for use with bag filter housings. UniBag filter bags are considered to be a slight improvement over Snap-Ring filter bags and as such are also considered an "economy" choice for basic filtering applications to a nominal 65% to 70% level of efficiency. As the filter bag model/design improves, the material it is made from become thicker and the sealing method becomes more efficient. As with the Snap-Ring filter bags, UniBag filter bags are made with a sewn construction, although unlike Snap-Ring filter bags, UniBag filter bags are made from recycled fibers. What makes the UniBag filter bags an improvement over Snap-Ring style filter bags is the sealing method. UniBag filter bags have a crush seal design per the higher quality Sentinel, DURAGAF, LOFCLEAR, ACCUGAF and PROGAF filter bags. Unlike the snap-ring closure, the Sentinel style crush ring seal has larger contact area against the restrainer (support) basket. Downwards pressure from a separate sealing ring or from the bag filter lid (goose neck style bag filters) creates a bypass free seal and is therefore recommended for all applications, especially when the desired retention is

View Complete Details

PROLINE BAG FILTER HOUSINGS

PROLINE BAG FILTER HOUSINGS PROLINE bag filter vessels are an "economy" version of MAXILINE multiple bag filter housings because they are a non-code design and for operating pressures

View Complete Details

PROGAF filter bags

PROGAF filter bags are the epitome of high efficiency filter bag design, it sets the standards for all other in terms of particle loading and retention efficiencies. PROGAF filter bags are often used to replace specialized filter cartridges due to higher flow rate requirements or simply to reduce operating costs. Akin to the ACCUGAF filter bags, PROGAF filter bags also have a multiple layer construction; they have more layers and a special, patented sealing ring referred to as a STEP-RING, whose sealing against the restrainer (support) basket actually improves with increased differential pressure! PROGAF filter bags are used for critical filtration applications, often related to pharmaceutical, biotech, fine chemical and potable water/beverage applications.

View Complete Details

LOFTREX MELT BLOWN POLYPROPYLENE FILTER CARTRIDGES

LOFTREX melt blown polypropylene filter cartridges have a multi-density design to simultaneously retain both coarse and fine particles. The outer portion consists of non-woven melt blown polypropylene for retention of larger particles. The inner area consists of a bi-component polypropylene and polyethylene fiber inner core to retain the finer particulate that traversed through the melt blown section. LOFTREX are constructed as a single piece, it is not a two piece design with an inner core. No surfactants are present which could contribute to foaming or other undesirable performance and the material of construction satisfies FDA CFR 177 requirements LOFTREX filter cartridges are offered in four designs encompassing both nominal and absolute rated retentions and single and multi-zone designs for retentions within 0.50 to 150 microns. The following chart contains summary information and links to additional specifications and pricing by LOFTREX model.

View Complete Details

LOFMET POROUS TITANIUM FILTER CARTRIDGES

LOFMET filter cartridges are constructed of porous titanium and designed for applications involving extreme temperatures and operating conditions. Aggressive fluids and gases, high temperature and high pressure applications benefit from the rugged fixed pore LOFMET design and titanium powder material of construction. LOFMET titanium filter cartridges can be backwashed and cleaned for reuse repeatedly. The inherent mechanical strength and corrosion resistance is due in-part to a design that has no longitudinal seams. LOFMET filter cartridges have absolute particle retention ratings with a Beta 200 (99.5%) efficiency. The sintered titanium material of construction is compatible with a variety of corrosive liquids & gases, cryogenic fluids, high viscosity solutions, process steam, high temperature liquids & gases and catalyst recovery applications.

View Complete Details

Sentinel filter bags

Sentinel filter bags are the industry standard "every day" filter bags for industrial applications. Unlike less expensive Snap-Ring and UniBag filter bags are made from a heavier material and are all made from a fully welded construction. The heavier material provides slightly more depth filtration, essentially a torturous path for the fluid and particles to navigate; the particles are retained and the liquid passes through. The fully welded design increases the strength of the filter bag. The restrainer (support) basket relieves most of the weight stress from the filter bag, however the differential pressure stress will usually cause sewn seams to burst before welded seems would. Sentinel filter bags are made in the widest number of materials and retentions and their universal #1 through #4 sizes will fit any brand of bag filter designed for #1 through #4 sizes. Sentinel filter bags also provide nominal retention efficiencies of 65% to 70%.

View Complete Details

Level Transmitter

Level Transmitter Level transmitters are the extension and development of pressure transmitter technology. According to the principle that the liquid with different specific gravity are in linear relation to the pressure generating at different height to realize the accurate measurement and transmission of volume, level height and weight of water, oil and paste-state matters.  

View Complete Details

Flow Totalizer Universal input

Flow Totalizer Universal input, can be used with various types of sensors, transmitters used in conjunction, without compensation to achieve a liquid (such as water, oil) flow parameters measured display, alarm control, instantaneous flow transmission and cumulative flow totalizer; can receive orifice differential input or vortex flowmeter, turbine flowmeter, electromagnetic flow meter and other flow meter input signal; a prescription, small-signal removal and multi line input correction function; can achieve 4-bit 8-bit instantaneous flow and cumulative flow with the screen display. Through the serial communication port can be implemented in the host computer to read and write all parameters. By setting the instrument parameters can be quantitatively (volume) control.

View Complete Details

All Plastic Polypropylene, PVC or CPVC Cartridge Filter Housings

All Plastic PVC or CPVC Cartridge Filter Housings are used to remove fine particles from process fluid. These housings are designed to use single, open ended cartridges 10", 20" or 30" in length. Cartridges must have a 1" ID and these housings do not accommodate stackable cartridges. Viton Seal is standard. Temperature Ratings: 150 PSI at 70F OR 20 PSI at 200F FEATURES All Plastic Construction will never rust or corrode Compact, Easy to Install No Metal in Contact with Fluid Quick, Easy Filter Cartridge Changes FPM (Viton) O-Ring Seal Cartridges Available: 1, 5, 10, 30, 50, 75 and 100 micron retention in 10", 20" or 30" lengths

View Complete Details

Water proof crane control button station

Crane Switch "Water proof crane control button station is a new developed product with obtains the goods points of similar products in both here and abroad. The plastic cover is good-looking, strong and easy to catch. It has a reasonable advanced structure with a big capacity contact. The positive& negative direction control can be mechanically locked reciprocally. It also can be circuit locked reciprocally if necessary, which is secure and credit. It has a satisfactory button station with direct function switches and arrange. It has rubber and plastic cable cover and water-proof sealing, Thus it has a good performance(IP65 Level) in dustproof and waterproof and is very suitable for open air, rainy or snowy days, dusty environment or when it's operated by wet hands such as electric cucurbit, open air conveyer belt, and construction electric equipment remote control."

View Complete Details

5/3 Way Double acting solenoid valve

5/3 Way Double acting solenoid valve Aluminium 5/3 Way Double Acting Pneumatic Solenoid Valve has 5 ports with 3 positions and with twin coils offering one of the pneumatic industries most popular Aluminium 5/3 way solenoid valve. These are also ideal for compressed air control for pneumatic cylinder and air actuator control offering a stay put function as the fail safe position is stop even in mid stroke or actuator mid turn position . This compact design has the advantages of using Low Power 5 watt Coils with reduced power consumption,

View Complete Details

FLOWLINE BAG FILTER HOUSINGS

FLOWLINE BAG FILTER HOUSINGS The FLOWLINE model bag filter housing is an "economy" version of the SIDELINE bag filter housing and should be considered when ASME code stamping is not required. If you require an ASME code stamp, CRN or steam jacketing, the SIDELINE or TOPLINE models should be chosen. The FLOWLINE filter housing is applicable for all nominal micron retentions, if you require a specified efficiency (99% efficient) filter media, you should use the TOPLINE design.  Each FLOWLINE bag filter housing has a swing bolt cover which can be hinged in any one of four positions. The cover itself is what is referred to as an "evacuation cover" - a concave design that reduces the ullage (empty space) within the filter housing. The advantage is twofold; there's less "wasted fluid" during a bag change and the fluid level ends up lower in the housing to reduce spillage once the cover is opened. The cover is an investment cast component, ensuring precise, reliable sealing with concentric downwards pressure onto the bag hold-down ring. The restrainer (support) basket is made of 316SS and has 9/64" perforations. FLOWLINE bag filters also come with adjustable epoxy powder coated steel mounting legs. Optional features for FLOWLINE bag filters include Tri-Clover connections, differential pressure taps, mechanical/electro-polished internal/external and HAYFLOW basket upgrade.  

View Complete Details

Oval Gear Flowmeter

Oval Gear Flowmeter Electro magnetic flowmeter is designed for accurate liquid flow measurement. It utilizes state-of-the-art technologies in digital signal processing and electromagnetic sensor design. The converter is able to measure bidirectional flow and totalize the flow in both forward and reverse directions separately. Magnetic flowmeter has been widely used to measure the volume of conductive liquids such as water, sewage, acid, alkali, salt water as well as mixture of liquids and solids.  

View Complete Details

Coriolis Mass Flow Meter

Coriolis Mass flow meter Coriolis flow meters are instruments that, using the Coriolis principle, me. The structure of our Coriolis Mass Flow Meters was consisted of a pair of bended tubes. The principle is to detect Coriolis force forced a pair of tubes from inner mass flow by fluid. Coriolis meter artificially introduces a positive and negative Coriolis acceleration to the process. As illustrated in the diagram below, the entire process is split and re-directed through two curved tubes. The tubes are vibrated at a multiple of their natural resonant frequency. Miniature velocity transducers comprising of a coil & a magnet are each mounted on one of the tubes as shown. When no flow is present the tubes vibrate and the sine wave output of each velocity transducer is in phase. When flow is initiated the tubes will begin to twist due to the Coriolis acceleration induced by the moving mass. This causes the sine waves to shift in relation to one another (either lead or lag depending on the flows' direction) and a measurement is made.  

View Complete Details

Electro Magnetic Flowmeter

Electro Magnetic Flowmeter Electro magnetic flowmeter is designed for accurate liquid flow measurement. It utilizes state-of-the-art technologies in digital signal processing and electromagnetic sensor design. The converter is able to measure bidirectional flow and totalize the flow in both forward and reverse directions separately. Mag 888 magnetic flowmeter has been widely used to measure the volume of conductive liquids such as water, sewage, acid, alkali, salt water as well as mixture of liquids and solids.  

View Complete Details

switchgear items

Switchgear items We have big range of switch gear items from various manufacturers around the world. Main items include Cam Switch, CT Coil, Pedal switch, Panel Light, Limit switch, MCCB/MCB, electro SW, Proximity SW, Push buttons, panel meters analog and digitals, Sockets, Contactors, Pressure switch, Relays, distribution boards, Star delta panel, Main distribution boards.  

View Complete Details

Commissioning / Balancing Valve

Commissioning / Balancing Valve The commissioning valve has hidden regulating and locking functions with high accuracy and good repeatability. The valve is fitted with two standard pressure test points, extended test points are available when required. A Micro-set two number position indicator is fitted to the adjustment handle for recording the valve position.  

View Complete Details

Horizontal Gas Liquid Separators

31L Style Horizontal Gas Liquid Separators Gas liquid separators for up to 5% by weight of the units flow capacity" The Wright-Austin 31L series of in-line horizontal gas/liquid separators remove 99% of droplets and particles equal to or greater than 10 microns in a very compact design. As the moisture laden gas enters the separator, it encounters a curved, stationary blading structure welded to the inside of the vessel, and this causes a centrifugal force, propelling the droplets to the outer wall. The liquid coalesces and exits the separator's drain. Model 31L Wright Austin horizontal air liquid separators have an in-line barrel orientation and side inlet connections and can be used for both horizontal or vertical down flow applications

View Complete Details

FLOWASH PORTABLE BAG FILTER HOUSINGS

FLOWASH portable filter carts provide a convenient option for emptying and transferring industrial fluids such as machine tool coolant, waste water, paints and coatings and wastewater from sumps, pits and reservoirs. FLOWASH portable filter carts quickly empty or fill drums, barrels and totes. FLOWASH portable filter carts enable personnel to easily move the bag filter pump station to wherever it is required, instead of installing multiple stations by each process. TWO VERSIONS: BASIC AND INDUSTRIAL FLOWASH basic filter carts utilize an electrically operated self-priming end suction centrifugal pump designed to pump and filter water-like fluids up to 30 GPM at 75 PSI and 180�F. FLOWASH industrial filter carts utilize an air-operated diaphragm pump designed to pump and filter water-like fluids up to 45 GPM at 125 PSI and 150�F. FLOWASH industrial filter carts also include a strainer for pre-filtration. The design of the FLOWASH portable filter carts are based upon the FLOWLINEII bag filter design. The pump draws the fluid from its source and pumps it through the FLOWLINEII bag filter for filtration to as low as 1 micron nominal retention prior to discharge. A complete listing of filter bags are listed online at Eaton Filter Bags.com. You can decrease the frequency of filter bag changes with the HAYFLOW upgrade option if your filtration requirement falls within 1 to 100 microns (nominal).

View Complete Details

Peristaltic Pumps for Industrial Applications

Peristaltic Pumps for Industrial Applications Vector peristaltic pumps are available with hose sizes from " to 2" to provide flow rates from 0.1 GPM to 50 GPM for transferring fluids at pressures up to 60 PSI. Vector peristaltic pumps are used to transfer viscous, pure or other non-lubricating "difficult to pump fluids" such as egg yokes, custards, cold crmes and chemicals from a holding tank to a processing line. Vector pumps have excellent suction lift capabilities. Wanner Engineering, the innovative company that brought you the Hydra-Cell pump, has added another product to their industrial pump line - The Vector Peristaltic Pump. When you use a Vector Pump, nothing comes into contact with the fluid except the hose material. Since hoses can be changed quickly without coming into contact with the pumped fluid, they are often used to transfer solids laden waste water, chemical slurries and other volatile fluids in a safe, reliable manner. Vector pumps are an excellent alternative to air operated diaphragm pumps. They do not require air, will not stall when run at low RPM's and operate equally well in both hot and cold weather. And just like the Hydra-Cell, Vector pumps can be run dry!

View Complete Details

MODULINE BAG FILTER HOUSINGS

MODULINE BAG FILTER HOUSINGS MODULINE bag filter system should be considered for high flow rate applications where the flow rate cannot be interrupted for filter bag replacement as an alternative to a duplexed DUOLINE or MAXILINE multiple chamber bag filters. The MODULINE bag filter system offer a flexible approach for high flow rate filtration applications. Instead of a single housing having multiple filter bag chambers, the MODULINE system consists of 2 to 8 #2 size bag filter housings installed on a common inlet and outlet manifold. A key advantage of this approach is that you can change filter bags without interrupting the process flow rate. This is something that you cannot do with multiple bag filter housings unless you duplex them together. The MODULINE bag filter system is more expensive then multiple chamber PROLINE and MAXILINE bag filters, however it is less expensive then duplexing multiple bag filter housings. If your filtration requirement falls within 1 to 100 microns (nominal), also consider the HAYFLOW upgrade option, as it may reduce the number of bag filter stations required. The MODULINE bag filters systems are based upon the TOPLINE, SIDELINE, FLOWLINE and FLOWLINEII bag filter vessel designs.  

View Complete Details

Socket Tee

Socket Tee Socket Tee, also known as high pressure forging links, high pressure pipe fittings are suitable for high-pressure pipeline, its structure in many forms, according to the manufacturing process can be divided into (cold, hot) extrusion links, forging system links and welding links, welding thick-walled strengthening the links can be divided into welding links, welding a single bar to strengthen links and enhanced disc welded tee three. By Tee Tee external shape can be divided into oblique, orthogonal links and Y-shaped links  

View Complete Details

bag filter accessories

BAG FILTER ACCESSORIES Perhaps one of the most overlooked aspect of bag filter housings are the accessories available for improving performance. Displacement Balloons reduce volume of carry-out loss during filter bag changes. A #2 size filter bag has a volume of approximately 5 gallons, in addition to the added weight when changing the filter bag, that fluid is often discarded with the filter bag. The displacement balloon significantly reduces this wasted volume and also results in a much lighter, easier filter bag replacement. Bag Positioners are a REQUIREMENT for absolute retention filter bags such as ACCUGAF and PROGAF filter bags, helping to keep the filter bag positioned correctly within its' restrainer (support) basket. Magnetic Inserts are powerful rare earth magnetic assemblies suspended within the filter bag, attracting ferrous particles, both alleviating filter bag loading in addition to increasing filtration efficiency due to magnetic attraction.  

View Complete Details

Automatic Regulating Valve

Automatic Regulating Valve "The flow rate controller is used in heating and cooling systems with circulation pumps. The controller automatically maintains flow at the set rate by measuring and immediately adjusting to any variation in pressure. No additional measurements are necessary and the correct quantity of water is supplied to all parts of the system under all operating conditions.  The flow rate controller maintains the flow at a constant rate that has been preset; the diaphragm responds to the pressure upstream of the regulating valve (via an internal impulse line) and dowstream. The valve settings directly refer to the volume flow; accordingly, the maximum volume flow is preset directly according to the diagram when the controller is fitted"

View Complete Details

POLYLINE DUPLEX BAG FILTER HOUSINGS

POLYLINE DUPLEX BAG FILTER HOUSINGS POLYLINE duplex bag filter housings are for applications where the process flow cannot be interrupted for filter bag changing. Flow is diverted using linked valves simplify the switch-over procedure to a signal lever action. The POLYLINE duplex bag filters are based upon the POLYLINE bag filter housing design and are available in polypropylene, PVDF, PVC and CPVC material of construction. Please view the POLYLINE duplex pricing page for discounted pricing. If you require spare parts for an existing POLYLINE bag filter, please refer to the POLYLINE parts page for discounting pricing. If you are not sure which type of filter housing would be most appropriate for your application, please fill out our Filter Housing Inquiry Form and we'll reply within 1-2 business days.  

View Complete Details

turbine flow meters

Turbine flow meters Turbine flow meters utilize a proven flow measurement technology to provide exceptionally accurate and reliable digital outputs. Because of their versatility, these turbine flow meters are the solution for a wide variety of liquid and gas flow sensing applications. Turbine meters are an ideal solution when high accuracy, compact size, fast response, and high tolerance to shock and vibration are critical requirements. Turbine meter sizes range from 3/8 inch to 4 inches.  

View Complete Details

Temperature Transmitter

Temperature Transmitter Temperature transmitter is to amplify the electrical signals from the sensor, to correct and depending on the model galvanically insulate them. The conditioned signal can then easily be transmitted over long distances to the in-/output sections of a process control system or controller. Since the electrical signal from the thermocouple or resistance thermometer is relatively strong, signal amplification in close proximity to the sensors is not required.  

View Complete Details

PVC, CPVC and EASTAR (clear Copolyester) Duplex Basket Strainers

PVC, CPVC and EASTAR (clear Copolyester) Duplex Basket Strainers Protect System Components When pipeline system components require protection from dirt and debris and the line cannot be shut down for basket cleaning, an All Plastic Duplex Basket Strainer is the ideal choice. Unwanted particles are removed as the process media passes through a perforated strainer basket contained inside the strainer body. The basket traps the unwanted material while allowing the process media to flow freely.  Easy Basket Cleaning Cleaning or changing the strainer basket is quick and easy. Turning the operating handle on the diverter valve assembly switches the flow from one strainer housing to the other.  The cover features two angled handles for easy opening and closing. The housing has external cover threads that do not contact the process media eliminating the need for cleaning. Venting and draining are easily accomplished by using the hand removable, threaded plugs on the cover and the side of the housing. Plastic baskets in perforation sizes from 1/32  to 3/16 and stainless steel baskets from 1/2 perforation down to 325 mesh are available. To review the customizable datasheet for that strainer.

View Complete Details

Suction Diffuser

Suction Diffuser "Suction Diffuser mounts to the suction side of a pump in either a horizontal or vertical position. It is designed to remove any foreign matter that may be hazardous to the pump or other system components, while providing the proper flow conditions to the pump. Where space is limited, Suction diffuser can be used as an elbow (in some cases a reducing elbow) with a built in strainer for easy maintenance and system performance. Suction Diffusers are constructed from rugged cast iron castings that are machined to exacting specifications. These bodies have drilled flanges that are in accordance with ASME B16.1."  

View Complete Details

Stancor ANSI Centrifugal Pumps

Stancor ANSI Centrifugal Pumps (Manufactured from solid Kynar or PTFE) Stancor ANSI centrifugal pumps are designed to pump abrasive, corrosive and other types of aggressive industrial fluids with maximum reliability. With flow rates up to 700 GPM and discharge pressures up to 350 feet, Stancor pumps are used for applications where comparable alloy pumps require frequent replacement or are otherwise too expensive. Transfer of acids used in the textile, food, waste water treatment, paper making and primary metals industry are our most common applications. We area also used for lime slurry wet FGD gas scrubbing applications. The Stancor series is available with either conventional mechanical seals and sealless mag-drive configuration.

View Complete Details

LOFMEM FILTER CARTRIDGES

LOFMEM filter cartridges are made from Polyethersulfone (PES) and Teflon (PTFE) membranes under ISO 9001 quality control standards to provide absolute retention consistency. LOFMEM filter cartridges are used for final filtration of and beverages, ultrapure water filtration, DI water, photo resists, pharmaceutical intermediates, strong acids/bases, compressed gases and fermentation air.  LOFMEM filter cartridges are manufactured in an ISO Class 7 cleanroom and 100% flushed. LOFMEM filter cartridges have 7 ft2 to 8 ft2 surface area with an absolute retention range from 0.03 m to 1.00 m.

View Complete Details

DUOLINE DUPLEX BAG FILTER HOUSINGS

  DUOLINE DUPLEX BAG FILTER HOUSINGS DUOLINE duplex bag filter housings are for applications where the process flow cannot be interrupted for filter bag changing. Flow is diverted using valves; linked valves simplify the switch-over procedure to a signal lever action. The DUOLINE duplex bag filters are based upon the TOPLINE, SIDELINE and FLOWLINE bag filter housings, please review each design to determine which style satisfies your requirements best or contact us for assistance. If your filtration requirement falls within 1 to 100 microns (nominal), also consider the HAYFLOW upgrade option, as it may reduce the frequency of filter bag changes. Another consideration for continuous flow applications would be our automated filter systems, eliminating filter bag change-outs altogether. Please use the navigation menu to look-up the pricing for DUOLINE duplexed bag filters. Pricing is organized by diverting valve style. DUOLINE duplex bag filters are available with individual manually operated ball valves, butterfly valves and with linked butterfly valves as shown in the picture above. The linked valves simplify the diverting procedure and ensure uninterrupted flow. If you have an existing DUOLINE duplex bag filter housing and require spare parts, refer to the navigation menu for the applicable TOPLINE, SIDELINE and FLOWLINE bag filter housing spare parts. If you are not sure which type of filter housing would be most appropriate for your application, please fill out our Filter Housing Inquiry Form and we'll reply within 1-2 business days.  

View Complete Details

Reducer Fittings

Chemical pipe diameter pipe is one of two different diameters for the connection. Diameter pipe forming process is usually used to suppress necking, necking Expanding suppression or repression plus expander, for some specifications of the different diameter pipe can be applied stamping. diameter pipe is divided into concentric reducers and eccentric reducers, we gave birth to the diameter pipe of different materials such as carbon steel reducer pipe, alloy pipe reducer, stainless steel diameter pipe low temperature steel reducer, high-performance steel-diameter pipe, can meet your different choices...

View Complete Details

Level Gauges

Level Gauges Tubular Level gauge for visual liquid level observation is very common in process industry. It is a simple and reliable device for direct reading in atmospheric or pressurized tank applications. It is mounted parallel, along the side of tank. As the process level fluctuates, the level in the transparent glass tube changes accordingly and gives local liquid indication.  

View Complete Details

Elbow

Elbow Elbow is a commonly used pipe installed in connection with a pipe connecting two nominal pipe diameter the same or different, so the pipeline for a certain angle turn in the piping system, pipe elbow is to change the direction of the tube components in piping systems used in all the fittings, the largest proportion, about 80% are usually of different materials or thickness of the bend forming process to select a different present, commonly forming process seamless elbow hot pushing, punching, squeezing, etc.  

View Complete Details

Metal Tube Rotameter

Metal Tube Rotameter "It operates on the principle of variable area; the fluid in the metal tube raises the float in the taper tube increasing the area of passage of fluid. by a magnetic coupling the inner float movement through a series of linkages and counter weight. the tube and the float combination determines the flow rate. The inner float magnetic field is detected by the high sensitive magnetic field detection sensor , enable us to show the digital readout. "  

View Complete Details

Webster Non-Metallic Centrifugal Pumps

Webster Non-Metallic Centrifugal Pumps (mechanically sealed) The C5, C7 and C8 Series pumps are designed specifically for continuous chemical duty service. They are rugged, precision molded, and feature dynamically balanced, enclosed impellers. Units are available in CPVC (Corzan), fiberglass reinforced Polypropylene, and PVDF (Solef ) with ratings of 1/3, 1, and 1-1/2 horsepower. The standard mechanical seal is a John Crane Type 21 single seal, carbon/ceramic. Other seal materials are available depending on the process fluid. And, water-wash seals are available for especially aggressive or "crystallizing" liquids. Pump models are also available with a rugged cast iron bearing frame for belt-drive or other coupled drivers.

View Complete Details

Tell Us What are you looking for? Will call you back

Contact Us

  • Saad Chohan
  • Hamriya Free Zone G37 -08, P.O.Box 49108 Sharjah - UAE, Sharjah - 49108, United Arab Emirates